Compaq Armada 7300 33.6Kbps Modem Commands for Armada 7000 Family of Personal - Page 42

Lost Carrier to Hang-Up Delay S10

Get Compaq Armada 7300 - Notebook PC PDF manuals and user guides View all Compaq Armada 7300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

: 3 +,7( $3(5 (cont.) . . . Lost Carrier to Hang-Up Delay (S10) . . . This register sets the length of time, in tenths of a second, that the modem waits before hanging up after a loss of carrier. This allows for a temporary carrier loss without causing . the local modem to disconnect. . . Range: 1-255 tenths of a second . . (Default): 14 (1.4 seconds) . . . DTMF Tone Duration (S11) . This register sets the duration of tones and spacing in DTMF dialing. . . Range: 50-255 milliseconds . . (Default): 95 (95 milliseconds) . . . Escape Code Guard Time (S12) . This register determines the minimum idle period before and after the entry of the escape . code sequence. Also, it defines the maximum period, in fiftieths of a second, allowed . between consecutive asynchronous escape characters S2 for the escape sequence to be . . considered valid. If this register is set to 0, the guard time of the escape sequence is disabled. . . Range: 0 or 20-255 (1/50 of a second or 0.02 seconds) . . (Default): 50 (1 second) . . Test Timer (S18) . . . This register sets the length of time, in seconds, that the modem conducts a test (commanded by &Tn) before returning to the command mode. When this register value is zero, the test . will not automatically terminate. The test must be terminated from the command mode by . issuing the &T0 or H command. . . . Range: 0-255 seconds . (Default): 0 . . . Response to DTR Change (S25) . This register responds to changes to the DTR. The increment is 10 milliseconds. If &D1 or . &D2 is selected, a change in DTR shorter than the S25 time is ignored. If &D3 is selected, . . any on-to-off transition of DTR causes a hard reset. . . Range: 0-255 . . (Default): 5 (50 milliseconds) . . Disconnect Inactivity Timer (S30) . . . This register sets the length of time, in minutes, that the modem will stay online before disconnecting when no data is sent or received. If this register is set to 0, the disconnect . inactivity timer is disabled. . . Range: 0-90 minutes . . . 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
(cont.)
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Lost Carrier to Hang-Up Delay (S10)
This register sets the length of time, in tenths of a second, that the modem waits before
hanging up after a loss of carrier. This allows for a temporary carrier loss without causing
the local modem to disconnect.
Range:
1-255 tenths of a second
(Default)
:
14 (1.4 seconds)
DTMF Tone Duration (S11)
This register sets the duration of tones and spacing in DTMF dialing.
Range:
50-255 milliseconds
(Default)
:
95 (95 milliseconds)
Escape Code Guard Time (S12)
This register determines the minimum idle period before and after the entry of the escape
code sequence. Also, it defines the maximum period, in fiftieths of a second, allowed
between consecutive asynchronous escape characters S2 for the escape sequence to be
considered valid. If this register is set to 0, the guard time of the escape sequence is disabled.
Range:
0 or 20-255
(1/50 of a second or 0.02 seconds)
(Default)
:
50 (1 second)
Test Timer (S18)
This register sets the length of time, in seconds, that the modem conducts a test (commanded
by &Tn) before returning to the command mode. When this register value is zero, the test
will not automatically terminate. The test must be terminated from the command mode by
issuing the &T0 or H command.
Range:
0-255 seconds
(Default)
:
0
Response to DTR Change (S25)
This register responds to changes to the DTR. The increment is 10 milliseconds. If &D1 or
&D2 is selected, a change in DTR shorter than the S25 time is ignored. If &D3 is selected,
any on-to-off transition of DTR causes a hard reset.
Range:
0-255
(Default)
:
5 (50 milliseconds)
Disconnect Inactivity Timer (S30)
This register sets the length of time, in minutes, that the modem will stay online before
disconnecting when no data is sent or received. If this register is set to 0, the disconnect
inactivity timer is disabled.
Range:
0-90 minutes