Cobra XRS 9770 XRS 9770 Manual - Page 8

IntelliShield Highway/City Modes - from

Page 8 highlights

Your Detector Settings Settings • IntelliShield Highway/City Modes Your detector is equipped with IntelliShield false signal rejection technology which consists of a Highway mode and three different levels of City modes: City X, City X Beep Off and City X+K. City X mode sounds a single beep when the signal is first detected. City X Beep Off mode prevents all X band audio alerts until the signal strength reaches Level 3. City X+K mode combines the City X mode with prevention of K band audio alerts until the signal strength reads Level 2. This will reduce false alerts while you are driving in or near urban areas where there are many sources for conflicting X or K band signals such as microwave towers and automatic door openers. The factory setting is Highway. The factory City mode default setting is City X. Set/City Button Press and release To Change From Highway Mode to City Mode Press and release Tone the Set/City button. One beep Visual Display c appears in the display Voice City X or City X Beep Off or City X, K City Mode NW c NOTE When you change to City mode, the unit will enter whichever city default mode is set at the time. To Change From City Mode Back to Highway Mode Press and release Tone the Set/City button again. Two beeps Highway Mode Visual Display h appears in the display Voice Highway NW h 10 English Your Detector Settings Setting City Default You can set the default level for City mode (City X, City X Beep Off and City X+K) either in Program mode or directly using the Set/City button. Set/City Button Press and hold City X City X+K Press and hold the Set/City button City X Beep Off To Set the City Mode Default Directly Using the Set/City Button Press and hold the Set/ City button. Tone or Voice One beep each time the display cycles Visual Display Cycles - see chart above Release the Set/City None button to select the current display as default. City X Beep Off, City X+K or City X To Set the City Mode Default Using Program Mode (See Page 7 For Instructions on Using Program Mode) In Program mode, go to City. Tone One beep Visual Display City X Beep Off One beep City X+K Two beeps City X City X Beep Off City X+K City X City X+K Voice City X Beep Off City X, K City X City X City X Beep Off Nothing Comes Close to a Cobra® 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21

Settings
Your Detector
Nothing
Comes Close to a Cobra
®
11
Settings
Your Detector
10
English
Settings
IntelliShield Highway/City Modes
Your detector is equipped with
IntelliShield
false signal rejection technology which
consists of a Highway mode and three different levels of City modes: City X, City
X Beep Off and City X+K.
City X
mode sounds a single beep when the signal is
first detected.
City X Beep Off
mode prevents all X band audio alerts until the
signal strength reaches Level 3.
City X+K
mode combines the City X mode with
prevention of K band audio alerts until the signal strength reads Level 2. This will
reduce false alerts while you are driving in or near urban areas where there are
many sources for conflicting X or K band signals such as microwave towers and
automatic door openers. The factory setting is Highway. The factory City mode
default setting is City X.
Setting City Default
You can set the default level for City mode (
City X, City X Beep Off and
City X+K
) either in Program mode or directly using the
Set/City
button.
City Mode
N W
c
To Change From Highway Mode to City Mode
Press and release
the
Set/City
button.
Tone
Visual Display
Voice
One beep
c
appears in
the display
City X
or
City X Beep Off
or
City X, K
To Change From City Mode Back to Highway Mode
Press and release
the
Set/City
button again.
Tone
Visual Display
Voice
Two beeps
h
appears in
the display
Highway
To Set the City Mode Default Directly Using the Set/City Button
Press and hold the
Set/
City
button.
Tone or Voice
Visual Display
One beep each time the
display cycles
Cycles – see chart above
Release the
Set/City
button to select the
current display as default.
None
City X Beep Off
,
City X+K
or
City X
To Set the City Mode Default Using Program Mode
(See Page 7 For Instructions on Using Program Mode)
In Program mode,
go to City.
Tone
Visual Display
Voice
One beep
City X Beep Off
City X Beep Off
One beep
City X+K
City X, K
Two beeps
City X
City X
Press and
hold the
Set/City
button
City
X+K
City X
City X
Beep Off
NOTE
When you change to City mode, the unit will enter
whichever city default mode is set at the time.
City X Beep Off
City X
Beep Off
City X+K
City X+K
City X
City X
Highway Mode
N W
h
Set/City Button
Press and release
Set/City Button
Press and hold