Compaq 470007-802 Deskpro EN Series of Personal Computers Maintenance and Serv - Page 52

Reinstall the subpanel and the front bezel., Remove the bezel blank from the subpanel

Get Compaq 470007-802 - Deskpro EN - 256 MB RAM PDF manuals and user guides View all Compaq 470007-802 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

6. While the drivelock is held in the unlatched position, remove the drive from the drive bay. 7. Remove the four guide screws from the drive 1. To install a new drive: 1. Install two guide screws on each side of the replacement drive 1. 2. Ensure that the guide screws line up with the guide slots 2, then slide the drive into the drive bay until it snaps into place. 3. Connect the power and signal cables to the back of the drive. 4. Remove the bezel blank from the subpanel, if necessary (Section 4.9). 5. Reinstall the subpanel and the front bezel. The system automatically recognizes hard drives sold by Compaq (or any other plug and play hard drive) and will automatically reconfigure the computer. If you installed a thirdparty hard drive, or one that is not a plug and play device, you must run Computer Setup to reconfigure the computer. Compaq Deskpro EN Series of Personal Computers 4-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
Compaq Deskpro EN Series of Personal Computers
4-15
6.
While the drivelock is held in the unlatched position, remove the drive from the
drive bay.
7.
Remove the four guide screws from the drive
1
.
To install a new drive:
1.
Install two guide screws on each side of the replacement drive
1
.
2.
Ensure that the guide screws line up with the guide slots
2
, then slide the drive into the
drive bay until it snaps into place.
3.
Connect the power and signal cables to the back of the drive.
4.
Remove the bezel blank from the subpanel, if necessary (Section 4.9).
5.
Reinstall the subpanel and the front bezel.
The system automatically recognizes hard drives sold by Compaq (or any other plug and
play hard drive) and will automatically reconfigure the computer. If you installed a third-
party hard drive, or one that is not a plug and play device, you must run Computer Setup
to reconfigure the computer.