Cobra XRS 9770 XRS 9770 Manual - Page 7

EasySet Programming - voice alert 15 band

Page 7 highlights

Your Detector EasySet Programming This EasySet programming menu lists all of the modes and settings you can choose from after you have entered Program mode as described on page 7. Mode Set IntelliShield City mode default* Tone Two beeps One beep One beep IntelliMute Two beeps mode One beep Set IntelliMute One beep RPMs IntelliMute Pro mode Two beeps One beep Auto Mute Two beeps mode One beep Set Compass Pop Detect mode One beep Two beeps One beep Display/Voice City X City X beep Off City X+K IntelliMute On IntelliMute Off Set IntelliMute (see page 15 to set activation point) IntelliMute Pro On IntelliMute Pro Off AutoMute On AutoMute Off Set Compass Pop Detect On Pop Detect Off Result A single beep sounds when the signal is first detected. Audio for all X band alerts are blocked until signal strength reaches Level 3. Combines the City X mode with prevention of K band audio alerts until signal strength reaches Level 2. All alerts (except for strobe signals from emergency vehicles) are automatically muted below the engine rev point you set. Normal operation. Allows you to set the engine rev point while using IntelliMute. Note: Only shown if IntelliMute is Off. All radar, VG-2 and Spectre detection is turned Off below the engine rev set point. Normal operation. The audio volume of all alerts will be automatically muted after four seconds for as long as the signal is detected. All alerts will sound at full volume for as long as the signal is detected. Allows you to calibrate the compass. (see page 18 to calibrate compass) Unit will detect Pop signals. Unit will not detect Pop signals. 8 English Your Detector EasySet Programming Mode VG-2 Detect mode VG-2 Audio mode (not shown if VG-2 detect is Off) Tone Two beeps One beep Two beeps One beep Spectre Detect mode Two beeps One beep Spectre Audio mode (not shown if Spectre detect is Off) Two beeps One beep SmartPower mode Two beeps One beep X Band Detect mode Two beeps One beep K or Ku Band Two beeps Detect mode One beep Set display Dim mode default* Two beeps One beep One beep Restore factory One beep settings Exit program One beep Display/Voice VG-2 Detect On VG-2 Detect Off VG-2 Audio On VG-2 Audio Off Spectre Detect On Spectre Detect Off Spectre Audio On Spectre Audio Off SmartPower On SmartPower Off X Band On Result Unit will detect VG-2 signals. Unit will not detect VG-2 signals. With VG-2 Detect On, the unit will give audible alerts for VG-2 signals. With VG-2 Detect Off, the unit will give only visual alerts for VG-2 signals. Unit will detect Spectre I & IV+ signals. Unit will not detect Spectre I & IV+ signals. With Spectre Audio On, unit will give audible alerts for Spectre signals. With Spectre I Audio Off, unit will give only visual alerts for Spectre I & IV+ signals. SmartPower is On. SmartPower is Off. Unit will detect X Band signals. X Band Off Unit will not detect X Band signals. K or Ku Band On Unit will detect K or Ku Band signals. K or Ku Band Off Unit will not detect K or Ku Band signals. Display Dim Partially dimmed for dusk or night driving. Display Dimmer More dimmed for dusk or night driving. Display Dark Restore Factory Settings Display is Off. Resets user modes and settings to factory default. EXIT PROGRAM Allows you to exit Program mode. * The settings for these user modes can also be changed with the one button method.See description of each user mode (pages 10 and 25) for details. Nothing Comes Close to a Cobra® 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21

EasySet Programming
8
English
Your Detector
Mode
Tone
Display/Voice
Result
Set
IntelliShield
City mode
default*
Two beeps
City X
A single beep sounds when the
signal is first detected.
One beep
City X
beep Off
Audio for all X band alerts are blocked
until signal strength reaches Level 3.
One beep
City X+K
Combines the City X mode with prevention
of K band audio alerts
until signal strength reaches Level 2.
IntelliMute
mode
Two beeps
IntelliMute On
All alerts (except for strobe signals from
emergency vehicles) are automatically
muted below the
engine rev point you set.
One beep
IntelliMute Off
Normal operation.
Set IntelliMute
RPMs
One beep
Set IntelliMute
(see page 15
to set activation
point)
Allows you to set the engine
rev point while using IntelliMute.
Note: Only shown if IntelliMute is Off.
IntelliMute
Pro mode
Two beeps
IntelliMute Pro
On
All radar, VG-2 and Spectre detection is
turned Off below the engine rev set point.
One beep
IntelliMute Pro
Off
Normal operation.
Auto Mute
mode
Two beeps
AutoMute On
The audio volume of all alerts will be
automatically muted after four seconds for as
long as the signal is detected.
One beep
AutoMute Off
All alerts will sound at full volume
for as long as the signal is detected.
Set
Compass
One beep
Set Compass
Allows you to calibrate the compass.
(see page 18 to calibrate compass)
Pop Detect
mode
Two beeps
Pop Detect On
Unit will detect Pop signals.
One beep
Pop Detect Off
Unit will not detect Pop signals.
This EasySet programming menu lists all of the modes and settings you can
choose from after you have entered Program mode as described on page 7.
Mode
Tone
Display/Voice
Result
VG-2 Detect
mode
Two beeps
VG-2 Detect On
Unit will detect VG-2 signals.
One beep
VG-2 Detect Off
Unit will not detect VG-2 signals.
VG-2 Audio
mode (not
shown if VG-2
detect is Off)
Two beeps
VG-2 Audio On
With VG-2 Detect On, the unit will give
audible alerts for VG-2 signals.
One beep
VG-2 Audio Off
With VG-2 Detect Off, the unit will give
only visual alerts for VG-2 signals.
Spectre
Detect mode
Two beeps
Spectre
Detect On
Unit will detect Spectre I & IV+ signals.
One beep
Spectre
Detect Off
Unit will not detect Spectre I & IV+
signals.
Spectre
Audio
mode (not
shown
if Spectre
detect is Off)
Two beeps
Spectre Audio
On
With Spectre Audio On, unit will give
audible alerts for Spectre signals.
One beep
Spectre Audio
Off
With Spectre I Audio Off, unit will give only
visual alerts for Spectre I & IV+
signals.
SmartPower
mode
Two beeps
SmartPower On
SmartPower is On.
One beep
SmartPower Off
SmartPower is Off.
X Band
Detect mode
Two beeps
X Band On
Unit will detect X Band signals.
One beep
X Band Off
Unit will not detect X Band signals.
K or Ku Band
Detect mode
Two beeps
K or Ku Band On
Unit will detect K or Ku Band signals.
One beep
K or Ku Band Off
Unit will not detect K or Ku Band signals.
Set display
Dim mode
default*
Two beeps
Display Dim
Partially dimmed for dusk or night driving.
One beep
Display Dimmer
More dimmed for dusk or night driving.
One beep
Display Dark
Display is Off.
Restore factory
settings
One beep
Restore Factory
Settings
Resets user modes and settings to factory
default.
Exit program
One beep
EXIT PROGRAM
Allows you to exit Program mode.
* The settings for these user modes can also be changed with
the one button method.See description of each user mode
(pages 10 and 25) for details.
Nothing
Comes Close to a Cobra
®
9
Your Detector
EasySet Programming