Cisco VG202 Hardware Installation Guide - Page 45

Step 8, A summary of the available interfaces is displayed. - config

Get Cisco VG202 PDF manuals and user guides View all Cisco VG202 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Chapter 4 Powering On the Cisco VG202 and Cisco VG204 Voice Gateways Initial Configuration Procedures Step 8 Enter the virtual terminal password, which prevents unauthenticated access to the voice gateway through ports other than the console port: The virtual terminal password is used to protect access to the voice gateway over a network interface. Enter virtual terminal password: xxxxxx Step 9 Respond to the following prompt as appropriate for your network: Configure SNMP Network Management? [yes]: Community string [public]: A summary of the available interfaces is displayed. Step 10 Choose one of the available interfaces for connecting the voice gateway to the management network: Enter interface name used to connect to the management network from the above interface summary: fastethernet4 Step 11 Respond to the following prompts as appropriate for your network: Configuring interface FastEthernet0/0: Use the 100 Base-TX (RJ-45) connector? [yes]: yes Operate in full-duplex mode? [no]: yes Configure IP on this interface? [yes]: yes IP address for this interface: 172.1.2.3 Subnet mask for this interface [255.255.0.0] : 255.255.0.0 Class B network is 172.1.0.0, 26 subnet bits; mask is /16 The configuration is displayed: The following configuration command script was created: hostname VG enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1 enable password xxxxxx line vty 0 4 password xxxxxx snmp-server community public ! no ip routing ! interface FastEthernet0/0 no shutdown speed 100 duplex auto ip address 172.1.2.3 255.255.0.0 ! Step 12 Respond to the following prompts. Enter 2 to save the initial configuration. [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. Enter your selection [2]: 2 Building configuration... Use the enabled mode 'configure' command to modify this configuration. Press RETURN to get started! RETURN The user prompt is displayed. VG> OL-15959-01 Cisco VG202 and Cisco VG204 Voice Gateways Hardware Installation Guide 4-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
4-5
Cisco VG202 and Cisco VG204 Voice Gateways Hardware Installation Guide
OL-15959-01
Chapter 4
Powering On the Cisco VG202 and Cisco VG204 Voice Gateways
Initial Configuration Procedures
Step 8
Enter the virtual terminal password, which prevents unauthenticated access to the voice gateway through
ports other than the console port:
The virtual terminal password is used to protect
access to the voice gateway over a network interface.
Enter virtual terminal password:
xxxxxx
Step 9
Respond to the following prompt as appropriate for your network:
Configure SNMP Network Management? [yes]:
Community string [public]:
A summary of the available interfaces is displayed.
Step 10
Choose one of the available interfaces for connecting the voice gateway to the management network:
Enter interface name used to connect to the
management network from the above interface summary: fastethernet4
Step 11
Respond to the following prompts as appropriate for your network:
Configuring interface FastEthernet0/0:
Use the 100 Base-TX (RJ-45) connector? [yes]:
yes
Operate in full-duplex mode? [no]:
yes
Configure IP on this interface? [yes]:
yes
IP address for this interface:
172.1.2.3
Subnet mask for this interface [255.255.0.0] :
255.255.0.0
Class B network is 172.1.0.0, 26 subnet bits; mask is /16
The configuration is displayed:
The following configuration command script was created:
hostname VG
enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1
enable password xxxxxx
line vty 0 4
password xxxxxx
snmp-server community public
!
no ip routing
!
interface FastEthernet0/0
no shutdown
speed 100
duplex auto
ip address 172.1.2.3 255.255.0.0
!
Step 12
Respond to the following prompts. Enter
2
to save the initial configuration.
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.
Enter your selection [2]:
2
Building configuration...
Use the enabled mode 'configure' command to modify this configuration.
Press RETURN to get started!
RETURN
The user prompt is displayed.
VG>