Brother International PT-P700 Master Command Reference - Page 15

Command Name, Description, Job ID setting

Get Brother International PT-P700 PDF manuals and user guides View all Brother International PT-P700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Raster Command Reference Descriptions for the numbers in the print data on the previous page are provided in the following table. For details on each command, refer to "4. Printing Command Details". No. Command Name Description １ Invalidate A 100-byte invalidate command is sent. 2 Initialize The "initialize" command is sent. 3 Switch dynamic command mode The printer is switched to raster mode. Send this command before sending raster data to the printer. 4 Job ID setting commands Internal specification commands Since this is a command for outputting with the commercial version driver, it is unnecessary for the user to send this command. 5 Print information command Media size information for the print data is sent. This is the command for "24 mm" tape. 6 Various mode settings This is a command for specifying a mode. (1Bh+69h+4Dh+00H) Here, nothing is specified. 7 Advanced mode settings This is the command for specifying settings for the advanced mode. In this case, "no chain printing" is enabled. 8 Specify margin amount Specifies the amount of the margins. This is the command for "15 dots". 9 Select compression mode TIFF compression mode is selected. 10 Raster data Raster data continues. 11 Print command Since it is not the last page, the print command is sent at the end of the page. 12 Switch dynamic command mode The printer is switched to raster mode. Send this command before sending raster data to the printer. 13 Job ID setting commands Internal specification commands Since this is a command for outputting with the commercial version driver, it is unnecessary for the user to send this command. 14 Print information command Media size information for the print data is sent. This is the command for "24 mm" tape. 15 Various mode settings This is a command for specifying a mode. (1Bh+69h+4Dh+00H) Here, nothing is specified. 16 Advanced mode settings This is the command for specifying settings for the advanced mode. In this case, "no chain printing" is enabled. 17 Specify margin amount Specifies the amount of the margins. This is the command for "15 dots". 18 Select compression TIFF compression mode is selected. - 11 - 2. Print Data

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Raster Command Reference
- 11 -
2. Print Data
Descriptions for the numbers in the print data on the previous page are provided in the following table.
For details on each command, refer to “
4. Printing Command Details
”.
No.
Command Name
Description
１
Invalidate
A 100-byte invalidate command is sent.
2
Initialize
The “initialize” command is sent.
3
Switch dynamic
command mode
The printer is switched to raster mode.
Send this command before sending raster data to the printer.
4
Job ID setting
commands
Internal specification commands
Since this is a command for outputting with the commercial
version driver, it is unnecessary for the user to send this
command.
5
Print information
command
Media size information for the print data is sent.
This is the c
ommand for “24 mm” tape.
6
Various mode settings
(1Bh+69h+4Dh+00H)
This is a command for specifying a mode.
Here, nothing is specified.
7
Advanced mode
settings
This is the command for specifying settings for the advanced
mode.
In this case, “no chain printing” is enabled.
8
Specify margin amount
Specifies the amount of the margins.
This is the command for “15 dots”.
9
Select compression
mode
TIFF compression mode is selected.
10
Raster data
Raster data continues.
11
Print command
Since it is not the last page, the print command is sent at the end
of the page.
12
Switch dynamic
command mode
The printer is switched to raster mode.
Send this command before sending raster data to the printer.
13
Job ID setting
commands
Internal specification commands
Since this is a command for outputting with the commercial
version driver, it is unnecessary for the user to send this
command.
14
Print information
command
Media size information for the print data is sent.
This is the command for “24 mm” tape.
15
Various mode settings
(1Bh+69h+4Dh+00H)
This is a command for specifying a mode.
Here, nothing is specified.
16
Advanced mode
settings
This is the command for specifying settings for the advanced
mode.
In this case, “no chain printing” is enabled.
17
Specify margin amount
Specifies the amount of the margins.
This is the command for “15 dots”.
18
Select compression
TIFF compression mode is selected.