Asus RS120-E4 User Guide - Page 20
Installing the top cover
 |
UPC - 610839641819
View all Asus RS120-E4 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 20 highlights
2. Firmly hold the cover and slide it toward the rear panel for about half an inch until it is disengaged from the chassis. 5. Lift the cover from the chassis. 1/2 inch distance 2.1.3 Installing the top cover 1. Position the cover on top of the chassis with the thumbscrews on the rear, and leaving a gap of about half an inch from the front panel. 2. Make sure that the side markings on the cover (two on each side) are aligned to the grooves on the chassis. Side markings 3. Slide the cover toward the front until it snaps in place. 4. Tighten the thumbscrews on the rear to secure the cover. Thumbscrews Grooves 2- Chapter 2: Hardware setup
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15 -
16 -
17 -
18 -
19 -
20 -
21 -
22 -
23 -
24 -
25 -
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
 |
 |
Chapter 2:
Hardware setup
2-4
2.
Firmly hold the cover and slide it
toward the rear panel for about half
an inch until it is disengaged from
the chassis.
5.
Lift the cover from the chassis.
2.1.3
Installing the top cover
1.
Position the cover on top of the
chassis with the thumbscrews on the
rear, and leaving a gap of about half
an inch from the front panel.
3.
Slide the cover toward the front until it snaps in place.
4.
Tighten the thumbscrews on the rear to secure the cover.
2.
Make sure that the side markings
on the cover (two on each side)
are aligned to the grooves on the
chassis.
Grooves
Side markings
Thumbscrews
1/2 inch
distance