Home » Compaq Manuals » Desktops » Compaq 470007-802 » Manual Viewer

Compaq 470007-802 Deskpro EN Series of Personal Computers Maintenance and Serv - Page 40

Feet Installation, 4.4 Logo Plate

Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

4.3 Feet Installation Four (4) rubber feet are mounted to the chassis, as shown below. No parts have to be removed to access the feet. The replacement feet have an adhesive surface and are shipped with a protective backing in place. Remove the backing from the feet before installation. If necessary, remove the old feet and remove any adhesive residue from the chassis. 4.4 Logo Plate Grasp the open side of the logo plate (left side if a desktop, bottom if a minitower) and pull outward 2. To install a new logo plate, align the guide pins in the slots 1, then press into place. ✎ When replacing the logo plate, ensure that the alignment pins are properly placed in the front bezel before pressing the logo plate into position. Compaq Deskpro EN Series of Personal Computers 4-3

Section	Page
Maintenance & Service Guide	1
Addendum #1 to Deskpro EN Maintenance & Service Guide	2
NOTICE	7
CONTENTS	8
ABOUT THIS GUIDE	11
Symbols and Conventions	11
Technician Notes	11
Locating Additional Information	12
PRODUCT DESCRIPTION	13
1.1 Model Overview	14
1.2 System Design	14
1.3 Preinstalled Software	15
1.4 Computer Features	16
1.5 Serial Number Location	19
1.6 Locating Additional Information	20
SPARE PARTS	21
2.1 System Unit	22
2.2 Mass Storage Devices	23
2.3 Cables	24
2.4 Standard, Memory, and Expansion Boards	25
2.5 Keyboards	26
2.6 Miscellaneous Screw Kit	27
2.7 Miscellaneous Plastics Kit	28
2.8 Miscellaneous Parts	29
2.9 Shipping Boxes	30
2.10 Documentation and Software	30
REMOVAL & REPLACEMENT PRELIMINARIES	31
3.1 Electrostatic Discharge Information	31
3.2 Routine Care	34
3.3 Service Considerations	36
REMOVAL AND REPLACEMENT PROCEDURES	38
4.1 Disassembly Sequence Chart	38
4.2 Disassembly Preparation	39
4.3 Feet Installation	40
4.4 Logo Plate	40
4.5 Cable Lock	41
4.6 Access Panel	42
4.7 Front Bezel	43
4.8 Power Button	44
4.9 Subpanel and Bezel Blanks	45
4.10 Power Switch	46
4.11 Mass Storage Devices	47
4.12 Removing the Drivelocks	55
4.13 Expansion Boards	58
4.14 Board Guide	62
4.15 Internal Speaker	63
4.16 System Memory	64
4.17 Graphics Cards	66
4.18 Processor	73
4.19 System Board	74
4.20 Battery	75
4.21 Chassis Fan Assembly	76
4.22 Power Supply	77
4.23 Converting a Desktop to a Minitower	78
4.24 Converting a Minitower to a Desktop	80
CONNECTORS AND JUMPERS	83
5.1 System Board	83
5.2 Hard Drive Jumper Settings	86
SPECIFICATIONS	88
6.1 Specifications	88
6.2 Drives	93
6.3 Compaq Keyboards	96
6.4 2-Button Mouse	96
6.5 Supported Graphics Resolutions	97
SERVICE NOTES	98

Match case Limit results 1 per page

Compaq Deskpro EN Series of Personal Computers

4-3

4.3

Feet Installation

Four (4) rubber feet are mounted to the chassis, as shown below. No parts have to be

removed to access the feet. The replacement feet have an adhesive surface and are shipped

with a protective backing in place. Remove the backing from the feet before installation.

If necessary, remove the old feet and remove any adhesive residue from the chassis.

4.4

Logo Plate

Grasp the open side of the logo plate (left side if a desktop, bottom if a minitower) and

pull outward

To install a new logo plate, align the guide pins in the slots

, then press into place.

✎

When replacing the logo plate, ensure that the alignment pins are properly placed

in the front bezel before pressing the logo plate into position.