Brother International JS60 Operation Manual - Page 38

Using Optional Accessories

Get Brother International JS60 PDF manuals and user guides View all Brother International JS60 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

USING ATTACHMENTS AND APPLICATIONS USING OPTIONAL ACCESSORIES L Sewing buttons Needle Available stitch width ( ) 5 Available stitch length You will need to adjust the stitch width to f match the distance between the holes in the button. Turning the pattern selection dial will narrow or widen the "swing" of the stitch to accommodate most buttons. Turn the handwheel toward you g (counterclockwise) to check that the needle correctly goes into the two holes of the button. Single Any 2 Set according to the distance between the holes. (The illustration shows 2-5.) Measure the distance between the a buttonholes. Turn off the machine. b Attach the button sewing foot "M". c Place the darning plate on the needle plate. d CAUTION ● When sewing, be sure that the needle does not touch the button, otherwise the needle may bend or break. Turn on the machine. h CAUTION ● Do not turn on the machine while pressing down the foot controller. The machine may start unexpectedly and cause personal injury or damage to the machine. Start sewing. i • After sewing for about 10 seconds at a low speed, press and hold down the reverse sewing lever to sew a few reinforcement stitches. Pull the fabric to the left side of the j machine, and then cut the upper and lower threads, leaving a length of 15 cm (6 inches). Place a button between the presser foot e and the fabric. CAUTION ● Make sure the needle does not hit the button during sewing. The needle may break and you may be injured. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
USING ATTACHMENTS AND APPLICATIONS
——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————
37
USING OPTIONAL ACCESSORIES
L
Sewing buttons
a
Measure the distance between the
buttonholes.
b
Turn off the machine.
c
Attach the button sewing foot “M”.
d
Place the darning plate on the needle plate.
e
Place a button between the presser foot
and the fabric.
f
You will need to adjust the stitch width to
match the distance between the holes in
the button. Turning the pattern selection
dial will narrow or widen the “swing” of
the stitch to accommodate most buttons.
g
Turn the handwheel toward you
(counterclockwise) to check that the
needle correctly goes into the two holes
of the button.
CAUTION
h
Turn on the machine.
CAUTION
i
Start sewing.
•
After sewing for about 10 seconds at a low
speed, press and hold down the reverse
sewing lever to sew a few reinforcement
stitches.
j
Pull the fabric to the left side of the
machine, and then cut the upper and
lower threads, leaving a length of 15 cm
(6 inches).
CAUTION
Needle
Available stitch width (
)
Available
stitch
length
Single
Set according to the distance
between the holes.
(The illustration shows 2-5.)
Any
5
2
●
When sewing, be sure that the needle does
not touch the button, otherwise the needle
may bend or break.
●
Do not turn on the machine while pressing
down the foot controller. The machine
may start unexpectedly and cause
personal injury or damage to the machine.
●
Make sure the needle does not hit the
button during sewing. The needle may
break and you may be injured.