D-Link DGS-6600-48TS CLI Guide
D-Link DGS-6600-48TS Manual
 |
View all D-Link DGS-6600-48TS manuals
Add to My Manuals
Save this manual to your list of manuals |
D-Link DGS-6600-48TS manual content summary:
- D-Link DGS-6600-48TS | CLI Guide - Page 1
0.9.3 - D-Link DGS-6600-48TS | CLI Guide - Page 2
- DGS-6604 CLI Reference Guide Software Release 2.10.011 Date: March 1, 2012 Copyright Statement D-Link Corporation © 2011-2012 All rights reserved. Without our written permission this document may not be excerpted, reproduced, transmitted, or otherwise in all or part by any party by any means. ii - D-Link DGS-6600-48TS | CLI Guide - Page 3
the reference manual. Other Documentation The documents below are a further source of information in regards to configuring and troubleshooting the switch. All the documents are available for download from D-Links web site www.d-link.com. • DGS-6600 Series Quick Installation Guide • DGS-6600 Series - D-Link DGS-6600-48TS | CLI Guide - Page 4
and Cautions Below are examples of the 3 types of indicators used in this manual. When administering your switch using the information in this document, you should pay and tells you how to avoid the problem CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. iv - D-Link DGS-6600-48TS | CLI Guide - Page 5
entering and issuing the command. The form conventions are described in the table shown under the section "Conventions" on page iv of this guide. • Syntax Description - A table where each row describes the optional or required arguments, and their use, that can be issued with the command. • Default - D-Link DGS-6600-48TS | CLI Guide - Page 6
- • User EXEC mode • Privileged EXEC mode • Global Configuration mode All other sub-configuration modes can be accessed via global configuration mode. When a user logs in to the Switch, the privilege level of the user determines the command mode the user will enter after initially logging in. The - D-Link DGS-6600-48TS | CLI Guide - Page 7
- Note: Not all configuration modes are listed in the above figure. For example, in global configuration mode, enter "router ospf" to enter OSPF router configuration mode The following table briefly lists the available command modes. Only the basic command modes and some of the sub-configuration - D-Link DGS-6600-48TS | CLI Guide - Page 8
in as an advanced user in privileged EXEC mode and uses the disable command to return to user EXEC mode at advanced user level: DGS-6604:15#disable DGS-6604:2> Privileged EXEC Mode at Power User Level Users logged into the Switch in privileged EXEC mode at this level can change both - D-Link DGS-6600-48TS | CLI Guide - Page 9
- User Access Verification Username: power-user Password: DGS-6604 Chassis-based High-Speed Switch Command Line Interface Firmware: 2.00.001 Copyright (c) 2010 D-Link Corporation. All rights reserved. DGS-6604:12# In the following example, the user enters the enable privilege LEVEL command in user - D-Link DGS-6600-48TS | CLI Guide - Page 10
-6604:15#configure terminal DGS-6604:15(config)# The exit command is used to exit global configuration mode and return to privileged EXEC mode. The procedures to enter the different sub-configuration modes can be found in the related chapters in this Configuration Guide. The command modes are used - D-Link DGS-6600-48TS | CLI Guide - Page 11
DGS-6604 m Command Listing by Feature 802.1x AAA dot1x auth-mode - 169 dot1x auth-protocol - 170 dot1x control-direction - 171 dot1x default - - 599 aaa authentication - 27 aaa authorization - 29 aaa group server - 30 server - 541 show aaa - 572 show aaa group server - 575 CLI Reference Guide 1 - D-Link DGS-6600-48TS | CLI Guide - Page 12
DGS-6604 m Access Control Lists Access Management ip access-group - 224 ip access-list - 225 ipv6 access-group - 327 ipv6 access 124 disable - 159 enable - 186 enable password - 187 end - 188 exit - 189 help - 216 ip http server - 264 ip http service-port - 265 ip telnet server - 323 CLI Reference - D-Link DGS-6600-48TS | CLI Guide - Page 13
DGS-6604 m Basic IPv4 Basic IPv6 ip telnet service-port - 324 ip trusted-host - 325 login - 406 logout - 407 password encryption - 471 show history - 609 show ip trusted-host - - 150 ipv6 address - 330 ipv6 enable - 340 ipv6 hop-limit - 341 ipv6 nd managed-config-flag - 342 CLI Reference Guide 3 - D-Link DGS-6600-48TS | CLI Guide - Page 14
DGS-6604 m Basic Switch BGP ipv6 nd other-config-flag - 343 ipv6 nd prefix - 344 ipv6 nd ra-interval - 345 ipv6 nd ra-lifetime - 346 default ipv4-unicast - 73 bgp default local-preference - 74 bgp deterministic-med - 75 bgp enforce-first-as - 76 bgp log-neighbor-changes - 77 CLI Reference Guide 4 - D-Link DGS-6600-48TS | CLI Guide - Page 15
DGS-6604 m bgp router-id - 78 clear ip bgp - 95 clear ip bgp peer-group - 97 default-information originate (BGP) - 146 ip dhcp screening ports 455 network (BGP) - 460 redistribute - 517 router bgp - 532 set as-path - 549 set community - 550 set origin - 564 set weight - 565 CLI Reference Guide 5 - D-Link DGS-6600-48TS | CLI Guide - Page 16
DGS-6604 m Broadcast Storm Chassis Digital Diagnostic Monitoring (DDM) show ip as-path access-list - 613 show ip bgp - 614 show ip bgp community-list - bias-current - 142 ddm tx-power - 143 ddm rx-power - 144 show ddm - 590 show ddm status - 591 show ddm configuration - 592 CLI Reference Guide 6 - D-Link DGS-6600-48TS | CLI Guide - Page 17
DGS-6604 m Dynamic ARP Inspection ip arp inspection trust - 237 ip arp inspection validate - 238 ip arp inspection vlan - 240 show ip arp inspection show ipv6 dhcp relay interface - 703 accept dhcp client-identifier - 31 accept dhcp relay-agent - 32 based-on client-id - 59 CLI Reference Guide 7 - D-Link DGS-6600-48TS | CLI Guide - Page 18
DGS-6604 m based-on c-vid - 60 based-on interface-ip-address - 61 based-on mac- - 252 lease - 381 netbios node-type - 456 netbios scope-id - 457 netbios wins-server - 458 next-server - 462 service dhcp - 543 show ip dhcp binding - 623 show ip dhcp conflict - 625 show ip dhcp pool - 626 show ip dhcp - D-Link DGS-6600-48TS | CLI Guide - Page 19
DGS-6604 m subnet-mask - 886 DHCP Server Screening/ Client Filtering ip dhcp screening ports - 230 ip dhcp screening - 231 ip dhcp screening trap-log - 635 show ip dvmrp neighbor - 636 show ip dvmrp prune - 639 show ip dvmrp route - 640 ERPS erps - 190 erps domain - 191 CLI Reference Guide 9 - D-Link DGS-6600-48TS | CLI Guide - Page 20
DGS-6604 m Errdisable File System GVRP IGMP erpi enable - 192 erpi type - 193 erpi raps-vlan - 195 erpi ring-mel - 196 erpi ring-port - -creation - 213 gvrp forbidden - 214 gvrp timer - 215 show gvrp configuration - 606 show gvrp statistics - 608 ip igmp access-group - 266 CLI Reference Guide 10 - D-Link DGS-6600-48TS | CLI Guide - Page 21
DGS-6604 m IGMP Snooping Interface IP Utility IP Multicast ip igmp last-member-query-interval - 268 ip igmp query-interval - 269 ip igmp 610 show interface status err-disabled - 612 ping - 480 traceroute - 906 ip mroute - 281 ip multicast-routing - 285 show ip mroute - 654 CLI Reference Guide 11 - D-Link DGS-6600-48TS | CLI Guide - Page 22
DGS-6604 m IPv6 Protocol Independent IP Source Guard IPv6 Tunnel Jumbo Frame L2 FDB ipv6 route - 362 ipv6 unicast-routing long-prefix - address-table static - 417 multicast filtering-mode - 440 show mac address-table - 730 show mac address-table aging destination-hit - 732 CLI Reference Guide 12 - D-Link DGS-6600-48TS | CLI Guide - Page 23
DGS-6604 m LACP lldp-med show mac address-table aging-time - 733 show multicast filtering-mode - 737 channel-group - 84 lacp port-priority - lldp tx-interval - 400 show lldp - 814 show lldp interface - 816 show lldp local interface - 818 show lldp management-address - 823 CLI Reference Guide 13 - D-Link DGS-6600-48TS | CLI Guide - Page 24
DGS-6604 m Loopback Detection Management Port Mirror MSTP show lldp neighbor interface - 825 show lldp statistics - 831 show lldp statistics interface - 735 instance - 220 name - 441 revision - 528 show spanning-tree mst - 759 spanning-tree mst (cost | port-priority) - 867 CLI Reference Guide 14 - D-Link DGS-6600-48TS | CLI Guide - Page 25
DGS-6604 m Network Load Balancing OSPFv2 spanning-tree 417 area default-cost - 39 area nssa - 41 area range - 43 area stub - 45 area virtual-link - 47 auto-cost reference-bandwidth - 55 clear ip ospf - 104 default-information originate (BGP) - 146 ospf transmit-delay - 295 CLI Reference Guide 15 - D-Link DGS-6600-48TS | CLI Guide - Page 26
DGS-6604 m OSPFv3 ip ospf mtu-ignore - 296 network area - 461 passive-interface - 463 674 show ip ospf neighbor - 676 show ip ospf virtual-links - 677 area default-cost (IPv6) - 40 area range (IPv6) - 44 area stub (IPv6) - 46 area virtual-link (IPv6) - 51 auto-cost reference-bandwidth (IPv6) - - D-Link DGS-6600-48TS | CLI Guide - Page 27
DGS-6604 m Password Recovery PIM ipv6 ospf cost - 351 ipv6 ospf dead-interval 712 show ipv6 ospf interface - 713 show ipv6 ospf neighbor - 714 show ipv6 ospf route - 715 show ipv6 ospf virtual-links - 716 show ipv6 protocols - 717 password recovery - 467 ip pim - 297 ip pim accept-register - 298 ip - D-Link DGS-6600-48TS | CLI Guide - Page 28
DGS-6604 m POE Policy-based Route Port Security ip pim join-prune-interval - 302 pim rp mapping - 687 show ip pim rp-hash - 688 poe port priority - 482 poe port description - 483 poe service-policy - 484 poe power-inline - 485 show poe power system - 833 show poe power-inline - 835 ip policy route- - D-Link DGS-6600-48TS | CLI Guide - Page 29
DGS-6604 m Power Saving Protocol Independent QoS power-saving - 500 show power-saving - 741 distance - 160 ip route - 319 ip route multi-path - 320 maximum- mutation - 510 qos map cos-color - 511 qos map dscp-color - 512 qos map dscp-cos - 513 qos map dscp-mutation - 514 CLI Reference Guide 19 - D-Link DGS-6600-48TS | CLI Guide - Page 30
Preface qos trust - 515 service-policy - 544 set - 547 show class-map - 584 show policy-map - 738 show qos aggregate-policer - 742 show qos interface -chain - 313 ip rip authentication mode - 315 ip rip receive version - 316 ip rip send version - 317 CLI Reference Guide - Preliminary Draft 20 - D-Link DGS-6600-48TS | CLI Guide - Page 31
) - 443 passive-interface (RIP IPv6) - 466 redistribute (RIP IPv6) - 524 router ipv6 rip - 535 show ipv6 protocols - 717 show ipv6 rip database - 719 CLI Reference Guide - Preliminary Draft 21 - D-Link DGS-6600-48TS | CLI Guide - Page 32
DGS-6604 m RMON Route Map Safeguard sFlow show ipv6 rip interface - 720 timers basic - 902 rmon statistics - 529 match ip address - 425 match 587 show cpu-protect sub-interface - 589 sflow - 566 sflow receiver - 567 sflow sampler - 569 sflow poller - 571 show sflow - 812 CLI Reference Guide 22 - D-Link DGS-6600-48TS | CLI Guide - Page 33
DGS-6604 m SNMP Management SSH STP show snmp - 750 show snmp-server - 753 show snmp user - 754 snmp-server - 841 snmp-server - 757 spanning-tree ( Global configuration ) - 859 spanning-tree (Interface configuration) - 860 spanning-tree (timers) - 861 spanning-tree cost - 862 CLI Reference Guide 23 - D-Link DGS-6600-48TS | CLI Guide - Page 34
DGS-6604 m Switch Port Syslog System File Management spanning-tree fast-forwarding - 863 spanning-tree guard root - 864 spanning-tree link-type - 865 spanning-tree mode - 866 spanning-tree port-priority - show boot - 579 show running-config - 749 show startup-config - 763 CLI Reference Guide 24 - D-Link DGS-6600-48TS | CLI Guide - Page 35
DGS-6604 m Time and SNTP Traffic Segmentation VLAN VRRP clock set - 117 clock summer-time - 118 clock timezone - 120 show clock - 585 show sntp - 756 allowed-vlan - 912 vlan - 919 vlan name - 921 show vrrp - 785 show vrrp brief - 788 vrrp critical-ip - 935 vrrp ip - 937 CLI Reference Guide 25 - D-Link DGS-6600-48TS | CLI Guide - Page 36
DGS-6604 m Voice Vlan vrrp preempt - 938 vrrp priority - 940 vrrp shutdown - 942 vrrp timers advertise - 943 show vlan voice-vlan - 801 switchport voice-vlan state - 840 voice-vlan - 931 voice-vlan cos - 932 voice-vlan oui - 933 CLI Reference Guide 26 - D-Link DGS-6600-48TS | CLI Guide - Page 37
DGS-6604 m aaa authentication aaA a authentication Use this command to enable the AAA authentication function (console, telnet, ssh or http) using implied. If no application is specified, all applications (console, telnet, ssh, or http) are assumed valid for system access. CLI Reference Guide 27 - D-Link DGS-6600-48TS | CLI Guide - Page 38
DGS-6604 m Example aaa authentication Multiple methods for the login/enable authentication per application can be specified. The new setting will (config)# aaa authentication login group group2 local Switch(config)# Verify the settings by entering the show aaa command. CLI Reference Guide 28 - D-Link DGS-6600-48TS | CLI Guide - Page 39
DGS-6604 m aaa authorization aaa authorization Use this command to enable the authorization function. Use the no form of the command to : Switch# configure terminal Switch(config)# aaa authorization Verify the settings by entering the show system protocol-state command. CLI Reference Guide 29 - D-Link DGS-6600-48TS | CLI Guide - Page 40
DGS-6604 m aaa group server aaa group server Use the aaa group server command to enter AAA group server mode and identify AAA server groups .10.101 key 12345678 Switch(config-aaa-group-server)# end Switch# Verify the settings by entering the show aaa group server command. CLI Reference Guide 30 - D-Link DGS-6600-48TS | CLI Guide - Page 41
DGS-6604 m accept dhcp client-identifier matches the hardware type and client hardware address. If the values match, the DHCP server provides service to the client. If the values do not match, the DHCP server does not respond to dhcp client-identifier switch(config-dhcp)# CLI Reference Guide 31 - D-Link DGS-6600-48TS | CLI Guide - Page 42
DGS-6604 m accept dhcp relay-agent accept dhcp relay-agent To accept relay agent information use the accept dhcp relay-agent command, use # configure terminal switch(config)# ip dhcp pool pool1 switch(config-dhcp)# no accept dhcp relay-agent remote-id switch(config-dhcp)# CLI Reference Guide 32 - D-Link DGS-6600-48TS | CLI Guide - Page 43
DGS-6604 m acceptable-frame acceptable-frame Use the acceptable-frame interface command to set the acceptable frame type of a port for IEEE )# interface eth3.1 Switch(config-if)# acceptable-frame tagged-only Verify the settings by entering the show vlan interface command. CLI Reference Guide 33 - D-Link DGS-6600-48TS | CLI Guide - Page 44
DGS-6604 m accept-lifetime accept-lifetime The accept-lifetime command is used to set a time period when an authentication key on a key chain RIP) Version 2 uses key chains. Specify a start time value and one of the following values: infinite, end-time, or duration seconds. CLI Reference Guide 34 - D-Link DGS-6600-48TS | CLI Guide - Page 45
DGS-6604 m Example accept-lifetime The following example configures a key chain named chain1. Key 1 named "forkey1string" will be accepted from 1:30 p.m. to 3: -keychain-key)# exit Switch(config-keychain)# exit Verify the settings by entering the show ip key-chain command. CLI Reference Guide 35 - D-Link DGS-6600-48TS | CLI Guide - Page 46
DGS-6604 m access vlan access vlan Use the access vlan interface configuration command to specify the access VLAN for the interface. Use Switch(config)# interface eth3.1 Switch(config-if)# access vlan 1000 Verify the settings by entering the show vlan interface command. CLI Reference Guide 36 - D-Link DGS-6600-48TS | CLI Guide - Page 47
DGS-6604 m address-family ipv4 address-family ipv4 Use this unicast address prefixes. Default Command Mode Usage Guideline Example Unicast prefix support is enabled by default when this command is entered without any Switch(config-router-af)# exit Switch(config-router)# CLI Reference Guide 37 - D-Link DGS-6600-48TS | CLI Guide - Page 48
DGS-6604 m aggregate-address aggregate-address Use this command to configure BGP aggregate entries. Use the no form of the command to the more specific route 172.10.0.0: Switch(config)# router bgp 65534 Switch(config-router)# aggregate-address 172.0.0.0/8 summary-only CLI Reference Guide 38 - D-Link DGS-6600-48TS | CLI Guide - Page 49
DGS-6604 m area default-cost area default-cost The cost of the default summary route sent into a not-so-stubby area (NSSA) or a stub )# router ospf Switch (config-router)# area 10.0.0.0 default-cost 20 Verify the settings by entering the show ip ospf interface command. CLI Reference Guide 39 - D-Link DGS-6600-48TS | CLI Guide - Page 50
DGS-6604 m area default-cost (IPv6) area default-cost (IPv6) To set the summary-default cost of a stub area, use the area Switch # configure terminal Switch (config) # router ipv6 ospf Switch (config-router) # area 1 stub Switch (config-router) # area 1 default-cost 10 CLI Reference Guide 40 - D-Link DGS-6600-48TS | CLI Guide - Page 51
DGS-6604 m area nssa area nssa Use this command to define an area as an NSSA (not-so-stubby) area. Use the no nssa command to remove the NSSA designation. Note: For OSPFv3 this command is not supported (Optional) For OSPF, the external link type associated with the default route advertised Guide 41 - D-Link DGS-6600-48TS | CLI Guide - Page 52
DGS-6604 m Example area nssa An NSSA allows external routes to be advertised to the area in type 7 link state advertisement (LSA). These routes are then leaked into other areas. Although, the external )# area 1 nssa Verify the settings by entering the show ip ospf command. CLI Reference Guide 42 - D-Link DGS-6600-48TS | CLI Guide - Page 53
DGS-6604 m area range area range Use this range. advertise (Optional) Sets the status to advertise and generate a Type 3 summary link-state advertisement (LSA) for the specified address range. not-advertise (Optional) Sets the by entering the show ip ospf command. CLI Reference Guide 43 - D-Link DGS-6600-48TS | CLI Guide - Page 54
DGS-6604 m area range (IPv6) area range (IPv6) To prefix length advertise (Optional) Advertise and generate a Type 3 Inter-Area Prefix link-state advertisement (LSA) for the specified address range. not- advertise (Optional) -router)# area 1 range 2001:0DB8:0:1::/64 CLI Reference Guide 44 - D-Link DGS-6600-48TS | CLI Guide - Page 55
DGS-6604 m area stub area stub Use this command to Default Command Mode Usage Guideline Example Stub areas are not configured. Summary link advertisements are sent into the stub area. Router configuration When employed, this settings by entering the show ip ospf command. CLI Reference Guide 45 - D-Link DGS-6600-48TS | CLI Guide - Page 56
DGS-6604 m area stub (IPv6) area stub an IPv4 address. no-summary (Optional) Prevent an ABR from sending summary link advertisements into the stub area. Default Command Mode Usage Guideline Examples Disabled Router 20.0.1.10 Switch (config-router)# area 1 stub CLI Reference Guide 46 - D-Link DGS-6600-48TS | CLI Guide - Page 57
DGS-6604 m area virtual-link area virtual-link Use this command to configure a link between two backbone areas that are physically separated through other non-backbone area. Use the no area virtuallink command to remove a virtual link. area AREA-ID virtual-link value. CLI Reference Guide 47 - D-Link DGS-6600-48TS | CLI Guide - Page 58
, configure a password for virtual link using the area virtual-link authentication-key command. If the area virtual-link authentication message-digest command is used, configure the message-digest key for the virtual link using area virtual-link message-digest-key command. CLI Reference Guide 48 - D-Link DGS-6600-48TS | CLI Guide - Page 59
DGS-6604 m area virtual-link The password created by the area virtual-link authentication-key command is used as a "key" that is inserted directly into the OSPF header when the switch system software originates routing protocol packets over this virtual link. Usually, one key per interface (or - D-Link DGS-6600-48TS | CLI Guide - Page 60
terminal Switch(config)# router ospf 1 Switch(config-router)# area virtual-link 192.168.255.1 authentication-key yourpass Switch(config-router)# area 1 virtual-link 192.168.255.1 authentication Verify the settings by entering the show ip ospf virtual-links command. CLI Reference Guide 50 - D-Link DGS-6600-48TS | CLI Guide - Page 61
DGS-6604 m area virtual-link (IPv6) area virtual-link (IPv6) To define an OSPF virtual link, use the area virtual-link command with the optional parameters. To remove a virtual link, use the no form of this command. area AREA-ID virtual-link associated with the virtual link neighbor. This can link - D-Link DGS-6600-48TS | CLI Guide - Page 62
the IPv6 prefix of the remote router. The following example establishes a virtual link with default values for all optional parameters. Switch > enable Switch # configure terminal Switch (config) # router ipv6 ospf Switch (config-router)# area 1 virtual-link 192.168.255.1 CLI Reference Guide 52 - D-Link DGS-6600-48TS | CLI Guide - Page 63
DGS-6604 m arp arp Use this command to add a static in four-part dotted decimal format corresponding to the local data-link address. HARDWAREADDRESS Local data-link Media Access (MAC) address (a 48-bit address). Default Command settings by entering the show arp command. CLI Reference Guide 53 - D-Link DGS-6600-48TS | CLI Guide - Page 64
DGS-6604 m arp timeout arp timeout Use the arp timeout command to set the ARP aging time for the ARP table. arp timeout SECONDS default setting: Switch(config)# interface vlan1 Switch(config-if)# arp timeout 12000 Verify the settings by using show ip interface command CLI Reference Guide 54 - D-Link DGS-6600-48TS | CLI Guide - Page 65
DGS-6604 m auto-cost reference-bandwidth auto- bandwidth links. For multiple links with high bandwidth, specify a larger reference bandwidth value to differentiate costs on those links. Before the cost is changed to the manual configuration show ip protocol ospf command. CLI Reference Guide 55 - D-Link DGS-6600-48TS | CLI Guide - Page 66
DGS-6604 m auto-cost reference-bandwidth (IPv6) auto-cost reference-bandwidth (IPv6) To control the reference value IPv6 OSPF uses Switch > enable Switch # configure terminal Switch (config) # router ipv6 ospf Switch (config-router)# auto-cost reference-bandwidth 1000 CLI Reference Guide 56 - D-Link DGS-6600-48TS | CLI Guide - Page 67
Sample Banner Login Message: DGS-6604 Chassis Ethernet Switch Command Line Interface, Command Mode Usage Guideline Firmware: Build 1.00.027 Copyright (c) 2011 D-Link Corporation, all rights reserved. line will be truncated and the first 80 characters are displayed. CLI Reference Guide 57 - D-Link DGS-6600-48TS | CLI Guide - Page 68
DGS-6604 Example This example shows how to modify the banner login message: banner login Switch:12(config)# banner login Command Line Interface, DGS-6604 Chassis Ethernet Switch Access for authorized users only. Please enter your username and password. Switch:12# CLI Reference Guide 58 - D-Link DGS-6600-48TS | CLI Guide - Page 69
DGS-6604 based-on client-id based-on optional field matches the configured Client Identifier. If the values match, the DHCP server provides service to the client. If the values do not match, the DHCP server does not respond config-dhcp)#based-on client-id hex 0x0152415320 CLI Reference Guide 59 - D-Link DGS-6600-48TS | CLI Guide - Page 70
DGS-6604 based-on c-vid based-on c-vid This command is used to specify the customer vlan ID (C-VID) as a rule for IP address assignment from Then the rule is added to and now based on C-VID 100/ 200 and S-VID 1000. switch(config-dhcp)#based-on s-vid 1000 CLI Reference Guide 60 - D-Link DGS-6600-48TS | CLI Guide - Page 71
DGS-6604 based-on interface-ip-address based-on interface-ip-address This command is used to specify a rule for a DHCP address pool to respond to a interface 172.19.10.100. switch(config)#ip dhcp pool pool1 switch(config-dhcp)#based-on interface-ip-address 172.19.10.100 CLI Reference Guide 61 - D-Link DGS-6600-48TS | CLI Guide - Page 72
DGS-6604 based-on mac-address based-on mac-address This command is used to specify the host MAC address as a rule for IP address assignment the DHCP address pool1. switch(config-dhcp)#based-on mac-address 00:80:C8:11:33:00,00:80:C8:11:33:FF CLI Reference Guide 62 - D-Link DGS-6600-48TS | CLI Guide - Page 73
DGS-6604 based-on relay-ip-address based-on relay-ip-address This command is used to specify a rule for the DHCP address pool's only response pool1) based on the Relay IP address. switch(config)#ip dhcp pool pool1 switch(config-dhcp)#based-on relay-ip-address 10.1.1.254 CLI Reference Guide 63 - D-Link DGS-6600-48TS | CLI Guide - Page 74
DGS-6604 based-on s-vid based-on s-vid This command is used to specify the service provider vlan ID (S-VID) as a rule for IP address assignment from the DHCP address pool. Use the no becomes based on S-VID 100/ 200 and C-VID 1000. switch(config-dhcp)#based-on c-vid 1000 CLI Reference Guide 64 - D-Link DGS-6600-48TS | CLI Guide - Page 75
DGS-6604 based-on user-class based-on user-class This command is used so that DHCP administrators can define specific user class identifiers to user class 0x8080 from DHCP address pool1. switch(config)#ip dhcp pool pool1 switch(config-dhcp)#based-on user-class hex 0x8080 CLI Reference Guide 65 - D-Link DGS-6600-48TS | CLI Guide - Page 76
DGS-6604 based-on vendor-class based-on vendor-class This command is used to create an address binding rule for the DHCP address pool based to match both Win98SE/ME and 2000/XP. switch(config)#ip dhcp pool pool1 switch(config-dhcp)#based-on vendor-class string MSFT CLI Reference Guide 66 - D-Link DGS-6600-48TS | CLI Guide - Page 77
DGS-6604 bgp always-compare-med bgp always-compare-med Use this command to compare the Multi-Exit Discriminator (MED) for paths from the autonomous system from which the paths are received: Switch(config)# router bgp 65534 Switch(config-router)# bgp always-compare-med CLI Reference Guide 67 - D-Link DGS-6600-48TS | CLI Guide - Page 78
DGS-6604 bgp asnotation dot bgp asnotation dot Use this command to change the default display and regular expression match format of BGP 4-byte . This example (on the next page) shows how to configure asnotation and shows the difference using the command show ip bgp: CLI Reference Guide 68 - D-Link DGS-6600-48TS | CLI Guide - Page 79
DGS-6604 bgp asnotation dot Switch # show ip bgp BGP table version is 30, local router ID is 10.10.11.50 Status codes: s suppressed, d .10.71.100 10.10.71.100 Metric LocPrf Weight Path 0 0 1.101 100 i 0 0 1.101 100 {80} i Total Entries: 2 entries, 2 routes Switch # CLI Reference Guide 69 - D-Link DGS-6600-48TS | CLI Guide - Page 80
DGS-6604 bgp bestpath as-path ignore bgp bestpath as-path ignore Use this command to ignore AS path as a factor in the selection of paths, prefer the path with the minimum cluster list length. 13. Always prefer the path that comes from the lowest neighbor address. CLI Reference Guide 70 - D-Link DGS-6600-48TS | CLI Guide - Page 81
DGS-6604 Example bgp bestpath as-path ignore Use the commands, bgp bestpath as-path ignore, bgp bestpath comparerouter-id or bgp default local- as the best path for autonomous system 65534: Switch(config)# router bgp 65534 Switch(config-router)# bgp bestpath as-path ignore CLI Reference Guide 71 - D-Link DGS-6600-48TS | CLI Guide - Page 82
DGS-6604 bgp and the route with the lowest router ID is selected. Unless manually defined, the router ID is the highest IP address on the router, with preference given to loopback addresses. Router ID can be manually set by using the bgp router-id command on page 78. This - D-Link DGS-6600-48TS | CLI Guide - Page 83
DGS-6604 bgp default ipv4-unicast bgp default ipv4-unicast Use this command to enable the IP version 4 (IPv4) unicast address family for all of a peer by default for autonomous system 65534: Switch(config)# router bgp 65534 Switch(config-router)# bgp default ipv4-unicast CLI Reference Guide 73 - D-Link DGS-6600-48TS | CLI Guide - Page 84
DGS-6604 bgp default local-preference bgp default local-preference Use this command to change the default local preference value. To return bgp 65534 Switch(config-router)# bgp default local-preference 200 Verify the settings by entering show ip protocols bgp command. CLI Reference Guide 74 - D-Link DGS-6600-48TS | CLI Guide - Page 85
DGS-6604 bgp deterministic-med bgp deterministic-med Use this command to include the Multi Exit Discriminator (MED) value for comparison of comparison of MED values for autonomous system 65534: Switch(config)# router bgp 65534 Switch(config-router)# bgp deterministic-med CLI Reference Guide 75 - D-Link DGS-6600-48TS | CLI Guide - Page 86
DGS-6604 bgp enforce-first-as bgp enforce-first-as Use this command to enforce the first AS for the eBGP routes. To disable this feature, AS path is the local AS number of the transmitting peer: Switch(config)# router bgp 65534 Switch(config-router)# bgp enforce-first-as CLI Reference Guide 76 - D-Link DGS-6600-48TS | CLI Guide - Page 87
DGS-6604 bgp log-neighbor-changes bgp log-neighbor- enables logging of both BGP resets and alternating status changes to use for troubleshooting purposes. Unexpected neighbor resets might indicate high error rates or high packet loss log for the BGP neighbor changes. CLI Reference Guide 77 - D-Link DGS-6600-48TS | CLI Guide - Page 88
DGS-6604 bgp router-id bgp router-id Use this command to configure a fixed router ID for the Border Gateway Protocol (BGP) routing process. Use how to change the router ID with 192.168.1.1 Switch(config)# router bgp 65100 Switch(config-router)# bgp router-id 192.168.1.1 CLI Reference Guide 78 - D-Link DGS-6600-48TS | CLI Guide - Page 89
DGS-6604 boot config boot config Use this when it is null (such as at a first-time start-up). If the software detects a problem with the boot config file, the device uses the factory default configuration for system boot up. • used as the factory default configuration. CLI Reference Guide 79 - D-Link DGS-6600-48TS | CLI Guide - Page 90
DGS-6604 boot config The specified URL must be represented by an absolute path. It cannot be represented by a relative path. configuration file. Switch# configure terminal Switch(config)# boot config flash:\yyy-config.exe Illegal configuration file Switch(config)# end T CLI Reference Guide 80 - D-Link DGS-6600-48TS | CLI Guide - Page 91
DGS-6604 bootfile boofile URL no bootfile bootfile This command is used to specify the name of the pool1. switch > enable switch# configure terminal switch(config)# ip dhcp pool pool1 switch(config-dhcp)# bootfile \dgs-6600\bootimage\mdubootfile.bin switch(config-dhcp)# CLI Reference Guide 81 - D-Link DGS-6600-48TS | CLI Guide - Page 92
DGS-6604 boot image boot image Use this command to specify the file used as the image file for the next boot. boot image [ check ] MEDIUM: image, flash:\switch-image0.bin becomes the secondary boot image file in the list and changes the status to the backup boot image. CLI Reference Guide 82 - D-Link DGS-6600-48TS | CLI Guide - Page 93
DGS-6604 Switch# configure terminal Switch(config)#boot image flash:\images\switch_image1.had Checking image at local flash:\images\switch_image1.had ... Update bootlist ....... Done. Done. Success Verify the settings by entering the show boot command. boot image CLI Reference Guide 83 - D-Link DGS-6600-48TS | CLI Guide - Page 94
DGS-6604 m channel-group chAC annel-group Use the channel-group command to assign an interface to a channel group. Use no channel- duplex setting in the same channel group. LACP protocol behavior will choose the members that are set to full duplex for the link aggregation. CLI Reference Guide 84 - D-Link DGS-6600-48TS | CLI Guide - Page 95
DGS-6604 m Example channel-group • In order to group. LACP protocol behavior will choose the members that have the same speed to for the link aggregation. This example shows how to configure a channel group. It assigns the eth3.4 to entering the show channel-group command CLI Reference Guide 85 - D-Link DGS-6600-48TS | CLI Guide - Page 96
DGS-6604 m class class Use this command to specify the name of the class map in order to define its traffic policy and enter into -action set-dscp-transmit 0 Switch(config-pmap-c)# exit Switch(config-pmap)# exit Verify the settings by entering the show policy-map command. CLI Reference Guide 86 - D-Link DGS-6600-48TS | CLI Guide - Page 97
DGS-6604 m class-map class-map To create a class map to be used for matching packets to a specified class, use the class-map command. To example (on the next page) specifies class_home_user as the name of a class map. In this class map, a match statement specifies that the CLI Reference Guide 87 - D-Link DGS-6600-48TS | CLI Guide - Page 98
DGS-6604 m class-map traffic that matches the access control list acl_home_user or match ipv6 protocol will be included in class_home_user. Switch( )# match protocol ipv6 Switch(config-cmap)# exit Switch(config)# Verify the settings by entering the show class-map command. CLI Reference Guide 88 - D-Link DGS-6600-48TS | CLI Guide - Page 99
DGS-6604 m clear aaa user lockout You can use this command to unlock the locked-out users. clear aaa user lockout {username USERNAME | all} The locked-out user jane is unlocked. Switch(config)# You can verify your settings by entering the show aaa user locked command CLI Reference Guide 89 - D-Link DGS-6600-48TS | CLI Guide - Page 100
DGS-6604 m clear arp-cache clear arp-cache To remove dynamically created entries from the Address Resolution Protocol (ARP) cache, use the clear with a specific IP interface. This example shows how to removes all dynamic entries from the ARP cache. Switch#clear arp-cache CLI Reference Guide 90 - D-Link DGS-6600-48TS | CLI Guide - Page 101
DGS-6604 m clear counters clear counters Use the command to clear counters for a specific port interface or all port interfaces. clear counters [ following example will clear eth 3.1-3.24 physical port s' statistic counters. Switch# clear counters eth3.1-3.24 Switch# CLI Reference Guide 91 - D-Link DGS-6600-48TS | CLI Guide - Page 102
DGS-6604 m clear dos prevention counter clear dos prevention counter Use this command to clear the counter of all attack types. clear Enabled Smurf Attack Enabled TCP Null Enabled TCP Xmas Enabled TCP SYNFIN Enabled TCP SYN SrcPort Less Than 1024 Enabled CLI Reference Guide 92 - D-Link DGS-6600-48TS | CLI Guide - Page 103
DGS-6604 m clear cpu-protect counters clear cpu-protect counters Use this command to clear the cpu-protect related counters. clear cpu-protect will be cleared. The following example shows how to clear all cpu-protect related statistics. Switch# clear cpu-protect counters CLI Reference Guide 93 - D-Link DGS-6600-48TS | CLI Guide - Page 104
DGS-6604 m clear gvrp statistics interface clear gvrp statistics interface Use the clear gvrp statistics command to clear the statistics of a single port cleared. This example shows how to clear the GVRP statistics on all interfaces. Switch# clear gvrp statistics Switch# CLI Reference Guide 94 - D-Link DGS-6600-48TS | CLI Guide - Page 105
DGS-6604 m clear ip bgp clear ip bgp To reset BGP connections using hard or soft reconfiguring, use the DMFBSJQCHQ command. clear ip access lists • Modifying the BGP-related weights • Modifying the BGP-related distribution lists • Modifying the BGP-related route maps CLI Reference Guide 95 - D-Link DGS-6600-48TS | CLI Guide - Page 106
DGS-6604 m Example clear ip bgp Use the in keyword to clear only the distribution lists • Modifying the BGP-related route maps If inbound routing tables are reset, all BGP routers must support route refresh capability (RFC 2918). In the following example, the BGP session is reset for BGP neighbor - D-Link DGS-6600-48TS | CLI Guide - Page 107
DGS-6604 m clear ip bgp peer-group clear ip bgp peer-group To reset BGP changes. It instead relies on dynamic exchange with supporting peers. Route refresh is advertised through BGP capability negotiation. All BGP routers must support the route refresh capability. CLI Reference Guide 97 - D-Link DGS-6600-48TS | CLI Guide - Page 108
DGS-6604 m Examples clear ip bgp peer-group To determine if a BGP router supports this capability, use the show ip bgp neighbors command on page 619 command. The following message is displayed in the output when the router supports ip bgp peer-group INTERNAL soft in Switch# CLI Reference Guide 98 - D-Link DGS-6600-48TS | CLI Guide - Page 109
DGS-6604 m clear ip dhcp binding clear ip dhcp binding Use this command to delete an address binding from the DHCP Server database. clear # clear ip dhcp binding 10.12.1.99 swtich# The following example deletes all bindings from all pools: switch# clear ip dhcp binding CLI Reference Guide 99 - D-Link DGS-6600-48TS | CLI Guide - Page 110
DGS-6604 m clear ip dhcp binding The following example deletes address binding 10.13.2.99 from the address pool named pool2: switch# clear ip dhcp pool pool2 binding 10.13.2.99 switch# Verify the settings by entering the show ip dhcp binding command. CLI Reference Guide 100 - D-Link DGS-6600-48TS | CLI Guide - Page 111
DGS-6604 m clear ip dhcp conflict clear ip dhcp conflict Use this command to clear an address conflict from the DHCP server database. # The following example deletes all the address conflicts from the entire DHCP server database. switch#clear ip dhcp conflict switch# CLI Reference Guide 101 - D-Link DGS-6600-48TS | CLI Guide - Page 112
DGS-6604 m clear ip dhcp conflict The following example deletes all the address conflicts from the address pool named pool1: switch#clear ip dhcp conflict pool pool1 switch# CLI Reference Guide 102 - D-Link DGS-6600-48TS | CLI Guide - Page 113
DGS-6604 m clear ip dhcp server statistics clear ip dhcp server statistics Use this command to reset all Dynamic Host Configuration Protocol (DHCP to zero. Example The following example resets all DHCP counters to zero. switch# clear ip dhcp server statistics switch# CLI Reference Guide 103 - D-Link DGS-6600-48TS | CLI Guide - Page 114
DGS-6604 m clear ip ospf Use this command to restart the OSPF process. clear ip ospf clear ip ospf Syntax None Default None Command Mode having to reboot the switch. Example This example shows how to restart all of OSPF processes Switch>enable Switch# clear ip ospf CLI Reference Guide 104 - D-Link DGS-6600-48TS | CLI Guide - Page 115
DGS-6604 m clear ipv6 dhcp client clear ipv6 dhcp client This command is used to restart the DHCPv6 client on an interface. ). The following example restarts the DHCPv6 client for interface vlan1: Switch > enable Switch # clear ipv6 dhcp client vlan1 Success. Switch # CLI Reference Guide 105 - D-Link DGS-6600-48TS | CLI Guide - Page 116
DGS-6604 m clear ipv6 neighbors This command is used to clear the IPv6 neighbor information. clear ipv6 neighbors clear ipv6 neighbors [ Example This example shows how to clear instances of IPv6 neighbors: Switch > enable Switch # clear ipv6 neighbors vlan1 Switch # CLI Reference Guide 106 - D-Link DGS-6600-48TS | CLI Guide - Page 117
DGS-6604 m clear ipv6 ospf process clear ipv6 ospf process To restart the state of IPv6 OSPF, use the clear ipv6 ospf process command example restarts the SPF algorithm by clearing the IPv6 OSPF processes from the database. Switch > enable Switch # clear ipv6 ospf process CLI Reference Guide 107 - D-Link DGS-6600-48TS | CLI Guide - Page 118
DGS-6604 m clear ipv6 rip clear ipv6 rip To delete routes from the IPv6 RIP routing table, use the clear ipv6 rip command. clear are deleted. Examples The following example deletes all the IPv6 routes for the RIP process. Switch > enable Switch # clear ipv6 rip CLI Reference Guide 108 - D-Link DGS-6600-48TS | CLI Guide - Page 119
DGS-6604 m clear lldp neighbors clear lldp neighbors Use this command to delete all LLDP information learned from neighboring devices. clear lldp neighbors [ . This example shows how to delete all neighboring information on all interfaces: Switch# clear lldp neighbors CLI Reference Guide 109 - D-Link DGS-6600-48TS | CLI Guide - Page 120
DGS-6604 m clear lldp statistics Use this command to delete LLDP statistics. clear lldp statistics [interface INTERFACE-ID [, | -] ] clear lldp statistics LLDP statistics will be cleared. This example shows how to reset all LLDP statistics: Switch# clear lldp statistics . CLI Reference Guide 110 - D-Link DGS-6600-48TS | CLI Guide - Page 121
DGS-6604 m clear logging clear logging Use this command to clear log messages from the system logging buffer. clear logging Syntax None buffer. Example The following example to show how to clear log messages in buffer. Switch> enable Switch# clear logging Switch# CLI Reference Guide 111 - D-Link DGS-6600-48TS | CLI Guide - Page 122
DGS-6604 m clear mac address-table clear mac address-table Use the clear mac address-table command to delete from the MAC address table: • specific -table dynamic address 00:08:00:70:00:07 Verify the information was deleted by entering the show mac address-table command. CLI Reference Guide 112 - D-Link DGS-6600-48TS | CLI Guide - Page 123
DGS-6604 m clear port-security clear port-security To delete all of the secured MAC addresses, except for manually configured secured MAC addresses, from the MAC address table, use the clear portsecurity specific interface: Switch# clear port-security interface eth3.1 CLI Reference Guide 113 - D-Link DGS-6600-48TS | CLI Guide - Page 124
DGS-6604 m clear running-config factory-defaults clear running-config factory-defaults Use this command to clear the system's running The following example demonstrates how to clear system running configuration. Switch# clear running-config factory-defaults Switch# CLI Reference Guide 114 - D-Link DGS-6600-48TS | CLI Guide - Page 125
DGS-6604 m clear spanning-tree detected-protocols clear 802.1D stays in 802.1D mode even after the legacy bridge has been removed from the link. Similarly, an MST port assumes that it is a boundary port when the bridges which it clear spanning-tree detected-protocols CLI Reference Guide 115 - D-Link DGS-6600-48TS | CLI Guide - Page 126
DGS-6604 m clear vlan-tunnel ctag-mapping dynamic clear vlan-tunnel ctag-mapping dynamic Use this command to clear all dynamically learned shows how to clear all dynamically learned customer VLAN tag mappings. Switch# clear vlan-tunnel ctag-mapping dynamic Switch# CLI Reference Guide 116 - D-Link DGS-6600-48TS | CLI Guide - Page 127
DGS-6604 m clock set Use this command to manually not necessary to set the clock manually. Use this command if no file. If the clock is manually set and the SNTP server server set time replaces the manually set time. If the SNTP The following example shows how to manually set the software clock to 6:00 - D-Link DGS-6600-48TS | CLI Guide - Page 128
DGS-6604 m clock summer-time clock summer-time Use one of the optional keyword formats of the clock summer-time command to configure the parameter to express the beginning of the time adjustment period while the ending of the period is expressed in the second portion. CLI Reference Guide 118 - D-Link DGS-6600-48TS | CLI Guide - Page 129
DGS-6604 m Example clock summer-time The following example shows how to specify that summer time starts on the first Sunday in April at 2 a.m. -time recurring 1 sun April 2:00 last sun October 2:00 Switch(config)# end Verify the settings by entering the show clock command. CLI Reference Guide 119 - D-Link DGS-6600-48TS | CLI Guide - Page 130
DGS-6604 m clock timezone clock timezone Use the command to set the time zone for display purpose. To set the time to UTC: Switch# configure terminal Switch(config)# clock timezone - 8 Switch(config)# end Verify the settings by entering the show clock command. CLI Reference Guide 120 - D-Link DGS-6600-48TS | CLI Guide - Page 131
DGS-6604 m color-aware color-aware color-aware Use the color-aware command the port to trust CoS and defines the CoS to color map. Switch(config)# interface eth3.1 Swtich (config-if)# service-policy pcolor-map1 Swtich (config-if)# qos trust cos Swtich (config-if)# qos map cos-color 1-7 to green - D-Link DGS-6600-48TS | CLI Guide - Page 132
DGS-6604 m command prompt command prompt Use this command to change the device CLI after the command is executed. This example shows how to change the prompt to use the system name. DGS-6600:15# command prompt system-name switch:15# The following example shows how to set the command prompt back - D-Link DGS-6600-48TS | CLI Guide - Page 133
DGS-6604 m command prompt The following example shows how to hide the privilege information from the console prompt. DGS-6600:15# command prompt no-level DGS-6600# This example shows define alpha as the console prompt. DGS-6600:15# command prompt level string alpha alpha:15# CLI Reference Guide - D-Link DGS-6600-48TS | CLI Guide - Page 134
DGS-6604 m configure terminal Use this command to enter the global configuration mode configure terminal configure terminal Syntax None configuration. Example This example shows how to enter into the configuration mode: Switch#configure terminal Switch(config)# CLI Reference Guide 124 - D-Link DGS-6600-48TS | CLI Guide - Page 135
DGS-6604 m copy copy Use the copy command to copy a image, log or configuration file from a remote or local source to a local or remote current configuration file in NVRAM and the file name will be maintained as the file name specified with boot config command. CLI Reference Guide 125 - D-Link DGS-6600-48TS | CLI Guide - Page 136
DGS-6604 m copy IP-ADDRESS\ DIRECTORY\ The IP address of TFTP server. The directory name of the source or destination file in TFTP server. it is a configuration file or not (the boot config command will also check whether it is a configuration file or not first). CLI Reference Guide 126 - D-Link DGS-6600-48TS | CLI Guide - Page 137
DGS-6604 m Examples copy This example shows how to configure the switch (running configuration) to use a configuration (switch-config.txt : Switch# copy running-config startup-config Save system configuration (y/n) [n], y Configuration has been copied successfully. Switch# CLI Reference Guide 127 - D-Link DGS-6600-48TS | CLI Guide - Page 138
DGS-6604 m cos remarking cos remarking Use this command to remark the receiving CoS priority for a VLAN tunnel application. Use the no form of is only applied to outer priority tag in VLAN encapsulation and the COS remarking (replacement) is applied for the VLAN remarking. CLI Reference Guide 128 - D-Link DGS-6600-48TS | CLI Guide - Page 139
DGS-6604 m cos remarking Use the no cos remarking C-VID command (with optional parameters) to set the related C-VID as customer CoS trusted at as Customer CoS trusted now. Switch(config-if)#>no cos remarking 101 Verify the settings by entering show vlan-tunnel command. CLI Reference Guide 129 - D-Link DGS-6600-48TS | CLI Guide - Page 140
DGS-6604 m cpu-protect safeguard cpu-protect safeguard Use this command to enable and configure the threshold for Safeguard Engine. Use the Engine. The rising and falling threshold are 60 and 40 respectively. Switch(config)# cpu-protect safeguard threshold 60 40 CLI Reference Guide 130 - D-Link DGS-6600-48TS | CLI Guide - Page 141
DGS-6604 m cpu-protect safeguard The following example shows how to disable Safeguard Engine and reset threshold to default value. Switch(config)# no cpu-protect safeguard You can verify your settings by entering show cpu-protect safeguard command. CLI Reference Guide 131 - D-Link DGS-6600-48TS | CLI Guide - Page 142
DGS-6604 m cpu-protect type cpu-protect example, bgp) to be configured. See the "Usage Guideline" for a list of protocols supported by most routers. RATE Specify the threshold. The unit is packets per second. The valid at the column of "Classification (subinterface)". CLI Reference Guide 132 - D-Link DGS-6600-48TS | CLI Guide - Page 143
DGS-6604 m cpu-protect type Table 1 Supported protocol name for the command except NDP NS/NA/RS/RA/Redirect (IPv6) Internet Group Management Protocol(IPv4) Link Aggregation Control Protocol Open Shortest Path First (IPv4) Open Shortest Path First (IPv6 type ospf pps 100 CLI Reference Guide 133 - D-Link DGS-6600-48TS | CLI Guide - Page 144
DGS-6604 m cpu-protect type The following example shows how to remove threshold of OSPF protocol packet. Switch(config)# no cpu-protect type ospf Verifying the settings by show cpu-protect type command. CLI Reference Guide 134 - D-Link DGS-6600-48TS | CLI Guide - Page 145
DGS-6604 m cpu-protect sub-interface cpu-protect sub-interface Use this command to configure the rate-limit for traffic destined to CPU traffic. Switch(config)# no cpu-protect sub-interface manage Switch# Verifying the settings by show cpu-protect sub-interface command. CLI Reference Guide 135 - D-Link DGS-6600-48TS | CLI Guide - Page 146
DGS-6604 m crypto key crypto key To generate and for overwriting existing keys. Default Command Mode Usage Guideline Example None Privileged EXEC To support SSH login, an RSA or DSA key pair must first be generated. This command Generating RSA keys.... [OK] Switch# CLI Reference Guide 136 - D-Link DGS-6600-48TS | CLI Guide - Page 147
DGS-6604 mm ddm log ddm log no ddm log Syntax Description Default Command Mode Usage Guideline Example ddm log This command configures the an abnormal status. The following example shows how to disable logging for ddm. switch# configure terminal switch(config)# no ddm log CLI Reference Guide 137 - D-Link DGS-6600-48TS | CLI Guide - Page 148
DGS-6604 mm ddm state This command configures the ddm SFP's abnormal status or a port that recovers from an abnormal status. For SFP not support DDM function, the system will never detect its status even if the configuration on the port DDM (config-if)# ddm state disable CLI Reference Guide 138 - D-Link DGS-6600-48TS | CLI Guide - Page 149
DGS-6604 mm ddm shutdown ddm shutdown This command configures . Interface configuration. This command can be used to control if shutdown on a linked port occurs when the system detects the SFP's abnormal status and which level of eth3.1 Switch(config)# ddm shutdown alarm CLI Reference Guide 139 - D-Link DGS-6600-48TS | CLI Guide - Page 150
DGS-6604 mm ddm temperature ddm temperature This SFP+ ny I2C. Interface configuration. Only SFP/SFP+ port interfaces with: optical module support DDM; are valid for this configuration. This command configures the temperature thresholds on the value 127.992 is chosen. CLI Reference Guide 140 - D-Link DGS-6600-48TS | CLI Guide - Page 151
DGS-6604 mm ddm voltage ddm voltage This SFP+ ny I2C. Interface configuration. Only SFP/SFP+ port interfaces with: optical module support DDM; are valid for this configuration. This command configures the voltage thresholds on the specified closest value 0.005 is chosen. CLI Reference Guide 141 - D-Link DGS-6600-48TS | CLI Guide - Page 152
DGS-6604 mm ddm bias-current ddm SFP/SFP+ ny I2C. Interface configuration. Only SFP/SFP+ port interfaces with: optical module support DDM; are valid for this configuration. This command configures the bias-current thresholds on the specified closest value 10.238 is chosen. CLI Reference Guide 142 - D-Link DGS-6600-48TS | CLI Guide - Page 153
DGS-6604 mm ddm tx-power SFP/SFP+ ny I2C. Interface configuration. Only SFP/SFP+ port interfaces with: optical module support DDM; are valid for this configuration. This command configures the tx-power thresholds on the specified definition, closest value 0.1810 is chosen. CLI Reference Guide 143 - D-Link DGS-6600-48TS | CLI Guide - Page 154
DGS-6604 mm ddm rx-power ddm SFP/SFP+ ny I2C. Interface configuration. Only SFP/SFP+ port interfaces with: optical module support DDM; are valid for this configuration. This command configures the rx-power thresholds on the definition, closest value 0.1810 is chosen. CLI Reference Guide 144 - D-Link DGS-6600-48TS | CLI Guide - Page 155
DGS-6604 mm default-gateway (management port) default-gateway (management port) Use this command to set the IP address of the default gateway. Use if switch(mgmt-if)#default-gateway 10.1.1.254 switch(mgmt-if)#end Verify the settings by entering the show mgmt-if command CLI Reference Guide 145 - D-Link DGS-6600-48TS | CLI Guide - Page 156
DGS-6604 mm default-information originate (BGP) default-information originate (BGP) Use this command to configure a Border Gateway Protocol (BGP) Switch(config-router)# default-information originate Verify the settings by entering the show ip protocols BGP command. CLI Reference Guide 146 - D-Link DGS-6600-48TS | CLI Guide - Page 157
DGS-6604 mm default-information originate is from 0-16777214. metric-type TYPE-VALUE (Optional) IPv6 OSPF specifies the external link type associated with the default route advertised into the IPv6 OSPF routing domain. It can router)# default-information originate always CLI Reference Guide 147 - D-Link DGS-6600-48TS | CLI Guide - Page 158
DGS-6604 mm default-information originate (RIP) default-information originate (RIP) To generate a default route into Routing Information Protocol ( rip Switch(config-router)# default-information originate Verify the settings by entering the show running-config command. CLI Reference Guide 148 - D-Link DGS-6600-48TS | CLI Guide - Page 159
DGS-6604 mm default-information originate (RIP IPv6) default-information originate (RIP IPv6) To originate a default IPv6 route into RIP . Switch > enable Switch # configure terminal Switch (config) # router ipv6 rip Switch (config-router) # default-information originate CLI Reference Guide 149 - D-Link DGS-6600-48TS | CLI Guide - Page 160
DGS-6604 mm default ipv6 nd prefix default ipv6 nd prefix This command is used to default the IPv6 RA prefix information. default # configure terminal Switch (config) # interface vlan1 Switch (config-if) # default ipv6 nd prefix 3ffe:501:ffff::/64 Switch (config-if) # CLI Reference Guide 150 - D-Link DGS-6600-48TS | CLI Guide - Page 161
DGS-6604 mm default-metric (OSPF) default-metric the same metric value for all redistributed routes. A default metric helps solve the problem of redistributing routes with an incompatible metric. Whenever a metric does not convert, rip Switch(config-router)# end Switch# CLI Reference Guide 151 - D-Link DGS-6600-48TS | CLI Guide - Page 162
DGS-6604 mm default-metric (IPv6 OSPF) metric value for all redistributed routes. A default metric helps solve the problem of redistributing routes with an incompatible metric. Whenever a metric does not convert default-metric 10 Switch (config-router) # redistribute rip CLI Reference Guide 152 - D-Link DGS-6600-48TS | CLI Guide - Page 163
DGS-6604 mm default-metric (RIP) default-metric (RIP the same metric value for all redistributed routes. A default metric helps solve the problem of redistributing routes with an incompatible metric. Whenever a metric does not convert, the show ip protocols rip command. CLI Reference Guide 153 - D-Link DGS-6600-48TS | CLI Guide - Page 164
DGS-6604 mm default-metric (RIP IPv6) metric value for all redistributed routes. A default metric helps solve the problem of redistributing routes with an incompatible metric. Whenever a metric cannot convert, # default-metric 10 Switch (config-router) # redistribute ospf CLI Reference Guide 154 - D-Link DGS-6600-48TS | CLI Guide - Page 165
DGS-6604 mm default-router default-router This command specifies the default router list for a DHCP client. Use the no form of this -router in DHCP address pool. switch# configure terminal switch(config)# ip dhcp pool pool1 switch(config-dhcp)# default-router 10.1.1.1 CLI Reference Guide 155 - D-Link DGS-6600-48TS | CLI Guide - Page 166
DGS-6604 mm delete Use this command to delete a file. delete FILE-SYSTEM:\ [PATH-NAME\] FILE-NAME delete Syntax Description FILE-SYSTEM Specifies it cannot be deleted and an error message will be displayed. Switch#delete cf1:\test.txt Delete cf1:\test.txt, (y/n) [n]? CLI Reference Guide 156 - D-Link DGS-6600-48TS | CLI Guide - Page 167
DGS-6604 mm description description Use this command to add a description for an interface. Use the no description to clear the interface )# interface eth3.10 Switch(config-if)# description Physical Port 10 Verify the settings by entering the show interface command.G CLI Reference Guide 157 - D-Link DGS-6600-48TS | CLI Guide - Page 168
DGS-6604 mm dir dir Use the dir command to display the information for a file or the file system on the system's cf1 flash. Switch>dir cf1:\ log customer system runtime.1.00.017_DGS-6600.had runtime.1.00.018_DGS-6600.had Switch> 64212362 bytes 73087296 bytes CLI Reference - D-Link DGS-6600-48TS | CLI Guide - Page 169
DGS-6604 mm disable disable Syntax Default Command Mode Usage Guideline Example disable Use this command to return to the User EXEC mode from example shows how to logout after executing the disable command to return to the User EXEC mode. Switch# disable Switch> logout CLI Reference Guide 159 - D-Link DGS-6600-48TS | CLI Guide - Page 170
DGS-6604 mm distance distance Use the command distance to define the destination PREFIX-LENGTH network. The Network-Prefix/Prefix-Length parameter is not supported for OSPF. Default No static routes are established. The table below shows will be applied to this route. CLI Reference Guide 160 - D-Link DGS-6600-48TS | CLI Guide - Page 171
DGS-6604 mm Examples distance If the distances be active at the same time. Note 1: BGP Protocol does not support this command. Note 2: OSPF does not support the parameter: [NETWORK-PREFIX/PREFIXLENGTH]. This example shows how to set entering the show ip protocols command. CLI Reference Guide 161 - D-Link DGS-6600-48TS | CLI Guide - Page 172
DGS-6604 mm dns-server dns-server This command configures the IP address list of DNS servers available to DHCP clients. Use the no of DNS server in DHCP address pool. switch# configure terminal switch(config)# ip dhcp pool pool1 switch(config-dhcp)# dns-server 10.1.1.1 CLI Reference Guide 162 - D-Link DGS-6600-48TS | CLI Guide - Page 173
DGS-6604 mm domain-name domain-name This command configures the domain name for a DHCP client. Use the no form of this command to "dlink.com" in a DHCP address pool. switch# configure terminal switch(config)# ip dhcp pool pool1 switch(config-dhcp)# domain-name dlink.com CLI Reference Guide 163 - D-Link DGS-6600-48TS | CLI Guide - Page 174
DGS-6604 mm dos_prevention action dos_prevention action Use this command to specify the action to perform when a DoS attack occurs dos_prevention action trap_log The following example shows how to remove action trap_log. Switch# no dos_prevention action trap_log CLI Reference Guide 164 - D-Link DGS-6600-48TS | CLI Guide - Page 175
DGS-6604 mm dos_prevention type dos_prevention type Use this command to enable/disable DoS prevention mechanism. The packet matching specific packets. tcp_synfin Port scanning by using specific packets. tcp_syn_srcport_less_1024 Port scanning by using specific packets. CLI Reference Guide 165 - D-Link DGS-6600-48TS | CLI Guide - Page 176
DGS-6604 mm dos_prevention type Syntax Description - continued all All of the above types. Default Command Mode Usage Guideline Examples Disabled. DoS prevention of all supported attack types or for all supported types. The following example mechanism for all supported types. Switch# configure - D-Link DGS-6600-48TS | CLI Guide - Page 177
DGS-6604 mm dot1v binding protocol-group dot1v binding protocol-group Use the dot1v binding protocol-group interface configuration command to set (config-if)# dot1v binding protocol-group 10 vlan 3000 Verify the settings by entering the show dot1v interface command. CLI Reference Guide 167 - D-Link DGS-6600-48TS | CLI Guide - Page 178
DGS-6604 mm dot1v protocol-group dot1v protocol-group Use the dot1v protocol-group global configuration command to add a protocol to a protocol (config)# dot1v protocol-group 10 frame ethernet2 0x86dd Verify the settings by entering the show dot1v protocol-group command. CLI Reference Guide 168 - D-Link DGS-6600-48TS | CLI Guide - Page 179
DGS-6604 mm dot1x auth-mode dot1x auth-mode Use the dot1x auth-mode command to specify the 802.1x authentication mode. dot1x auth- )#interface eth4.3 Switch(config-if)# dot1x auth-mode host-based Verify the settings by entering the show dot1x auth-configuration command. CLI Reference Guide 169 - D-Link DGS-6600-48TS | CLI Guide - Page 180
DGS-6604 mm dot1x auth-protocol dot1x auth-protocol Use this command to specify the authentication method used for 802.1x authentication. dot1x terminal Switch(config)# dot1x auth-protocol radius Verify the settings by entering the show dot1x command on page 596. CLI Reference Guide 170 - D-Link DGS-6600-48TS | CLI Guide - Page 181
DGS-6604 mm dot1x control-direction dot1x control-direction Use this command to configure the direction of the traffic on a controlled port as eth4.1 Switch(config-if)# dot1x control-direction in Verify the settings by entering the show dot1x auth-configuration command. CLI Reference Guide 171 - D-Link DGS-6600-48TS | CLI Guide - Page 182
DGS-6604 mm dot1x default dot1x default Using this command resets the configurable 802.1X parameters to the default values. dot1x (config)# interface eth4.1 Switch(config-if)# dot1x default Verify the settings by entering the show dot1x auth-configuration command. CLI Reference Guide 172 - D-Link DGS-6600-48TS | CLI Guide - Page 183
DGS-6604 mm dot1x forward-pdu dot1x forward-pdu Use this command to allow a 1X-disabled interface to forward 802.1X BPDU. Use Switch(config)# interface eth4.1 Switch(config-if)# dot1x forward-pdu Verify the settings by entering the show dot1x auth-configuration command. CLI Reference Guide 173 - D-Link DGS-6600-48TS | CLI Guide - Page 184
DGS-6604 mm dot1x guest-vlan dot1x guest- a port is configured as 1X-enabled and dot1x port-control is in auto mode. This command only supports ports in access VLAN mode. When configuring a guest VLAN for a port in other VLAN modes, an join the IEEE 802.1x guest VLAN. CLI Reference Guide 174 - D-Link DGS-6600-48TS | CLI Guide - Page 185
DGS-6604 mm dot1x guest-vlan Switch# configure terminal Switch(config)# interface eth4.1 Switch(config-if)# dot1x guest-vlan 99 This example (config-if)# no dot1x guest-vlan Verify the settings by entering show do1x auth-configuration and show vlan interface command. CLI Reference Guide 175 - D-Link DGS-6600-48TS | CLI Guide - Page 186
DGS-6604 mm dot1x initialize Use this command to initialize the authentication state machine of: • a port in port-based mode. -or• an associated MAC address in MAC address 00-40-10-28-19-78 on eth4.1. Switch# dot1x initialize interface eth4.1 mac-address 00-40-10-28-19-78 CLI Reference Guide 176 - D-Link DGS-6600-48TS | CLI Guide - Page 187
DGS-6604 mm dot1x max-req dot1x max-req Use this command to set the maximum number of times that the switch sends configure terminal Switch(config)# interface eth4.1 Switch(config-if)# dot1x max-req 3 Verify the settings with the show dot1x auth-configuration command. CLI Reference Guide 177 - D-Link DGS-6600-48TS | CLI Guide - Page 188
DGS-6604 mm dot1x pae authenticator dot1x pae authenticator Use this command to enable 802.1X authentication on a specific port. Use the 802.1x authentication on port eth4.1. Switch# configure terminal Switch(config)# interface eth4.1 Switch(config-if)# no dot1x pae CLI Reference Guide 178 - D-Link DGS-6600-48TS | CLI Guide - Page 189
DGS-6604 mm dot1x port-control dot1x port-control Use this command to manually control the authorization state on a specific port. dot1x port-control {auto | force-authorized | force- -unauthorized Verify the settings with the show dot1x auth-configuration command. CLI Reference Guide 179 - D-Link DGS-6600-48TS | CLI Guide - Page 190
DGS-6604 mm dot1x re-authenticate dot1x re-authenticate Use this command to re-authenticate a specific port or a specific MAC address. dot1x re-authenticate [ 00-40-10-28-19-78 on eth4.1. Switch# dot1x re-authenticate interface eth4.1 mac-address 00-40-10-28-19-78 CLI Reference Guide 180 - D-Link DGS-6600-48TS | CLI Guide - Page 191
DGS-6604 mm dot1x re-authentication dot1x re-authentication Use this command to enable periodic re-authentication. Use the no form of interface eth4.1 Switch(config-if)# no dot1x re-authentication Verify the settings by entering the show dot1x auth-configuration command. CLI Reference Guide 181 - D-Link DGS-6600-48TS | CLI Guide - Page 192
DGS-6604 mm dot1x system-auth-control dot1x system-auth-control Use dot1x system-auth-control to globally enable 802.1X authentication terminal Switch(config)# no dot1x system-auth-control Verify the settings by entering the show dot1x auth-configuration command. CLI Reference Guide 182 - D-Link DGS-6600-48TS | CLI Guide - Page 193
DGS-6604 mm dot1x timeout dot1x timeout Use this command to set time-out values for various 802.1X timers. dot1x timeout {quiet-period timeout 15 Switch(config-if)# dot1x timeout tx-period 10 Verify the settings by entering the show dot1x auth-configuration command. CLI Reference Guide 183 - D-Link DGS-6600-48TS | CLI Guide - Page 194
DGS-6604 mm dot1x user dot1x user Use this command to create a local account used for authentication. Use the no form of this as "yourname". Switch# configure terminal Switch(config)# no dot1x user yourname Verify the settings by entering the show dot1x user command. CLI Reference Guide 184 - D-Link DGS-6600-48TS | CLI Guide - Page 195
DGS-6604 mm duplex duplex Use this command to configure Only physical port interfaces are valid for this configuration. If the duplex mode is not supported by the hardware, an error message will be returned. 100 FX is always fixed to entering the show interface command. CLI Reference Guide 185 - D-Link DGS-6600-48TS | CLI Guide - Page 196
DGS-6604 m enAE able Use this command to enter a Privileged EXEC mode. enable [privilege LEVEL] enable Syntax Description privilege LEVEL (Optional) . This example shows how to enter the Privileged EXEC mode: Switch> enable Input privileged level 15 password: Switch# CLI Reference Guide 186 - D-Link DGS-6600-48TS | CLI Guide - Page 197
DGS-6604 m enable password enable password Use this command to setup the enable password to enter into different privileged modes. with "MyEnablePassword". Switch(config)# enable password MyEnablePassword Verify the settings by entering the show enable password command. CLI Reference Guide 187 - D-Link DGS-6600-48TS | CLI Guide - Page 198
DGS-6604 m end end end Use this command to end the current configuration session and go back to the Privileged EXEC mode. Syntax Default the session. This example shows how to end the interface configuration and go back to privileged mode. Switch(config-if)#end Switch# CLI Reference Guide 188 - D-Link DGS-6600-48TS | CLI Guide - Page 199
DGS-6604 m exit exit Syntax Default Command Mode Usage Guideline Example exit Use this command to end the current configuration mode and go to exit from the interface configuration mode and return to the global configuration mode. Switch(config-if)#exit Switch(config)# CLI Reference Guide 189 - D-Link DGS-6600-48TS | CLI Guide - Page 200
DGS-6604 m erps erps no erps Syntax Default Command Mode Usage Guideline erps Use the erps command to enable ERPS function globally. (config)# erps Switch(config)# The following example shows how to disable ERPS function globally: Switch(config)# no erps Switch(config)# CLI Reference Guide 190 - D-Link DGS-6600-48TS | CLI Guide - Page 201
DGS-6604 m erps domain erps domain Use the erps domain command to create or modify an ERPS domain and enter the ERPS domain configuration -erps-domain)# The following example shows how to delete ERPS domain campus: Switch(config)# no erps domain campus Switch(config)# CLI Reference Guide 191 - D-Link DGS-6600-48TS | CLI Guide - Page 202
DGS-6604 m erpi enable erpi enable APS controlled VLAN. In addition to R-APS controlled VLAN and ring ports, the configuration of service protected VLANs and RPL related settings are fundamental for the setup of an ERP instance. The 1 enable Switch(config-erps-domain)# CLI Reference Guide 192 - D-Link DGS-6600-48TS | CLI Guide - Page 203
DGS-6604 m erpi type erpi type Use the erpi type command to create an ERP instance with ring type in an ERPS domain. Use the as a sub ring: Switch(config-erps-domain)# erpi 2 type sub Switch(config-erps-domain)# The following example shows how to delete ERP instance 1: CLI Reference Guide 193 - D-Link DGS-6600-48TS | CLI Guide - Page 204
DGS-6604 m Switch(config-erps-domain)# no erpi 1 Switch(config-erps-domain)# erpi type CLI Reference Guide 194 - D-Link DGS-6600-48TS | CLI Guide - Page 205
DGS-6604 m erpi raps-vlan erpi raps-vlan Use the erpi raps-vlan command to configure the R-APS controlled VLAN of an ERP instance. how to remove R-APS controlled VLAN setting of ERP instance 1: Switch(config-erps-domain)# no erpi 1 raps-vlan Switch(config-erps-domain)# CLI Reference Guide 195 - D-Link DGS-6600-48TS | CLI Guide - Page 206
DGS-6604 m erpi ring-mel erpi ring-mel Use the erpi ring-mel command to configure ring MEL value of an ERP instance. Use the no to return ring MEL value to default value of ERP instance 1: Switch(config-erps-domain)# no erpi 1 ring-mel Switch(config-erps-domain)# CLI Reference Guide 196 - D-Link DGS-6600-48TS | CLI Guide - Page 207
DGS-6604 m erpi ring-port erpi ring-port Use the erpi ring-port command to configure the ring ports of an ERP instance. Use the channel1" as the east ring port of ERP instance 1: Switch(config-erps-domain)# erpi 1 ring-port east port-channel1 Switch(config-erps-domain)# CLI Reference Guide 197 - D-Link DGS-6600-48TS | CLI Guide - Page 208
DGS-6604 m erpi ring-port The following example shows how to remove east ring port setting of ERP instance 1: Switch(config-erps-domain)# no ring port of ERP instance 2 (sub ERP instance) Switch(config-erps-domain)# no erpi 2 ring-port shared Switch(config-erps-domain)# CLI Reference Guide 198 - D-Link DGS-6600-48TS | CLI Guide - Page 209
DGS-6604 m erpi rpl erpi rpl Use the erpi rpl command to configure an ERP instance as the RPL owner and the RPL port. Use the )# The following example shows how to disable RPL owner of ERP instance 1: Switch(config-erps-domain)# no erpi 1 rpl Switch(config-erps-domain)# CLI Reference Guide 199 - D-Link DGS-6600-48TS | CLI Guide - Page 210
DGS-6604 m erpi protected-vlan erpi protected-vlan Use the erpi protected-vlan command to add or remove service protected VLANs for an ERP instance. Use the no form of this command to remove all service the service protected service protected service add service protected VLANs add service - D-Link DGS-6600-48TS | CLI Guide - Page 211
protected-vlan Switch(config-erps-domain)# erpi 1 protected-vlan remove 3 Switch(config-erps-domain)# The following example shows how to remove all service protected VLANs of ERP instance 1: Switch(config-erps-domain)# no erpi 1 protected-vlan Switch(config-erps-domain)# CLI Reference Guide 201 - D-Link DGS-6600-48TS | CLI Guide - Page 212
DGS-6604 m erpi timer erpi timer Use the erpi timer command to configure timers for an ERP instance. Use the no form of this command shows how to configure WTR timer to 1 minutes of ERP instance 1: Switch(config-erps-domain)# erpi 1 timer wtr 1 Switch(config-erps-domain)# CLI Reference Guide 202 - D-Link DGS-6600-48TS | CLI Guide - Page 213
DGS-6604 m erpi timer The following example shows how to configure hold-off timer as default time value of ERP instance 1: Switch(config-erps-domain)# no erpi 1 timer hold-off Switch(config-erps-domain)# CLI Reference Guide 203 - D-Link DGS-6600-48TS | CLI Guide - Page 214
DGS-6604 m erpi tc-propagation erpi tc-propagation Use the erpi tc-propagation command to enable topology change propagation of the sub ERP 2 in ERPS domain 1: Switch(config)# erps domain 1 Switch(config-erps-domain)# no erpi 2 tc-propagation Switch(config-erps-domain)# CLI Reference Guide 204 - D-Link DGS-6600-48TS | CLI Guide - Page 215
DGS put in error disabled state (an operational state that is similar to the link-down state) by causes such as loopback detection. A port in error enter shutdown and then no shutdown commands to recover an interface manually from the error-disabled state. If auto recovery is enabled for Guide 205 - D-Link DGS-6600-48TS | CLI Guide - Page 216
DGS-6604 m errdisable recovery The following example shows how to enable the auto recovery for loopbackdetection. Switch# configure terminal Switch( cause loopback-detection Switch(config)# end You can verify your settings by entering the show errdisable recovery command. CLI Reference Guide 206 - D-Link DGS-6600-48TS | CLI Guide - Page 217
DGS-6604 m flowcontrol floA wcontrol Use this command to configure is because flow control capability is determined by both the local port, device and its linked partner instead of just the local setting. If auto-negotiation is disabled (i.e. the for this configuration. CLI Reference Guide 207 - D-Link DGS-6600-48TS | CLI Guide - Page 218
DGS-6604 m Example flowcontrol This example shows how to turn on the flow control send capability of interface eth3.1. Switch# configure terminal .1 Switch(config-if)# flowcontrol send on Switch(config-if)# end Verify the settings by entering the show interface command. CLI Reference Guide 208 - D-Link DGS-6600-48TS | CLI Guide - Page 219
DGS-6604 m gvrp (Global) gvrp (Global) Use the gvrp interface command to enable GVRP function globally, and use the no gvrp command the GVRP protocol global state. Switch(config)# gvrp Switch(config)# Verify the settings by entering the show gvrp configuration command. CLI Reference Guide 209 - D-Link DGS-6600-48TS | CLI Guide - Page 220
DGS-6604 m gvrp (Interface) gvrp (Interface) Use the gvrp interface command to enable GVRP function for a port, and use the no gvrp . Switch(config)# interface eth3.1 Switch(config-if)# gvrp Verify the settings by entering the show gvrp configuration interface command. CLI Reference Guide 210 - D-Link DGS-6600-48TS | CLI Guide - Page 221
DGS-6604 m gvrp advertise (Interface) gvrp advertise (Interface) Use the gvrp advertise command to specify that this VLAN will be advertised )# interface eth4.1 Switch(config-if)# gvrp advertise 1000 Verify the settings by entering the show gvrp configuration command. CLI Reference Guide 211 - D-Link DGS-6600-48TS | CLI Guide - Page 222
DGS-6604 m gvrp advertise (VLAN) gvrp advertise (VLAN) Use the gvrp advertise command to specify that this VLAN will be advertised out by . Switch(config)# VLAN 1000 Switch(config-VLAN)# gvrp advertise Verify the settings by entering the show gvrp configuration command. CLI Reference Guide 212 - D-Link DGS-6600-48TS | CLI Guide - Page 223
DGS-6604 m gvrp dynamic-vlan-creation gvrp dynamic-vlan-creation Use the gvrp dynamic-vlan-creation command to enable dynamic VLAN Switch(config)# gvrp Switch(config)# gvrp dynamic-vlan-creation Verify the settings by entering the show gvrp configuration command. CLI Reference Guide 213 - D-Link DGS-6600-48TS | CLI Guide - Page 224
DGS-6604 m gvrp forbidden gvrp forbidden Use the gvrp forbidden command to specify the port as a forbidden member. Use the no Switch(config)# interface eth3.1 Switch(config-if)# gvrp forbidden Verify the settings by entering the show gvrp configuration interface command CLI Reference Guide 214 - D-Link DGS-6600-48TS | CLI Guide - Page 225
DGS-6604 m gvrp timer Use the gvrp timer command to set the GVRP timer value for a port. gvrp timer {join | leave | leave-all} )# interface eth3.1 Switch(config-if)# gvrp timer leave-all 500 Verify the settings by entering the show gvrp configuration interface command. CLI Reference Guide 215 - D-Link DGS-6600-48TS | CLI Guide - Page 226
DGS-6604 heH lp help Syntax Default Command Mode Usage Guideline Example help To display a brief description of the help system, use the Partial help is provided when an abbreviated argument is entered and you want to know what arguments match the input (e.g. 'show ve?'.) CLI Reference Guide 216 - D-Link DGS-6600-48TS | CLI Guide - Page 227
DGS-6604 host area host area Use the host area command to configure a stub host is configured. Router configuration Using this command, specific host routes can be advertised in the router-LSA as stub link. This following example shows how to configure a stub host 172.16.10.100 at area 1. Switch# - D-Link DGS-6600-48TS | CLI Guide - Page 228
DGS-6604 hybrid vlan VLAN-ID hybrid vlan VLAN-ID Use the hybrid VLAN command to set the VLAN characteristic. It sets the interface as 1000. Switch(config)# interface eth3.1 Switch(config-if)# hybrid vlan 1000 tagged Verify the settings by entering the show vlan command. CLI Reference Guide 218 - D-Link DGS-6600-48TS | CLI Guide - Page 229
DGS-6604 ingress-checking inGgress-checking Use the ingress-checking to enable ingress frame checking at a port. Use the no ingress- 4.1. Switch(config)# interface eth4.1 Switch(config-if)# ingress-checking Verify the settings by entering the show vlan interface command. CLI Reference Guide 219 - D-Link DGS-6600-48TS | CLI Guide - Page 230
DGS-6604 instance instance To map a VLAN or a set of VLANs to a single Multiple Spanning Tree (MST) instance, use the instance command. configuration Switch(config-mst)# instance 5 vlan 1100 Verify the settings by entering the show spanning-tree mst configuration command. CLI Reference Guide 220 - D-Link DGS-6600-48TS | CLI Guide - Page 231
DGS-6604 interface interface Enter the interface command to go into interface configuration mode. The command executed in this mode will VLAN. This example shows how to enter the interface configuration mode for eth2.5: Switch(config)# interface eth2.5 Switch(config-if)# CLI Reference Guide 221 - D-Link DGS-6600-48TS | CLI Guide - Page 232
DGS-6604 interface range interface range Enter the interface range command to go into interface range configuration mode. The command the interface configuration mode for a range of ports from eth2.1-2.5. Switch(config)# interface range eth2.1-2.5 Switch(config-if)# CLI Reference Guide 222 - D-Link DGS-6600-48TS | CLI Guide - Page 233
DGS-6604 interface tunnel interface tunnel Use the interface tunnel configuration command to add a tunnel and to enter the interface tunnel 2 Switch (config-if)# The following example will remove IPv6 tunnel 2. Switch(config)# no interface tunnel 2 Switch (config)# CLI Reference Guide 223 - D-Link DGS-6600-48TS | CLI Guide - Page 234
DGS-6604 ip access-group ip access-group Use the ip access-group command to specify the IP access-list to be applied to an )# interface eth3.2 Switch(config-if)#ip access-group Strict-Control Verify the settings by entering the show access-group privileged EXEC command. CLI Reference Guide 224 - D-Link DGS-6600-48TS | CLI Guide - Page 235
DGS-6604 ip access-list ip access-list Use the command to create or modify an IP access list. This command enters the user interface into -ip-acl)#permit host 172.16.65.193 any Switch(config-ip-acl)# Verify the settings by entering the show access-list command. CLI Reference Guide 225 - D-Link DGS-6600-48TS | CLI Guide - Page 236
DGS-6604 ip address ip address Use ip address to set a primary or secondary IP address for an interface, or acquire an IP address on an set 10.108.1.27 as the primary address and 192.31.7.17 and 192.31.8.17 as the secondary addresses for VLAN 100: CLI Reference Guide 226 - D-Link DGS-6600-48TS | CLI Guide - Page 237
DGS-6604 Switch# configure terminal Switch(config)# interface vlan100 Switch(config-if)# ip address 10.108.1.27 255.255.255.0 Switch(config-if)# ip .31.8.17 255.255.255.0 secondary Switch(config)# end Verify the settings by entering the show ip interface command. ip address CLI Reference Guide 227 - D-Link DGS-6600-48TS | CLI Guide - Page 238
DGS-6604 ip address (management port) ip address (management port) Use the command to set the IP address of the Management Port. Use the no config)#mgmt-if Switch(mgmt-if)#ip address 10.1.1.1/8 Switch(mgmt-if)#end Verify the settings by entering the show mgmt-if command. CLI Reference Guide 228 - D-Link DGS-6600-48TS | CLI Guide - Page 239
DGS-6604 ip address-list ip address-list Use this command to specify the IP address range in a DHCP address pool and one of which is -dhcp)# no ip address-list 10.1.1.200 Switch(config-dhcp)# Verify the address pool is added with the show ip dhcp pool command. CLI Reference Guide 229 - D-Link DGS-6600-48TS | CLI Guide - Page 240
DGS-6604 ip dhcp screening ports ip dhcp screening ports Use the command to configure the state of the function for filtering of the DHCP server screening function on port eth4.1 and eth5.3: switch# configure terminal switch(config)#ip dhcp screening ports eth4.1,eth5.3 CLI Reference Guide 230 - D-Link DGS-6600-48TS | CLI Guide - Page 241
DGS-6604 ip dhcp screening ip dhcp screening Use this command to add/delete the DHCP server/client binding entry. ip dhcp screening server-ip 34 switch#configure terminal switch(config)#ip dhcp screening server-ip 10.1.1.1 client-mac 00-08-01-0203-04 ports eth4.1-4.34 CLI Reference Guide 231 - D-Link DGS-6600-48TS | CLI Guide - Page 242
DGS-6604 ip dhcp screening trap-log ip dhcp screening trap-log Used to enable trap/log function and use the no form to The following example shows to enable trap/log function of DHCP screening: switch#configure terminal switch(config)# ip dhcp screening trap-log CLI Reference Guide 232 - D-Link DGS-6600-48TS | CLI Guide - Page 243
DGS-6604 ip dhcp snooping ip dhcp snooping during the relay agent relays the packet. To enable the DHCP relay service, relay agent service must be enabled by service dhcp command, and the server address to relay the packet must be )# no ip dhcp snooping Switch(config)# CLI Reference Guide 233 - D-Link DGS-6600-48TS | CLI Guide - Page 244
DGS-6604 ip dhcp snooping information option ip dhcp snooping information option Use this command to globally allow DHCP packets with allow-untrusted port: . Switch# configure terminal Switch(config)# no ip dhcp snooping information option allow-untrusted Switch(config)# CLI Reference Guide 234 - D-Link DGS-6600-48TS | CLI Guide - Page 245
DGS-6604 ip dhcp snooping trust ip dhcp snooping trust Use this command to configure a port as interface trusted for DHCP snooping. Use to enable DHCP snooping trust for port 3.3: Switch(config)# interface eth3.3 Switch(config-if)# ip dhcp snooping trust Switch(config)# CLI Reference Guide 235 - D-Link DGS-6600-48TS | CLI Guide - Page 246
DGS-6604 ip dhcp screening suppress-duration ip dhcp screening suppress-duration Used to set the suppressed duration for trap/log and use shows to specify the suppress time to 20 minutes: switch#configure terminal switch(config)# ip dhcp screening suppress-duration 20 CLI Reference Guide 236 - D-Link DGS-6600-48TS | CLI Guide - Page 247
DGS-6604 ip arp inspection trust ip arp inspection trust Use the command to trust an interface for dynamic ARP inspection. Use the be trusted for DAI: Switch# configure terminal Switch(config)# interface eth3.3 Switch(config-if)# ip arp inspection trust Switch(config-if)# CLI Reference Guide 237 - D-Link DGS-6600-48TS | CLI Guide - Page 248
DGS-6604 ip arp inspection validate ip arp inspection validate Use the command to specify the additional checks to be performed during terminal Switch(config)# ip arp inspection validate src-mac Switch(config)# This example shows how to disable source MAC validation: CLI Reference Guide 238 - D-Link DGS-6600-48TS | CLI Guide - Page 249
DGS-6604 Switch# configure terminal Switch(config)# no ip arp inspection validate src-mac Switch(config)# ip arp inspection validate CLI Reference Guide 239 - D-Link DGS-6600-48TS | CLI Guide - Page 250
DGS-6604 ip arp inspection vlan ip arp inspection vlan Use the command to enable specific VLANs for dynamic ARP inspection. Use the example shows how to enable ARP inspection on VLAN2: Switch# configure terminal Switch(config)# ip arp inspection vlan 2 Switch(config)# CLI Reference Guide 240 - D-Link DGS-6600-48TS | CLI Guide - Page 251
DGS-6604 ip verify source vlan dhcp- port ACL. Port ACL is a hardware mechanism and its entry can come from either the manual configured entry or the DHCP snooping binding database. The packet fails to pass the validation will -snooping port-security Switch(config-if)# CLI Reference Guide 241 - D-Link DGS-6600-48TS | CLI Guide - Page 252
DGS-6604 ip source binding ip source binding Use this command to create a static entry used for IP source guard. Use the no form of interface eth3.10: Switch# configure terminal Switch(config)# ip source binding 00-01-02-03-04-05 vlan 2 10.1.1.1 interface eth3.10 Switch# CLI Reference Guide 242 - D-Link DGS-6600-48TS | CLI Guide - Page 253
DGS-6604 This example shows how to delete an IP Source Guard entry with IP address 10.1.1.1 and MAC address 00-01-02-03-04-05, eth3.10: Switch# configure terminal Switch(config)# no ip source binding 00-01-02-03-04-05 vlan 2 10.1.1.1 interface eth3.10 Switch# CLI Reference Guide 243 - D-Link DGS-6600-48TS | CLI Guide - Page 254
DGS-6604 ip as-path access-list ip as-path access-list Use this command to define a BGP Autonomous System (AS) path access list. Use ^65535$ Switch(config)# ip as-path access-list mylist permit .* Verify the settings by entering the show ip as-path access-list command. CLI Reference Guide 244 - D-Link DGS-6600-48TS | CLI Guide - Page 255
DGS-6604 ip community-list ip community-list Use this command to add a community list entry. Use the no form of this command to delete lists bonded at the specified access list will be removed. This example (on the next page) shows how to configure a community list CLI Reference Guide 245 - D-Link DGS-6600-48TS | CLI Guide - Page 256
DGS-6604 ip community-list named "mycommlist" that permit routes from network 10 in autonomous system 50000: Switch(config)# ip community-list mycommlist permit 50000:10 Verify the settings by entering the show ip community-list command. CLI Reference Guide 246 - D-Link DGS-6600-48TS | CLI Guide - Page 257
DGS-6604 ip dhcp snooping verify MAC-address ip dhcp snooping verify MAC-address Use this command to enable the verification that address in a DHCP packet matches the client hardware address Switch# configure terminal Switch(config)# ip dhcp snooping verify mac-address CLI Reference Guide 247 - D-Link DGS-6600-48TS | CLI Guide - Page 258
DGS-6604 ip dhcp snooping vlan ip dhcp snooping vlan Use this command to enable DHCP snooping on a VLAN or a group of VLANs. Use This example shows how to enable DHCP snooping on vlan10: Switch# configure terminal Switch(config)# ip dhcp snooping vlan 10 Switch(config)# CLI Reference Guide 248 - D-Link DGS-6600-48TS | CLI Guide - Page 259
DGS-6604 This example shows how to disable DHCP snooping on vlan10: Switch# configure terminal Switch(config)# no ip dhcp snooping vlan 10 Switch( DHCP snooping on range of VLAN: Switch# configure terminal Switch(config)# no ip dhcp snooping vlan 10,15-18 Switch(config)# CLI Reference Guide 249 - D-Link DGS-6600-48TS | CLI Guide - Page 260
DGS-6604 ip dhcp ping packets ip dhcp ping packets User this command to specify the number of packets that the DHCP server will . The following is a sample of configuring the number of ping packets as 3. switch# configure terminal switch(config)# ip dhcp ping packets 3 CLI Reference Guide 250 - D-Link DGS-6600-48TS | CLI Guide - Page 261
DGS-6604 ip dhcp ping timeout ip dhcp ping timeout Use this command to specify how long the DHCP server will wait for the ping it pinged. The following is sample of configuring the ping timeout as 100. switch# configure terminal switch(config)# ip dhcp ping timeout 100 CLI Reference Guide 251 - D-Link DGS-6600-48TS | CLI Guide - Page 262
DGS-6604 ip dhcp pool ip dhcp pool Use this command to configure a DHCP address pool on a DHCP Server and enter the DHCP pool to the host. The following example configures the address pool named "pool1". switch# configure terminal switch(config)# ip dhcp pool pool1 CLI Reference Guide 252 - D-Link DGS-6600-48TS | CLI Guide - Page 263
DGS-6604 ip dhcp relay ip dhcp relay Use this command to enable Dynamic Host Configuration Protocol (DHCP) relay agent features on the > enable Switch# configure terminal Switch(config)# ip dhcp relay Verify the settings by entering the show ip dhcp relay command. CLI Reference Guide 253 - D-Link DGS-6600-48TS | CLI Guide - Page 264
DGS-6604 ip dhcp relay address ip dhcp relay address Use this command to specify the DHCP relay server IP address. Use the no form (config)# interface vlan100 Switch(config-if)# ip dhcp relay address 10.1.1.1 Verify the settings by entering the show ip dhcp relay command. CLI Reference Guide 254 - D-Link DGS-6600-48TS | CLI Guide - Page 265
DGS-6604 ip dhcp relay hops ip dhcp relay hops Use this command to configure the maximum number of relay hops that the DHCP relay hops 5: Switch# configure terminal Switch(config)#ip dhcp relay hops 5 Verify the settings by entering the show ip dhcp relay command. CLI Reference Guide 255 - D-Link DGS-6600-48TS | CLI Guide - Page 266
DGS-6604 ip dhcp relay information check ip dhcp relay information check Use this command to configure the DHCP relay agent to validate # configure terminal Switch(config)# ip dhcp relay information check Verify the settings by entering the show ip dhcp relay command. CLI Reference Guide 256 - D-Link DGS-6600-48TS | CLI Guide - Page 267
DGS-6604 ip dhcp relay information option ip dhcp relay information option Use this command to enable the insertion of the relay agent information Remote ID Type Length MAC Address Value 2 8 0 6 M1 M2 M3 M4 M5 M6 MAC address: the switch's system MAC address. CLI Reference Guide 257 - D-Link DGS-6600-48TS | CLI Guide - Page 268
DGS-6604 Example ip dhcp relay information option This example shows how to enable insertion of the option-82 field during the relay Switch# configure terminal Switch(config)# ip dhcp relay information option Verify the settings by entering the show ip dhcp relay command. CLI Reference Guide 258 - D-Link DGS-6600-48TS | CLI Guide - Page 269
DGS-6604 ip dhcp relay information policy ip dhcp relay information policy Use this command to configure the information re-forwarding policy terminal Switch(config)# ip dhcp relay information policy drop Verify the settings by entering the show ip dhcp relay command. CLI Reference Guide 259 - D-Link DGS-6600-48TS | CLI Guide - Page 270
DGS-6604 ip dhcp relay information trust-all ip dhcp relay information trust-all Use this global command to direct the DHCP relay ip dhcp relay information trust-all Swtich(config)# Verify the settings by entering the show ip dhcp relay information trustedsources command CLI Reference Guide 260 - D-Link DGS-6600-48TS | CLI Guide - Page 271
DGS-6604 ip dhcp relay information trusted ip dhcp relay information trusted Use this interface command to direct the DHCP relay agent information trusted Swtich(config-if)# end Verify the settings by entering the show ip dhcp relay information trustedsources command. CLI Reference Guide 261 - D-Link DGS-6600-48TS | CLI Guide - Page 272
DGS-6604 ip dvmrp ip dvmrp no ip dvmrp Syntax Default Command Mode Usage Guideline Example ip dvmrp Use this command to enable DVMRP interface VLAN 1. Switch(config)# interface vlan1 Switch(config-if)# ip dvmrp Verify the settings by the show ip dvmrp interface command. CLI Reference Guide 262 - D-Link DGS-6600-48TS | CLI Guide - Page 273
DGS-6604 ip dvmrp metric ip dvmrp metric Use this command to configure the metric value on the current interface. ip dvmrp metric interface. Switch(config)# interface vlan1 Switch(config-if)# ip dvmrp metric 2 Verify the settings by the show ip dvmrp interface command. CLI Reference Guide 263 - D-Link DGS-6600-48TS | CLI Guide - Page 274
DGS-6604 ip http server ip http server Use this command to enable HTTP server. Use the no form of the command to disable HTTP example will disable the http server Switch(config)# no ip http server Verify the settings by entering the show system protocol-state command. CLI Reference Guide 264 - D-Link DGS-6600-48TS | CLI Guide - Page 275
DGS-6604 ip http service-port ip http service-port Use this command to specify the HTTP service port. And use the default command to return the service port to 80. ip http service-port TCP-PORT default ip http service ip http service-port 100 Verify the settings by entering the show - D-Link DGS-6600-48TS | CLI Guide - Page 276
DGS-6604 ip igmp access-group ip igmp access-group Using the ip igmp access- not only by group addresses reported, but by group and source addresses. This example shows how to restrict the serviced IGMP group for VLAN 1000 to group 226.1.1.1. In the following example, at first, create an IP basic - D-Link DGS-6600-48TS | CLI Guide - Page 277
DGS-6604 ip igmp access-group Switch#configure terminal Switch(config)# ip access-list igmp_filter Switch(config-ip-acl)#permit any 226.1.1.1 255 )# ip igmp access-group igmp_filter Switch(config-if)# end Verify the settings by entering the show ip igmp interface command. CLI Reference Guide 267 - D-Link DGS-6600-48TS | CLI Guide - Page 278
DGS-6604 ip igmp last-member-query-interval ip igmp last-member-query-interval Use this command to configure the interval at which the ip igmp last-member-query-interval 2000 Switch(config-if)# end Verify the settings by entering the show ip igmp interface command. CLI Reference Guide 268 - D-Link DGS-6600-48TS | CLI Guide - Page 279
DGS-6604 ip igmp query-interval ip igmp query-interval Use this command to configure the interval at which the router sends IGMP general-query config-if)# ip igmp query-interval 300 Switch(config-if)# end Verify the settings by entering the show ip igmp interface command. CLI Reference Guide 269 - D-Link DGS-6600-48TS | CLI Guide - Page 280
DGS-6604 ip igmp query-max-response-time ip igmp query-max-response-time Use this command to configure the maximum response time advertised in )# ip igmp query-max-response-time 10 Switch(config-if)# end Verify the settings by entering the show ip igmp interface command. CLI Reference Guide 270 - D-Link DGS-6600-48TS | CLI Guide - Page 281
DGS-6604 ip igmp robustness-variable ip igmp robustness-variable Use this command to tune for the expected packet loss on a network, i.e. the -if)# ip igmp robustness-variable 5 Switch(config-if)# end Verify the settings by entering the show ip igmp interface command. CLI Reference Guide 271 - D-Link DGS-6600-48TS | CLI Guide - Page 282
DGS-6604 ip igmp snooping ip igmp snooping Use this command to enable IGMP Snooping function on the switch. Use the no form of this all of the existing VLANs. As a VLAN is deleted, the related IGMP snooping setting for the VLAN is also removed from system configuration. CLI Reference Guide 272 - D-Link DGS-6600-48TS | CLI Guide - Page 283
DGS-6604 Examples ip igmp snooping This example shows how to globally enable IGMP Snooping for all existing VLANs. Switch(config)# ip igmp snooping -if)# ip igmp snooping Switch(config-if)# end Switch# Verify the settings by entering the show ip igmp snooping command. CLI Reference Guide 273 - D-Link DGS-6600-48TS | CLI Guide - Page 284
DGS-6604 ip igmp snooping (multicast router) ip igmp snooping (multicast router) Use this command to configure the specified interface(s) as snooping {mrouter-designate | mrouter-not-allowed} command, an error message is displayed if the designated port is ineligible. CLI Reference Guide 274 - D-Link DGS-6600-48TS | CLI Guide - Page 285
DGS-6604 Examples ip igmp snooping (multicast router) This example shows how to add a interface vlan4 Switch(config-if)# ip igmp snooping mrouter-designate interface vlan5 % Interface type not support vlan5 Switch(config-if)# exit Switch(config)# Verify the settings by entering the show ip igmp - D-Link DGS-6600-48TS | CLI Guide - Page 286
DGS-6604 ip igmp snooping immediate-leave ip igmp snooping immediate-leave Use this command to configure the IGMP Snooping immediate-leave function ip igmp snooping immediate-leave Switch(config-if)# end Verify the settings by entering the show ip igmp snooping command. CLI Reference Guide 276 - D-Link DGS-6600-48TS | CLI Guide - Page 287
DGS-6604 ip igmp snooping querier ip igmp query packet in order to express that it remains in the specified group. The maximum response time instructs the client to report within the time period specified. If the IGMP snooping entity does not ip igmp snooping command. CLI Reference Guide 277 - D-Link DGS-6600-48TS | CLI Guide - Page 288
DGS-6604 ip igmp snooping static-group ip igmp snooping static-group Use this command to configure an IGMP snooping static group. Use -group. When the associated VLAN is deleted, the related IGMP snooping static-group entries are also removed from system configuration. CLI Reference Guide 278 - D-Link DGS-6600-48TS | CLI Guide - Page 289
DGS-6604 Example ip igmp snooping static-group The following example, on the next page, shows how to statically add group and/ or igmp snooping static-group 226.1.2.6 source 10.1.2.3 interface eth3.5 Verify the settings by entering the show ip igmp snooping group command. CLI Reference Guide 279 - D-Link DGS-6600-48TS | CLI Guide - Page 290
DGS-6604 ip igmp version ip igmp version Use this command to change the IGMP version on the specified interface. ip igmp version {1|2|3} Syntax (config-if)# ip igmp version 3 Switch(config-if)# end Verify the settings by entering the show ip igmp interface command. CLI Reference Guide 280 - D-Link DGS-6600-48TS | CLI Guide - Page 291
DGS-6604 ip mroute Use this command to create a multicast static route (mroute). Use the no form of this command to delete the route. configures the multicast data source within a network number 192.168.8.0/24 to be discarded. Switch(config)#ip mroute 192.168.8.0/24 null CLI Reference Guide 281 - D-Link DGS-6600-48TS | CLI Guide - Page 292
DGS-6604 ip mroute The following example removes a previously configured ip mroute entry of 192.168.8.0/24. Switch(config)#no ip mroute 192.168.8.0/24 Verify the settings using the show running-config command. CLI Reference Guide 282 - D-Link DGS-6600-48TS | CLI Guide - Page 293
DGS-6604 ip mtu ip mtu BYTES ip mtu Use this command to set the MTU value in TCP/IP stack. Use the default form to Swtich(config)# interface vlan4 Switch(config-if)# default ip mtu Switch(config-if)# end Verify the settings by entering the show interface command. CLI Reference Guide 283 - D-Link DGS-6600-48TS | CLI Guide - Page 294
DGS-6604 ip mtu (management port) ip mtu (management port) Use this command to set the IP layer maximum transfer unit of the Management Port. Use (config)#mgmt-if Switch(mgmt-if)#ip mtu 1600 Switch(mgmt-if)#end Verify the settings by entering the show mgmt-if command CLI Reference Guide 284 - D-Link DGS-6600-48TS | CLI Guide - Page 295
DGS-6604 ip multicast-routing ip multicast-routing Use this command to enable IP multicast routing. Use the no form of this command to how to enable IP multicast routing. Switch(config)# ip multicast-routing Verify the settings by the show system protocol-state command. CLI Reference Guide 285 - D-Link DGS-6600-48TS | CLI Guide - Page 296
DGS-6604 ip ospf authentication ip ospf authentication Use this command to send and receive OSPF packets with the specified authentication method. Switch(config-if)# ip ospf authentication message-digest Verify the settings by entering the show ip ospf interface command. CLI Reference Guide 286 - D-Link DGS-6600-48TS | CLI Guide - Page 297
DGS-6604 ip ospf authentication-key ip ospf authentication-key Use this command to specify an OSPF authentication password for the neighboring -key test Switch(config-if)# ip ospf authentication Verify the settings by entering the show ip ospf interface command CLI Reference Guide 287 - D-Link DGS-6600-48TS | CLI Guide - Page 298
This cost is advertised as the link cost in the router link advertisement. The cost is inversely proportional to the bandwidth of an interface. The cost can be either manually assigned or be automatically determined. settings by entering the show ip ospf interface command. CLI Reference Guide 288 - D-Link DGS-6600-48TS | CLI Guide - Page 299
DGS-6604 ip ospf dead-interval ip ospf dead-interval Use this command to set the interval during which no hello packets are received config)# interface vlan1 Switch(config-if)# ip ospf dead-interval 10 Verify the settings by entering the show ip ospf interface command. CLI Reference Guide 289 - D-Link DGS-6600-48TS | CLI Guide - Page 300
DGS-6604 ip ospf hello-interval ip ospf hello-interval Use this command to specify the interval between hello packets. The no-form of (config)# interface vlan1 Switch(config-if)# ip ospf hello-interval 3 Verify the settings by entering the show ip ospf interface command. CLI Reference Guide 290 - D-Link DGS-6600-48TS | CLI Guide - Page 301
DGS-6604 ip ospf message-digest-key ip ospf message-digest-key Use this command to register an MD5 key for OSPF MD5 authentication. Use Switch(config-if)# ip ospf message-digest-key 10 md5 yourpass Verify the settings by entering the show ip ospf interface command. CLI Reference Guide 291 - D-Link DGS-6600-48TS | CLI Guide - Page 302
DGS-6604 ip ospf priority ip ospf priority Use this command to set the router priority to determine the designated router for the Switch(config)# interface vlan1 Switch(config-if)# ip ospf priority 3 Verify the settings by entering the show ip ospf interface command. CLI Reference Guide 292 - D-Link DGS-6600-48TS | CLI Guide - Page 303
DGS-6604 ip ospf retransmit-interval ip ospf retransmit-interval Use this command to specify the time between link-state advertisement (LSA) retransmissions for adjacencies belonging to the interface. The no the settings by entering the show ip ospf interface command CLI Reference Guide 293 - D-Link DGS-6600-48TS | CLI Guide - Page 304
DGS-6604 ip ospf shutdown ip ospf shutdown To initiate a graceful shutdown of Open Shortest Path First (OSPF) protocol at interface level, OSPF protocol shutdown on the layer 3 interface (VLAN 1): Switch(config)# router ospf Switch(config-router)# ip ospf shutdown vlan1 CLI Reference Guide 294 - D-Link DGS-6600-48TS | CLI Guide - Page 305
DGS-6604 ip ospf transmit-delay ip ospf transmit-delay Use this command to set the estimated time it takes to transmit a link-stateupdate packet on the interface. Use the no parameter with this command to Verify the settings by entering the show ip ospf interface command. CLI Reference Guide 295 - D-Link DGS-6600-48TS | CLI Guide - Page 306
DGS-6604 ip ospf mtu-ignore ip ospf mtu-ignore To disable OSPF MTU mismatch detection on receiving DBD packets, use the ip MTU mismatch detection on receiving DBD packets. Switch# configure terminal Switch(config)# interface vlan1 Switch(config-if)# ip ospf mtu-ignore CLI Reference Guide 296 - D-Link DGS-6600-48TS | CLI Guide - Page 307
DGS-6604 ip pim ip pim Enable PIM on the interface for either sparse mode or dense mode operation. Use the no form of the interface. Switch(config)# interface vlan1 Switch(config-if)# ip pim sparse-mode Verify the settings by entering the show ip pim interface command. CLI Reference Guide 297 - D-Link DGS-6600-48TS | CLI Guide - Page 308
DGS-6604 ip pim accept-register ip pim accept-register To configure a candidate rendezvous point (RP) router to filter PIM register messages, use acl)# exit Switch(config)# ip pim accept-register source-list Summer-Movie Verify the settings by the show ip pim command. CLI Reference Guide 298 - D-Link DGS-6600-48TS | CLI Guide - Page 309
DGS-6604 ip pim bsr-candidate ip pim bsr-candidate Use this command to configure the router to advertise itself as a candidate bootstrap router (BSR). group address, and the addresses of the candidate RPs from the mappings, and gives as output, one RP address to be used. CLI Reference Guide 299 - D-Link DGS-6600-48TS | CLI Guide - Page 310
DGS-6604 Example ip pim bsr-candidate The following example shows how to configure the IP address of the router on VLAN 1 to be a candidate BSR of 192: Switch(config)# ip pim bsr-candidate vlan1 20 192 Switch(config)# Verify the settings by using the show ip pim command. CLI Reference Guide 300 - D-Link DGS-6600-48TS | CLI Guide - Page 311
DGS-6604 ip pim dr-priority ip pim dr-priority Use this command to change the Designated Router Priority value inserted into the DR (config)# interface vlan1 Switch(config-if)# ip pim dr-priority 200 Verify the settings by entering the show ip pim interface command. CLI Reference Guide 301 - D-Link DGS-6600-48TS | CLI Guide - Page 312
DGS-6604 ip pim join-prune-interval ip pim average number of multicast route entries for the attached network or link (for example, the period would be longer for lower-speed links, or for routers in the center of the network that expect the show ip pim interface command. CLI Reference Guide 302 - D-Link DGS-6600-48TS | CLI Guide - Page 313
DGS-6604 ip pim prune-limit-interval ip pim prune-limit-interval Use this command to configure the time interval for the prune limit interface vlan1 Switch(config-if)# ip pim prune-limit-interval 120 Verify the settings by entering the show ip pim interface command. CLI Reference Guide 303 - D-Link DGS-6600-48TS | CLI Guide - Page 314
DGS-6604 ip pim query-interval ip pim query-interval Use this command to configure the frequency of PIM hello message. ip pim query- (config)# interface vlan1 Switch(config-if)# ip pim query-interval 45 Verify the settings by entering the show ip pim interface command. CLI Reference Guide 304 - D-Link DGS-6600-48TS | CLI Guide - Page 315
DGS-6604 ip pim register-checksum-include-data ip pim register-checksum-include-data Use this command to configure the option to calculate the over whole packet. Switch(config)# ip pim register-checksum-include-data Verify the settings by using the show ip pim command. CLI Reference Guide 305 - D-Link DGS-6600-48TS | CLI Guide - Page 316
DGS-6604 ip pim register-suppresion ip pim register-suppresion Use this command to configure the register-suppression time. ip pim register-suppression time to 30 seconds. Switch(config)# ip pim register-suppression 30 Verify the settings by the show ip pim command. CLI Reference Guide 306 - D-Link DGS-6600-48TS | CLI Guide - Page 317
DGS-6604 ip pim rp-address ip pim rp-address Use this command to statically configure the rendezvous point (RP) address for multicast groups. To remove (config)# ip pim rp-address 10.90.90.90 group-list PIM-Control Verify the settings by using the show ip pim command. CLI Reference Guide 307 - D-Link DGS-6600-48TS | CLI Guide - Page 318
DGS-6604 ip pim rp-candidate ip pim parts of the PIM domain. That is, a stub router that relies on an on-demand dialup link to connect to the rest of the PIM domain is not a good candidate RP. The following example Control, which specifies the group prefix (239.0.0.0/8), is CLI Reference Guide 308 - D-Link DGS-6600-48TS | CLI Guide - Page 319
DGS-6604 ip pim rp-candidate associated with the RP that has the address identified by VLAN interface 1 and with priority 3. Switch(config)# ip (config)# ip pim rp-candidate vlan1 group-list PIM-Control priority 3 Verify the settings by using the show ip pim command. CLI Reference Guide 309 - D-Link DGS-6600-48TS | CLI Guide - Page 320
DGS-6604 ip pim state-refresh origination-interval ip pim state-refresh origination-interval Configure a PIM-DM State-Refresh origination interval if)# ip pim state-refresh origination-interval 100 Verify the settings by entering the show ip pim interface command. CLI Reference Guide 310 - D-Link DGS-6600-48TS | CLI Guide - Page 321
DGS-6604 ip policy route-map ip policy route-map Use the command to specify a route map as the routing policy on an interface,. To disable time. Example: user can find ipv6 long prefix route information, but the packet will still be routed to the default interface via PBR. CLI Reference Guide 311 - D-Link DGS-6600-48TS | CLI Guide - Page 322
DGS-6604 Examples ip policy route-map The following example set up routing policy to route the packets that match the IP access list name pbr- (config-if)#ip policy route-map pbr-map Switch(config-if)#exit You can verify your settings by entering show ip policy command. CLI Reference Guide 312 - D-Link DGS-6600-48TS | CLI Guide - Page 323
DGS-6604 ip rip authentication key-chain ip rip authentication key-chain Use this command to enable authentication for RIP Version 2 packets is performed on the interface. This command also specifies that the interface will use the key chain for authentication. CLI Reference Guide 313 - D-Link DGS-6600-48TS | CLI Guide - Page 324
DGS-6604 Example ip rip authentication key-chain The following example configures a key chain named chain1. Key1 named "forkey1string" will be accepted from duration 3600 Switch(config-keychain-key)# exit Verify the settings by entering the show ip protocols rip command. CLI Reference Guide 314 - D-Link DGS-6600-48TS | CLI Guide - Page 325
DGS-6604 ip rip authentication mode ip rip authentication are configured are valid interfaces for this command. RIP Version 1 does not support authentication. This command only affects RIPv2. The following example shows how to configure the show ip rip interface command. CLI Reference Guide 315 - D-Link DGS-6600-48TS | CLI Guide - Page 326
DGS-6604 ip rip receive version ip rip receive version Use this command to specify a RIP version to receive on each interface. Use the no Switch(config-if)# ip rip receive version 1 Switch(config-if)# end Verify the settings by entering the show ip rip interface command. CLI Reference Guide 316 - D-Link DGS-6600-48TS | CLI Guide - Page 327
DGS-6604 ip rip send version ip rip send version Use this command to specify a RIP version to send on an interface basis. Use the no vlan100 Switch(config-if)# ip rip send version 2 Switch(config-if)# end Verify the settings by entering the show ip rip interface command. CLI Reference Guide 317 - D-Link DGS-6600-48TS | CLI Guide - Page 328
DGS-6604 ip rip v2-broadcast ip rip v2-broadcast Use this command to allow Routing Information Protocol (RIP) Version 2 update packets to be Switch(config-if)# ip rip v2-broadcast Switch(config-if)# end Verify the settings by entering the show ip rip interface command. CLI Reference Guide 318 - D-Link DGS-6600-48TS | CLI Guide - Page 329
DGS-6604 ip route ip route Use ip route to add a static route entry. Use the no form of the command to remove a static route entry entry with next-hop 10.1.1.254: Switch(config)# ip route 0.0.0.0/0 10.1.1.254 Verify the settings by entering the show ip route command. CLI Reference Guide 319 - D-Link DGS-6600-48TS | CLI Guide - Page 330
DGS-6604 ip route multi-path ip route multi-path Use ip route multi-path to enable multiple paths for same route. Use the no form to disable multiple paths function. Switch(config)# no ip route multi-path Verify the settings by entering the show ip route summary command. CLI Reference Guide 320 - D-Link DGS-6600-48TS | CLI Guide - Page 331
DGS-6604 ip ssh ip ssh Use this command to configure Secure Shell (SSH) control parameters or enable the SSH service on the switch. Use the no ip ssh command to disable the SSH service. ip ssh [ timeout SECONDS | authentication-retries NUMBER | service ) allowable. CLI Reference Guide 321 - D-Link DGS-6600-48TS | CLI Guide - Page 332
DGS-6604 Examples This example shows how to enable the SSH service. ip ssh Switch# configure terminal Switch(config)# how to change the service-port to 3000. The SSH client must connect using this service port number. Switch# configure terminal Switch(config)# ip ssh service-port 3000 Verify the - D-Link DGS-6600-48TS | CLI Guide - Page 333
DGS-6604 ip telnet server ip telnet server Use this command to enable the TELNET server function. Use the no form of the command to enable telnet server function. Switch(config)# ip telnet server Verify the settings by entering the show system protocol-state command. CLI Reference Guide 323 - D-Link DGS-6600-48TS | CLI Guide - Page 334
DGS-6604 ip telnet service-port ip telnet service-port Use this command to specify the service port for the TELNET server. Use the default command to return the service port to 23. ip telnet service-port TCP-PORT default ip telnet service service port to 3000. Switch(config)# ip telnet service- - D-Link DGS-6600-48TS | CLI Guide - Page 335
DGS-6604 ip trusted-host ip trusted-host Use this command to create the trusted host entries on the switch. Use the no ip trusted-host a trusted host with IP address 163.10.50.126 to snmp access interface. Switch(config)# ip trusted-host 163.10.50.126 snmp CLI Reference Guide 325 - D-Link DGS-6600-48TS | CLI Guide - Page 336
DGS-6604 ip trusted-host This example shows how to remove the trusted host with IP address 163.10.50.126 for all access interfaces. Switch(config)# no ip trusted-host 163.10.50.126 You can verify your settings by entering the show ip trusted-host command. CLI Reference Guide 326 - D-Link DGS-6600-48TS | CLI Guide - Page 337
DGS-6604 ipv6 access-group ipv6 access-group Use the ipv6 access-group command to specify the IPv6 access-list to be applied to an If the remaining resources of filter entry or port operator is insufficient, an error message will display when the access-group is applied. CLI Reference Guide 327 - D-Link DGS-6600-48TS | CLI Guide - Page 338
DGS-6604 Example ipv6 access-group This example shows how to specify the IPv6 access-list ip6-control as an IPv6 access group for eth3.3 Switch(config)# interface eth3.3 Switch(config-if)#ipv6 access-group ip6-control in Verify the settings by entering show access-group. CLI Reference Guide 328 - D-Link DGS-6600-48TS | CLI Guide - Page 339
DGS-6604 ipv6 access-list ipv6 access- IPv6) access-lists. The characters are case sensitive. The maximum number of IPv6 access-list supported by the system is project dependent. An error message will appear if the allowed number is exceeded the show access-list command. CLI Reference Guide 329 - D-Link DGS-6600-48TS | CLI Guide - Page 340
DGS-6604 ipv6 address ipv6 address This command is used to assign the IPv6 address to an interface of the switch. The no Switch # configure terminal Switch (config) # interface vlan1 Switch (config-if) # ipv6 address 3ffe:501:ffff:0:a01:2ff:fe39:1/64 Switch (config-if) # CLI Reference Guide 330 - D-Link DGS-6600-48TS | CLI Guide - Page 341
DGS-6604 ipv6 address ipv6 address This command is used to add or delete an IPv6 address to an interface. The address is configured using an -PD), and then applied using the prefix-name argument. The sub-prefix bits and host bits are defined using the sub-bits argument. CLI Reference Guide 331 - D-Link DGS-6600-48TS | CLI Guide - Page 342
DGS-6604 Examples ipv6 address The following address 3ffe:22:22:22::2/64 will be immediately set. The following example shows how to manually remove a global address from the configuration: Switch > enable Switch # configure terminal Switch ( will be immediately removed. CLI Reference Guide 332 - D-Link DGS-6600-48TS | CLI Guide - Page 343
DGS-6604 ipv6 address (management port) ipv6 address (management port) Use this command to set the IPv6 address of the Management Port. Use the Port. Switch(mgmt-if)# Switch(mgmt-if)#ipv6 address 2000::1/64 Verify the settings by entering the show mgmt-if command CLI Reference Guide 333 - D-Link DGS-6600-48TS | CLI Guide - Page 344
DGS-6604 ipv6 default-gateway (management port) ipv6 default-gateway (management port) Use this command to set the IPv6 address of the IPv6 gateway. Switch(mgmt-if)#ipv6 default-gateway 2000::2 Switch(mgmt-if)# Verify the settings by entering the show mgmt-if command CLI Reference Guide 334 - D-Link DGS-6600-48TS | CLI Guide - Page 345
DGS-6604 ipv6 dhcp client information the time as the planned event nears. • Limit the amount of time before new services or servers are available to the client, such as the addition of a new Simple Network config-if) # ipv6 dhcp client information refresh minimum 7200 CLI Reference Guide 335 - D-Link DGS-6600-48TS | CLI Guide - Page 346
DGS-6604 ipv6 dhcp client pd ipv6 dhcp client pd This command enables a specified IPv6 interface's DHCP client process and it enables the commit option in a solicit message. The DHCP for IPv6 client, server, and relay functions are mutually exclusive on an interface. CLI Reference Guide 336 - D-Link DGS-6600-48TS | CLI Guide - Page 347
DGS-6604 Examples ipv6 dhcp client pd The following example enables prefix delegation, where dhcp-prefix is the general prefix name configured by ipv6 (config-if) # ipv6 dhcp client pd hint 2001:0DB8:1::/48 Switch (config-if) # ipv6 dhcp client pd dhcp-prefix rapid-commit CLI Reference Guide 337 - D-Link DGS-6600-48TS | CLI Guide - Page 348
DGS and it enables DHCP for IPv6 relay service on the interface. When relay service is enabled on an interface, a DHCP address. The following are the two types of relay destination addresses: • A link-scoped unicast or multicast IPv6 address, for which, a user must specify an Reference Guide 338 - D-Link DGS-6600-48TS | CLI Guide - Page 349
DGS-6604 Example ipv6 dhcp relay deletes an output interface for a destination. If all relay destinations are removed, the relay service is disabled on the interface. DHCP for the IPv6 client, server, and relay functions (config-if) # no ipv6 dhcp relay destination CLI Reference Guide 339 - D-Link DGS-6600-48TS | CLI Guide - Page 350
DGS ipv6 enable command. When the interface up, ipv6 enable will also add link-local address to the interface and vice versa. When global address had existed using the "no ipv6 enable" command, it will take no effect (link-local address should not be removed). This example shows how to enable the - D-Link DGS-6600-48TS | CLI Guide - Page 351
DGS-6604 ipv6 hop-limit ipv6 hop-limit This command is used to configure the IPv6 hop limit setting for an interface of setting: Switch > enable Switch # configure terminal Switch (config) # interface vlan1 Switch (config-if) # ipv6 hop-limit 255 Switch (config-if) # CLI Reference Guide 341 - D-Link DGS-6600-48TS | CLI Guide - Page 352
DGS-6604 ipv6 nd managed-config-flag ipv6 nd managed-config-flag This command is used to turn on the IPv6 RA (router : Switch > enable Switch # configure terminal Switch (config) # interface vlan1 Switch (config-if) # ipv6 nd managed-config-flag Switch (config-if) # CLI Reference Guide 342 - D-Link DGS-6600-48TS | CLI Guide - Page 353
DGS-6604 ipv6 nd other-config-flag ipv6 nd other-config-flag This command is used to turn on the IPv6 RA (router : Switch > enable Switch # configure terminal Switch (config) # interface vlan1 Switch (config-if) # ipv6 nd other-config-flag Switch (config-if) # CLI Reference Guide 343 - D-Link DGS-6600-48TS | CLI Guide - Page 354
DGS-6604 ipv6 nd prefix ipv6 nd of the command removes it. ipv6 nd prefix X:X::X:X/M [off-link | no-autoconfig] no ipv6 nd prefix X:X::X:X/M Syntax Description X:X::X:X/M IPv6 network address :ffff:100::/64 30000 20000 Switch (config-if) # CLI Reference Guide 344 - D-Link DGS-6600-48TS | CLI Guide - Page 355
DGS-6604 ipv6 nd ra-interval ipv6 nd ra-interval This command is used to configure the IPv6 RA (router advertisement) interval > enable Switch # configure terminal Switch (config) # interface vlan1 Switch (config-if) # ipv6 nd ra-interval 1500 1000 Switch (config-if) # CLI Reference Guide 345 - D-Link DGS-6600-48TS | CLI Guide - Page 356
DGS-6604 ipv6 nd ra-lifetime ipv6 nd ra-lifetime This command is used to configure the IPv6 RA (router advertisement) lifetime Switch > enable Switch # configure terminal Switch (config) # interface vlan1 Switch (config-if) # ipv6 nd ra-lifetime 9000 Switch (config-if) # CLI Reference Guide 346 - D-Link DGS-6600-48TS | CLI Guide - Page 357
DGS-6604 ipv6 nd reachable-time ipv6 nd reachable-time This command is used to configure IPv6 RA (router advertisement) reachable enable Switch # configure terminal Switch (config) # interface vlan1 Switch (config-if) # ipv6 nd reachable time 3600000 Switch (config-if) # CLI Reference Guide 347 - D-Link DGS-6600-48TS | CLI Guide - Page 358
DGS-6604 ipv6 nd retrans-timer ipv6 nd retrans-timer This command is used to configure IPv6 RA (router advertisement) retrans > enable Switch # configure terminal Switch (config) # interface vlan1 Switch (config-if) # ipv6 nd retrans-timer 4294967295 Switch (config-if) # CLI Reference Guide 348 - D-Link DGS-6600-48TS | CLI Guide - Page 359
DGS-6604 ipv6 nd suppress-ra ipv6 nd suppress-ra This command is used to suppress IPv6 RA (router advertisement) on an interface to suppress IPv6 RA's: Switch > enable Switch # configure terminal Switch (config) # interface vlan1 Switch (config-if) # ipv6 nd suppress-ra CLI Reference Guide 349 - D-Link DGS-6600-48TS | CLI Guide - Page 360
DGS-6604 ipv6 neighbor ipv6 neighbor This command is used to add a static ipv6 neighbor entry. The no form of this command deletes entry: Switch > enable Switch # configure terminal Switch (config) # ipv6 neighbor fe80::1 vlan1 00-01-80-11-22-99 Switch (config) # CLI Reference Guide 350 - D-Link DGS-6600-48TS | CLI Guide - Page 361
Mode Usage Guideline Example Cost: Unconfigured INSTANCE-ID: 0 Interface configuration To modify the cost from the default value, set the metric manually using the ipv6 ospf cost command. Using the bandwidth command changes the link cost as long as the ipv6 ospf cost command is not used. The - D-Link DGS-6600-48TS | CLI Guide - Page 362
DGS-6604 ipv6 ospf dead-interval ipv6 ospf dead-interval To set the time period used, during which hello packets are not detected, to 60 seconds. Switch > enable Switch # configure terminal Switch (config)# interface vlan1 Switch (config-if)# ipv6 ospf dead-interval 60 CLI Reference Guide 352 - D-Link DGS-6600-48TS | CLI Guide - Page 363
DGS-6604 ipv6 ospf hello-interval ipv6 ospf hello-interval To specify the interval between hello packets sent from an interface, use 15 seconds. Switch > enable Switch # configure terminal Switch (config)# interface vlan1 Switch (config-if)# ipv6 ospf hello-interval 15 CLI Reference Guide 353 - D-Link DGS-6600-48TS | CLI Guide - Page 364
DGS-6604 ipv6 ospf priority ipv6 ospf priority To set the router priority, which helps determine the designated router for this priority value to 4. Switch > enable Switch # configure terminal Switch (config)# interface vlan1 Switch (config-if)# ipv6 ospf priority 4 CLI Reference Guide 354 - D-Link DGS-6600-48TS | CLI Guide - Page 365
DGS-6604 ipv6 ospf retransmit-interval ipv6 ospf retransmit-interval This command specifies the time between link-state advertisement (LSA) retransmissions for adjacencies belonging to an (config) # interface vlan1 Switch (config-if)# ipv6 ospf retransmit-interval 6 CLI Reference Guide 355 - D-Link DGS-6600-48TS | CLI Guide - Page 366
DGS-6604 ipv6 ospf shutdown ipv6 ospf shutdown To initiate an IPv6 OSPF protocol graceful shutdown at the interface level, use (VLAN 1): Switch > enable Switch # configure terminal Switch (config) # router ipv6 ospf Switch (config-router)# ipv6 ospf shutdown vlan1 CLI Reference Guide 356 - D-Link DGS-6600-48TS | CLI Guide - Page 367
not be considered. This setting has more significance on very low-speed links. The following example sets the transmit delay value to 3 seconds. Switch > enable Switch # configure terminal Switch (config) # interface vlan1 Switch (config-if)# ipv6 ospf transmit-delay 3 CLI Reference Guide 357 - D-Link DGS-6600-48TS | CLI Guide - Page 368
DGS-6604 ipv6 rip metric-offset ipv6 rip metric-offset To set the IPv6 RIP metric for an interface, use the ipv6 rip metric the RIP routing process. Switch > enable Switch # configure terminal Switch (config)# interface vlan1 Switch (config-if)# ipv6 rip metric-offset 10 CLI Reference Guide 358 - D-Link DGS-6600-48TS | CLI Guide - Page 369
DGS-6604 ipv6 rip split-horizon ipv6 rip split-horizon To enable IPv6 RIP split-horizon mechanism, use the ipv6 rip split-horizon RIP routing process. Switch > enable Switch # configure terminal Switch (config)# interface vlan1 Switch (config-if)# ipv6 rip split-horizon CLI Reference Guide 359 - D-Link DGS-6600-48TS | CLI Guide - Page 370
DGS-6604 ipv6 rip split-horizon poisoned ipv6 rip split-horizon poisoned To configure the poison reverse processing of IPv6 RIP process. Switch > enable Switch # configure terminal Switch (config)# interface vlan1 Switch (config-if)# ipv6 rip split-horizon poisoned CLI Reference Guide 360 - D-Link DGS-6600-48TS | CLI Guide - Page 371
DGS-6604 ipv6 ospf mtu-ignore ipv6 ospf mtu-ignore To disable IPv6 Open Shortest Path First (OSPF) maximum transmission unit (MTU receiving DBD packets.. Switch > enable Switch # configure terminal Switch (config)# interface vlan1 Switch (config-if)# ipv6 ospf mtu-ignore CLI Reference Guide 361 - D-Link DGS-6600-48TS | CLI Guide - Page 372
DGS-6604 ipv6 route ipv6 route Use ipv6 . A link-local address should be specified as the next hop for broadcast interfaces. Interface number. For more information about the numbering syntax for supported interface types, use the delete the default route of the system. CLI Reference Guide 362 - D-Link DGS-6600-48TS | CLI Guide - Page 373
DGS-6604 Practical Usage Examples ipv6 route Operators may prefer to specify a default path for the managed devices. By specifying a default gateway, mode. To remove a previously configured static route, use the no form of this command. No static routes are configured. CLI Reference Guide 363 - D-Link DGS-6600-48TS | CLI Guide - Page 374
DGS-6604 Practical Usage Examples ipv6 route Operators may prefer to specify the forwarding path of certain traffic. By doing this, the server resides. Switch > enable Switch # configure terminal Switch (config) # ipv6 route 2001:0DB8::/32 vlan 1 fe80::0200:00ff:fe00:a0a0 CLI Reference Guide 364 - D-Link DGS-6600-48TS | CLI Guide - Page 375
DGS-6604 ipv6 route Then we can use the show command to check whether the configured static route works or not. Switch > enable Switch mode. To remove a previously configured floating static route, use the no form of this command. No floating static routes are configured. CLI Reference Guide 365 - D-Link DGS-6600-48TS | CLI Guide - Page 376
DGS-6604 Practical Usage ipv6 route Operators may like to specify the priorities of multiple routes destined for the same network. When multiple fe80::0200:00ff:fe00:a0a0 distance 11 Switch (config) # ipv6 route 2001:0DB8::/32 vlan 2 fe80::0200:00ff:fe00:b0b0 distance 22 CLI Reference Guide 366 - D-Link DGS-6600-48TS | CLI Guide - Page 377
DGS-6604 ipv6 route This example shows how to delete entry cannot be set to the H/W routing table. Use the "ip6-route-longprefix enable" to support an IPv6 route with a prefix longer than 64 bits to configure an ACL table. After CMD enable long prefix. Switch (config) # CLI Reference Guide 367 - D-Link DGS-6600-48TS | CLI Guide - Page 378
DGS-6604 ipv6 router ospf area ipv6 router ospf area To enable IPv6 OSPF on an interface, use the ipv6 router ospf area an interface. Switch > enable Switch # configure terminal Switch (config)# interface vlan1 Switch (config-if)# ipv6 router ospf area 0 instance-id 2 CLI Reference Guide 368 - D-Link DGS-6600-48TS | CLI Guide - Page 379
DGS-6604 ipv6 router rip ipv6 router rip To enable the IPv6 RIP routing process on an interface, use the ipv6 router rip RIP routing process on VLAN 1. Switch > enable Switch # configure terminal Switch (config)# interface vlan1 Switch (config-if)# ipv6 router rip CLI Reference Guide 369 - D-Link DGS-6600-48TS | CLI Guide - Page 380
DGS-6604 ipv6 route long prefix log enable ipv6 route long prefix log enable This command is used to record syslog functions ip6-route-longprefix log enable command: Switch > enable Switch # configure terminal Switch (config) # no ipv6 unicast-routing long-prefix log CLI Reference Guide 370 - D-Link DGS-6600-48TS | CLI Guide - Page 381
DGS-6604 ipv6 unicast-routing long-prefix ipv6 unicast-routing long-prefix This command is used to enable supporting IPv6 routes with a prefix longer than 64bits to configure the ACL table. Switch # configure terminal Switch (config) # no ipv6 unicast-routing long-prefix CLI Reference Guide 371 - D-Link DGS-6600-48TS | CLI Guide - Page 382
DGS-6604 ipv6 unicast-routing long-prefix The following is a sample for an error message output from an > enable Switch # configure terminal Switch (config) # ipv6 unicast-routing long-prefix There is no enough ACL resource to support IPv6 route with long prefix. Switch (config) # CLI Reference - D-Link DGS-6600-48TS | CLI Guide - Page 383
DGS-6604 m keK y key KEY-ID key Use the key command to identify a key on a key chain used for routing protocol authentication. Use the no key router's keys, the first valid key will be chosen. To remove all keys, remove the key chain with the no key chain command. CLI Reference Guide 373 - D-Link DGS-6600-48TS | CLI Guide - Page 384
DGS-6604 m Example key The following example configures a key chain named chain1. Key1 named "forkey1string" will be accepted from 1:30 p.m. to 3:30 p.m. and 2009 duration 3600 Switch(config-keychain-key)# exit To verify the settings, enter the show ip key-chain command. CLI Reference Guide 374 - D-Link DGS-6600-48TS | CLI Guide - Page 385
DGS-6604 m key chain key chain To manage authentication keys, define a key chain, identify the keys that belong to the key chain, and specify , a key chain with named keys must first be created. It is recommended that only one key chain be configured per interface. CLI Reference Guide 375 - D-Link DGS-6600-48TS | CLI Guide - Page 386
DGS-6604 m Example key chain The following example configures a key chain named chain1. Key1 named "forkey1string" will be accepted from 1:30 p.m. to 3:30 p.m. 25 2009 duration 3600 Switch(config-keychain-key)# end To verify the settings, use the show ip key-chain command. CLI Reference Guide 376 - D-Link DGS-6600-48TS | CLI Guide - Page 387
DGS-6604 m key-string key-string Use the key-string command to specify the authentication string for a key. Use the no key-string chain key configuration Routing Information Protocol (RIP) Version 2 uses key chains for authentication. Each key can have only one key string. CLI Reference Guide 377 - D-Link DGS-6600-48TS | CLI Guide - Page 388
DGS-6604 m Example key-string The following example configures a key chain named chain1. Key1 named forkey1string will be accepted from 1:30 p.m. to 3:30 25 2009 duration 3600 Switch(config-keychain-key)# end Verify the settings by entering the show ip key-chain command. CLI Reference Guide 378 - D-Link DGS-6600-48TS | CLI Guide - Page 389
DGS-6604 m lacp port-priority laLcp port-priority Use the lacp port-priority command to configure the port priority. Use the no (config)# interface range eth3.4-3.5 Switch(config-if)# lacp port-priority 20000 Verify the settings with the show channel-group command. CLI Reference Guide 379 - D-Link DGS-6600-48TS | CLI Guide - Page 390
DGS-6604 m lacp system-priority lacp system- mode. The LACP system priority determines which switch controls the port priority for the aggregated link. The port priorities of the other switch are ignored. In a system priority comparison, the show channel-group command CLI Reference Guide 380 - D-Link DGS-6600-48TS | CLI Guide - Page 391
DGS-6604 m lease lease Use this command to configure the lease duration of an IP address that is assigned from a DHCP server to a client lease, in address pool "pool1", to 1 hour. switch# configure terminal switch(config)# ip dhcp pool pool1 switch(config-dhcp)# lease 0 1 CLI Reference Guide 381 - D-Link DGS-6600-48TS | CLI Guide - Page 392
DGS-6604 m lldp dot1-tlv-select lldp dot1-tlv-select To specify which optional type-length-value settings (TLVs) in the IEEE 802.1 Organizationally Specific no VLAN-ID is specified, all configured VLANS for VLAN NAME TLV will be cleared and no VLAN Name TLV will be sent. CLI Reference Guide 382 - D-Link DGS-6600-48TS | CLI Guide - Page 393
DGS-6604 m lldp dot1-tlv-select Syntax Description to the operation of the network. Such as Spanning Tree Protocol, the Link Aggregation Control Protocol, and numerous vendor proprietary variations are responsible for maintaining the advertised VLAN includes 1 to 3. CLI Reference Guide 383 - D-Link DGS-6600-48TS | CLI Guide - Page 394
DGS-6604 m lldp dot1-tlv-select Switch(config-if)# lldp dot1-tlv-select protocol-vlan 1-3 The following example disabling Port And Protocol shows how to disable LACP Protocol Identify TLV advertisement: Switch(config-if)# no lldp dot1-tlv-select protocol-identity lacp CLI Reference Guide 384 - D-Link DGS-6600-48TS | CLI Guide - Page 395
DGS cfg | link-aggregation | power | max-frame-size] no lldp dot3-tlv-select [mac-phy-cfg | link-aggregation | link for connected non-powered systems. The Power Via MDI TLV allows network management to advertise and discover the MDI power support , all supported IEEE 802.3 Organizationally Specific TLVs are - D-Link DGS-6600-48TS | CLI Guide - Page 396
DGS-6604 m Default Command Mode Usage Guideline lldp dot3-tlv-select No IEEE 802.3 Organizationally Specific TLV is selected. Interface configuration. The how to disable advertising MAC/PHY Configuration/Status TLV: Switch (config-if) # no lldp dot3-tlv-select mac-phy-cfg CLI Reference Guide 386 - D-Link DGS-6600-48TS | CLI Guide - Page 397
DGS-6604 m lldp fast-count lldp fast-count To set the LLDP-MED fast start repeat count on the switch, use the lldp fastcount command. Use one complete fast start interval. This example shows how to set LLDP MED fast start repeat count: Switch(config)# lldp fast-count 10 CLI Reference Guide 387 - D-Link DGS-6600-48TS | CLI Guide - Page 398
DGS-6604 m lldp hold-multiplier lldp hold-multiplier To set the hold multiplier for LLDP updates on the switch, use the lldp lldp hold-multiplier 3 This example shows how to set LLDP hold-multiplier to default value. Switch(config)# no lldp hold-multiplier CLI Reference Guide 388 - D-Link DGS-6600-48TS | CLI Guide - Page 399
DGS-6604 m lldp management-address lldp management-address To configure management address which will be advertised on the physical interface, use lldp management-address 10.1.1.1 This example shows how to enable eth3.3 and eth3.4 for set management address entry (ipv6) CLI Reference Guide 389 - D-Link DGS-6600-48TS | CLI Guide - Page 400
DGS-6604 m lldp management-address Switch(config)# interface range eth3.3-3.4 Switch(config-if-range)# lldp management-address FE80::250:A2FF:FEBF: Address TLV will be sent on eth3.5. Switch(config)# interface eth3.5 Switch(config-if-range)# no lldp management-address CLI Reference Guide 390 - D-Link DGS-6600-48TS | CLI Guide - Page 401
DGS-6604 m lldp med-tlv-select lldH p med ' if local device is PSE device or PD device. When no optional keyword is selected, all supported optional LLDP-MED TLVs are selected or de-selected in no form of this command. Default Command until it only receives LLDP packets. CLI Reference Guide 391 - D-Link DGS-6600-48TS | CLI Guide - Page 402
DGS-6604 m Example This example shows how to enable all TLVs: lldp med-tlv-select Switch(config-if)# lldp med-tlv-select This This example shows how to enable transmitting LLDP MED Inventory Management TLV: Switch(config-if)# lldp med-tlv-select inventory-management CLI Reference Guide 392 - D-Link DGS-6600-48TS | CLI Guide - Page 403
DGS-6604 m lldp receive lldp receive To enable a This command has no arguments or keywords. Default LLDP is enabled on all supported interfaces. Command Mode Interface Configuration mode Usage Guideline This command is used to . Switch(config-if)# no lldp receive CLI Reference Guide 393 - D-Link DGS-6600-48TS | CLI Guide - Page 404
DGS-6604 m lldp reinit lldp reinit To set the minimum time of re-initialization delay interval on the switch, use the lldp reinit command. (config)# lldp reinit 5 This example shows how to set the re-init delay interval to default value. Switch(config)# no lldp reinit CLI Reference Guide 394 - D-Link DGS-6600-48TS | CLI Guide - Page 405
DGS-6604 m lldI p run lldp run no lldp run Syntax Default Command Mode Usage Guideline Example lldp run To enable Link Layer Discovery Protocol (LLDP) globally, use the lldp run command in global configuration shows how to globally disable LLDP. Switch(config)# no lldp run CLI Reference Guide 395 - D-Link DGS-6600-48TS | CLI Guide - Page 406
DGS-6604 fully qualified domain name. When no optional keyword is selected, all supported optional 802.1AB basic management TLVs are selected or deselected in the sent to other devices. This example shows how to enable all supported optional 802.1AB basic management TLVs: Switch(config-if)# lldp - D-Link DGS-6600-48TS | CLI Guide - Page 407
DGS-6604 m Switch(config-if)# no lldp tlv-select system-name lldp tlv-select CLI Reference Guide 397 - D-Link DGS-6600-48TS | CLI Guide - Page 408
DGS-6604 m lldp transmit lldp transmit To enable the This command has no arguments or keywords. LLDP transmit is enabled on all supported interfaces. Interface Configuration mode This command is used to enable LLDP transmission on Switch(config-if)# no lldp transmit CLI Reference Guide 398 - D-Link DGS-6600-48TS | CLI Guide - Page 409
DGS-6604 m lldp tx-delay lldp tx-delay To set the transmission delay timer use the lldp tx-delay command. This delay timer Switch(config)# lldp tx-delay 8 The following example configures the transmission delay timer to default value. Switch(config)# no lldp tx-delay CLI Reference Guide 399 - D-Link DGS-6600-48TS | CLI Guide - Page 410
DGS-6604 m lldp tx-interval lldp tx-interval To set the LLDPDUs transmission interval on the switch, use the lldp tx-interval command. Use lldp tx-interval 50 This example shows how to set LLDP transmission interval to default value: Switch(config)# no lldp tx-interval CLI Reference Guide 400 - D-Link DGS-6600-48TS | CLI Guide - Page 411
DGS-6604 m logging file logging file Syntax Default Command Mode Usage Guideline Example logging file Use the logging file command to enable The example below sets log messages to be saved to flash. Switch> enable Switch# configure terminal Switch(config)# logging file CLI Reference Guide 401 - D-Link DGS-6600-48TS | CLI Guide - Page 412
DGS-6604 m logging host logging host Use the address of the host to be used as the syslog server. IPv4 and IPv6 address are supported. port UDP-PORT (Optional) The UDP port number to be used for the syslog server. IP-ADDRESS: None UDP port: 514. severity: informational CLI Reference Guide 402 - D-Link DGS-6600-48TS | CLI Guide - Page 413
DGS-6604 m Command Mode Usage Guideline Example facility: local7 logging host Global configuration The number of supporting SYSLOG servers is project dependent. When the number of configured SYSLOG servers critical Verify the settings with the show logging host command. CLI Reference Guide 403 - D-Link DGS-6600-48TS | CLI Guide - Page 414
DGS-6604 m logging level logging level Use this command to limit messages logged to the message buffer based on severity level. switch> enable switch# configure terminal Switch(config)# logging level all 1 Verify the settings by entering the show logging command. CLI Reference Guide 404 - D-Link DGS-6600-48TS | CLI Guide - Page 415
DGS-6604 m logging on logging on logging on Use the logging on command to start logging system messages on this switch. Use the the below commands. Switch> enable switch# configure terminal Switch(config)# logging on Verify the settings with the show logging command. CLI Reference Guide 405 - D-Link DGS-6600-48TS | CLI Guide - Page 416
DGS-6604 m login login Syntax Default Command Mode Usage Guideline Example login Use this to login with username user1. Switch>login User Access Verification Username: user1 Password: DGS-6604 Chassis-based High-Speed Switch Command Line Interface Switch# Firmware: 2.01.001 Copyright (c) 2011 - D-Link DGS-6600-48TS | CLI Guide - Page 417
DGS-6604 m logout logout Syntax Default Command Mode Usage Guideline Example logout Use this command to close an active terminal session by logging off the device using the logout command. This example shows how to logout from the switch. Switch# disable Switch> logout CLI Reference Guide 407 - D-Link DGS-6600-48TS | CLI Guide - Page 418
DGS-6604 m loopback-detection (interface) loopback-detection errdisable recovery cause loopback-detection" global configuration command. Alternatively, the user can manually re-enable the port by entering the "shutdown" then "no shutdown" command detection Switch(config-if)# CLI Reference Guide 408 - D-Link DGS-6600-48TS | CLI Guide - Page 419
DGS-6604 m loopback-detection (interface) You can verify your settings by entering the show loopback-detection command. CLI Reference Guide 409 - D-Link DGS-6600-48TS | CLI Guide - Page 420
DGS-6604 m loopback-detection (global) loopback-detection errdisable recovery cause loopback-detection" global configuration command. Alternatively, the user can manually re-enable the port by entering the "shutdown" then "no shutdown" show loopback-detection command. CLI Reference Guide 410 - D-Link DGS-6600-48TS | CLI Guide - Page 421
DGS-6604 m loopback-detection mode loopback-detection mode Use the command to decide the loopback detection mode. To return to the default )# loopback-detection mode vlan-based Switch(config)# You can verify your settings by entering the show loopback-detection command. CLI Reference Guide 411 - D-Link DGS-6600-48TS | CLI Guide - Page 422
DGS-6604 m loopback-detection interval-time loopback-detection interval-time Use the command to configure timer interval. Use no command to loopback-detection interval-time 20 Switch(config)# You can verify your settings by entering the show loopback-detection command. CLI Reference Guide 412 - D-Link DGS-6600-48TS | CLI Guide - Page 423
DGS-6604 m mac access-group mMac access-group Use the mac access-group command to specify a MAC access list to be applied to an Switch(config)# interface eth3.1 Switch(config-if)# mac access-group daily-profile in Verify the settings with the show access-group command. CLI Reference Guide 413 - D-Link DGS-6600-48TS | CLI Guide - Page 424
DGS-6604 m mac access-list mac access-list Use the mac access-list command to create a MAC access list in the configuration. Enter -list extended daily-profile Switch(config-mac-ext-acl)# Verify the access list configuration settings with the show access-list command. CLI Reference Guide 414 - D-Link DGS-6600-48TS | CLI Guide - Page 425
DGS-6604 m mac address-table aging destination-hit mac address-table aging destination-hit Use the MAC address-table aging destination-hit )# mac address-table aging destination-hit Verify the setting by entering the show mac address-table aging destinationhit command. CLI Reference Guide 415 - D-Link DGS-6600-48TS | CLI Guide - Page 426
DGS-6604 m mac address-table aging-time mac address-table aging-time Use this command to set the length of time that a dynamic entry seconds: Switch(config)# mac address-table aging-time 200 Verify the setting by entering the show mac address-table aging-time command. CLI Reference Guide 416 - D-Link DGS-6600-48TS | CLI Guide - Page 427
DGS-6604 m mac address-table static mac address-table static Use the mac address-table static command to add a static address to the MAC address -table static C2:F3:22:0A:12:F4 vlan 4 interface eth3.1 Verify the setting by entering the show mac address-table command. CLI Reference Guide 417 - D-Link DGS-6600-48TS | CLI Guide - Page 428
DGS-6604 m mac-base ( VLAN ) mac-base ( VLAN ) Use the mac-base command to create a MAC-based VLAN ID assignment entry. Use the no form of Switch(config-vlan)#mac-base 00-80-cc-00-00-11 Switch(config-vlan)#exit Verify the settings with the show vlan command. CLI Reference Guide 418 - D-Link DGS-6600-48TS | CLI Guide - Page 429
DGS classified for any QoS service. cos COS-LIST Specific services code point values. Enter one or more differentiated service of protocols supported by most routers of Quality of Service (QoS) basis of a Layer 2 class of service (CoS) marking, use the match differentiated service code point ( - D-Link DGS-6600-48TS | CLI Guide - Page 430
DGS-6604 m Supported Protocols: Protocol arp bgp dhcp dns egp ftp ip netbios nfs ntp ospf pppoe rip rtsp CLI Reference Guide match value from a class map, the class. The following table lists the reference for the supported protocols. Description IP Address Resolution Protocol (ARP) Border Gateway - D-Link DGS-6600-48TS | CLI Guide - Page 431
DGS-6604 m Protocol ssh telnet tftp Description Secured shell Telnet Trivial File Transfer Protocol match Examples The following example specifies a class (config)# class-map class-home-user Switch(config-cmap)# match access-list acl-home-user Switch(config-cmap)# exit CLI Reference Guide 421 - D-Link DGS-6600-48TS | CLI Guide - Page 432
DGS-6604 m match In the following example rate policer and a two rate policer for class voice and video-n-data respectively). The service policy configured in this example is attached to Ethernet interface eth3.1. Switch(config)# class-map the show class-map command. CLI Reference Guide 422 - D-Link DGS-6600-48TS | CLI Guide - Page 433
DGS-6604 m match as-path match as-path Use this command to match a BGP autonomous system path access list. To delete an entry, use (config)# route-map myPolicy permit 1 Switch(config-route-map)# match as-path PATH_ACL Verify the settings with the show route-map command. CLI Reference Guide 423 - D-Link DGS-6600-48TS | CLI Guide - Page 434
DGS-6604 m match community match community Use the match community command to match a Border Gateway Protocol (BGP) community. Use the no match community ALPHA-COMMUNITY exact Switch(config-route-map)# set weight 100 Verify the settings with the show route-map command CLI Reference Guide 424 - D-Link DGS-6600-48TS | CLI Guide - Page 435
DGS-6604 m match ip address match ip address Use this command to define a clause to match the route based on IP standard access list. myPolicy permit 1 Switch(config-route-map)# match ip address myacl You can verify your settings by entering the show route map command. CLI Reference Guide 425 - D-Link DGS-6600-48TS | CLI Guide - Page 436
DGS-6604 m match ipv6 address match ipv6 address Use this command to define a clause to match the route based on IPv6 access list. match permit 1 Switch(config-route-map)# match ipv6 address aclv6cfg You can verify your settings by entering the show route map command. CLI Reference Guide 426 - D-Link DGS-6600-48TS | CLI Guide - Page 437
DGS-6604 m maximum-paths maximum-paths To control the maximum number of parallel routes that an IP routing protocol can support, use the maximum-paths command in router configuration mode. maximum-paths 8 Verify the settings by entering the show ip route summary command. CLI Reference Guide 427 - D-Link DGS-6600-48TS | CLI Guide - Page 438
DGS-6604 m max-rcv-frame-size max-rcv-frame-size Use the command to set the maximum Ethernet frame size allowed. Use the default form eth4.1 Switch(config-if)# default max-rcv-frame-size Switch(config-if)# end Verify the settings by entering the show interface command. CLI Reference Guide 428 - D-Link DGS-6600-48TS | CLI Guide - Page 439
DGS-6604 m media-type media-type Use send or wait for signals to negotiate clock. The copper medium will be selected even if the link state is down. This example shows how configure the interface eth3.1 medium to fiber. Switch(config entering the show interface command. CLI Reference Guide 429 - D-Link DGS-6600-48TS | CLI Guide - Page 440
DGS-6604 m mgmt-if mgmt-if Syntax Default Command Mode Usage Guideline Example mgmt-if Use this command to enter into the management interface enter the management interface mode. Switch(config)# mgmt-if Switch(mgmt-if)# Verify the settings using the show mgmt-if command. CLI Reference Guide 430 - D-Link DGS-6600-48TS | CLI Guide - Page 441
DGS-6604 m monitor session monitor session Use monitor session to create a port mirroring session, allowing source ports as mirrored ports to another session simultaneously. • For a destination port, all the layer 2 settings configured for this port are all ineffective. CLI Reference Guide 431 - D-Link DGS-6600-48TS | CLI Guide - Page 442
DGS-6604 m Examples monitor session • IEEE 802.1x authentication on a port cannot be enabled for a destination port, but is allowed on the monitor session 1 source interface eth3.2,eth3.4 Switch(config)# end Verify the settings by entering the show monitor session command. CLI Reference Guide 432 - D-Link DGS-6600-48TS | CLI Guide - Page 443
DGS-6604 m monitor session destination remote vlan monitor session destination remote vlan Use the command to configure the RSPAN VLAN and destination VLAN with destination interface eth3.6 and three source ports (eth 2.2, eth 2.3 and eth 2.4) as the port being monitored: CLI Reference Guide 433 - D-Link DGS-6600-48TS | CLI Guide - Page 444
DGS-6604 m Switch# configure terminal Switch(config)# vlan 100 Switch(config-vlan)# remote-span Switch(config-vlan)#exit Switch(config)# monitor remote vlan 100 interface eth3.6 Switch(config)# You can verify your settings by entering the show monitor session command. CLI Reference Guide 434 - D-Link DGS-6600-48TS | CLI Guide - Page 445
DGS-6604 m monitor session source interface monitor session source interface Use monitor session source interface to configure the source port physical port 2.1 as a destination port and three source physical ports (eth 2.2, eth 2.3 and eth 2.4) as monitor source ports. CLI Reference Guide 435 - D-Link DGS-6600-48TS | CLI Guide - Page 446
DGS-6604 m monitor session source interface Switch# configure terminal Switch(config)# monitor session 1 destination interface eth2.1 Switch(config)# monitor session eth2.2,eth2.4 Switch(config)# You can verify your settings by entering the show monitor session command. CLI Reference Guide 436 - D-Link DGS-6600-48TS | CLI Guide - Page 447
DGS-6604 m monitor session source remote vlan monitor session source remote vlan Use the command to configure the RSPAN VLAN for a RSPAN destination session 100 as the RSPAN VLAN. The monitored packets arrive at port eth2.1 and will be transmitted out from port eth1.4. CLI Reference Guide 437 - D-Link DGS-6600-48TS | CLI Guide - Page 448
DGS-6604 m monitor session source remote vlan Switch# configure terminal Switch(config)# vlan 100 Switch(config-vlan)# remote-span Switch Switch(config)# monitor session 2 source remote vlan 100 Switch(config)# monitor session 2 destination interface eth2.4 Switch(config)# CLI Reference Guide 438 - D-Link DGS-6600-48TS | CLI Guide - Page 449
DGS-6604 m mtu mtu BYTES default mtu mtu for further processing and the check is done in egress ports. This is especially important to support IPv6 because an IPv6 router should send out ICMP messages to source device for an MTU by entering the show interface command CLI Reference Guide 439 - D-Link DGS-6600-48TS | CLI Guide - Page 450
DGS-6604 m multicast filtering-mode multicast filtering-mode Mode Usage Guideline Example forward-unregistered Interface configuration Only VLAN interfaces support this command. This example shows how to set the multicast filtering the show multicast filtering-mode command. CLI Reference Guide 440 - D-Link DGS-6600-48TS | CLI Guide - Page 451
DGS-6604 m naN me name NAME no name name Use the name command to set the name of an MST region. To return to the Switch(config)#spanning-tree mst configuration Switch(config-mst)# name alpha Verify the settings by entering the show spanning-tree mst configuration command. CLI Reference Guide 441 - D-Link DGS-6600-48TS | CLI Guide - Page 452
DGS-6604 m neighbor neighbor Use the neighbor command to define a neighboring router with which to exchange routing information. Use the no form to vlan1 Switch(config-router)# neighbor 10.50.71.50 Verify the settings by entering the show ip protocols rip command CLI Reference Guide 442 - D-Link DGS-6600-48TS | CLI Guide - Page 453
DGS-6604 m neighbor (RIP IPv6) neighbor (RIP IPv6) To IPv6-ADDRESS IFNAME no neighbor IPv6-ADDRESS IFNAME Syntax Description IPv6-ADDRESS IPv6 link-local address of a router with which routing information will be exchanged. IFNAME the show ipv6 rip database command CLI Reference Guide 443 - D-Link DGS-6600-48TS | CLI Guide - Page 454
DGS-6604 m neighbor advertisement-interval neighbor advertisement-interval Use this command to set the minimum interval between each transmission of Border -af)# neighbor 10.4.4.4 advertisement-interval 15 Verify the settings by entering the show ip bgp neighbor command. CLI Reference Guide 444 - D-Link DGS-6600-48TS | CLI Guide - Page 455
DGS-6604 m neighbor description neighbor description Use this command to associate a text description with a neighbor. Use the no form of the command to )# neighbor 172.16.10.10 description ABC in China Verify the settings by entering the show ip bgp neighbor command. CLI Reference Guide 445 - D-Link DGS-6600-48TS | CLI Guide - Page 456
DGS-6604 m neighbor filter-list neighbor filter-list Use this command to create a BGP filter. Use the no form of the command to disable this neighbor 172.16.1.1 filter-list myacl out Verify the settings, in User Exec Mode, by entering the show ip protocols bgp command. CLI Reference Guide 446 - D-Link DGS-6600-48TS | CLI Guide - Page 457
DGS-6604 m neighbor peer-group (create group) neighbor peer-group (create group) Use this command to create a peer group. Use the no form how to create a peer group named ALPHA-GROUP Switch(config)# router bgp 65100 Switch(config-router)# neighbor ALPHA-GROUP peer-group CLI Reference Guide 447 - D-Link DGS-6600-48TS | CLI Guide - Page 458
DGS-6604 m neighbor peer-group (add group member) neighbor peer-group (add group member) Use this command to add a neighbor into a peer group. Use 10.1.1.254 peer-group ALPHA-GROUP Verify the settings by entering the show ip bgp neighbor command in User EXEC mode. CLI Reference Guide 448 - D-Link DGS-6600-48TS | CLI Guide - Page 459
DGS-6604 m neighbor remote-as neighbor remote-as Use this command to add an entry to the Border Gateway Protocol (BGP) neighbor table. Use 10.108.0.0 Switch(config-router)# neighbor 10.108.2.1 remote-as 110 Verify the settings by entering the show ip bgp neighbor command. CLI Reference Guide 449 - D-Link DGS-6600-48TS | CLI Guide - Page 460
DGS-6604 m neighbor route-map neighbor route-map Use this command to apply a route map to incoming or outgoing routes. Use the no form )#set origin incomplete Swtich(config-route-map)#end Switch(config)# Verify the settings by entering the show ip bgp neighbor command. CLI Reference Guide 450 - D-Link DGS-6600-48TS | CLI Guide - Page 461
DGS-6604 m neighbor send-community neighbor send-community Use this command to specify that the communities attribute should be sent to a BGP Switch(config-router-af)# neighbor 10.4.4.4 send-community both Verify the settings by entering the show ip bgp neighbor command. CLI Reference Guide 451 - D-Link DGS-6600-48TS | CLI Guide - Page 462
DGS-6604 m neighbor shutdown neighbor shutdown Use this command to disable a neighbor or peer group. Use the no form of this command to re-enable 65100 Switch(config-router)# neighbor 172.16.10.10 shutdown Verify the settings by entering the show ip bgp neighbor command. CLI Reference Guide 452 - D-Link DGS-6600-48TS | CLI Guide - Page 463
DGS-6604 m neighbor timers neighbor timers Use this command to set the timers for a specific BGP peer or peer group. Use the no form of this 65100 Switch(config-router)# neighbor 172.16.10.10 timer 120 360 Verify the settings by entering the show ip bgp neighbor command. CLI Reference Guide 453 - D-Link DGS-6600-48TS | CLI Guide - Page 464
DGS-6604 m neighbor update-source neighbor update-source Use this command to allow internal BGP sessions to use any operational interface for TCP -router)# neighbor 172.16.10.10 update-source vlan1 Verify the settings by entering the show ip bgp neighbor command. CLI Reference Guide 454 - D-Link DGS-6600-48TS | CLI Guide - Page 465
DGS-6604 m neighbor weight neighbor weight Use this command to specify the weight associated with a specific neighbor. To remove a weight assignment, Switch(config-router-af)# neighbor 10.4.4.4 weight 10000 Verify the settings by entering the show ip bgp neighbor command. CLI Reference Guide 455 - D-Link DGS-6600-48TS | CLI Guide - Page 466
DGS-6604 m netbios node-type netbios node-type This command is used to system queries the name server first, and then broadcasts. Example Resolution through LMHOSTS and/or Domain Name Service (DNS), if enabled, will follow these methods. The following is sample of configuring the Netbios node - D-Link DGS-6600-48TS | CLI Guide - Page 467
DGS-6604 m netbios scope-id netbios scope-id This command configures the NetBIOS scope id for Microsoft Dynamic Host Configuration Protocol (DHCP) switch#configure terminal switch(config)#ip dhcp pool pool1 switch(config-dhcp)#netbios scope-id alpha switch(config-dhcp)# CLI Reference Guide 457 - D-Link DGS-6600-48TS | CLI Guide - Page 468
DGS-6604 m netbios wins-server netbios wins-server To configure the IP address of a WINS server for Microsoft Dynamic Host Configuration Protocol (DHCP) 10.1.1.100 so that 10.1.1.200 becomes the primary WINS server. switch(config-dhcp)#no netbios wins-server 10.1.1.100 CLI Reference Guide 458 - D-Link DGS-6600-48TS | CLI Guide - Page 469
DGS-6604 m network network Use the command to specify that the network utilizes Routing Information Protocol (RIP). To remove an RIP network entry, -router)# network 10.99.0.0/16 Switch(config-router)# end Verify the settings by entering the show ip protocols rip command. CLI Reference Guide 459 - D-Link DGS-6600-48TS | CLI Guide - Page 470
DGS-6604 m network (BGP) network (BGP) Use this command to configure the networks to be advertised by the Border Gateway Protocol (BGP) protocol. To in the BGP updates for the AS number of 65100 Switch(config)# router bgp 65100 Switch(config-router)# network 10.108.0.0 CLI Reference Guide 460 - D-Link DGS-6600-48TS | CLI Guide - Page 471
DGS-6604 m network area network area Use this command to enable OSPF routing with a specified Area ID. It enables this routing on terminal Switch(config)# router ospf Switch(config-router)# network 10.0.0.0/8 area 3 Verify the settings with the show ip ospf command. CLI Reference Guide 461 - D-Link DGS-6600-48TS | CLI Guide - Page 472
DGS-6604 m next-server next-server Configure the next server in a DHCP client's boot process. Use the no form of this command to boot process in pool named "pool1" switch# configure terminal switch(config)# ip dhcp pool pool1 switch(config-dhcp)# next-server 10.1.1.1 CLI Reference Guide 462 - D-Link DGS-6600-48TS | CLI Guide - Page 473
DGS-6604 m passive-interface paP ssive-interface Use the passive-interface command to disable sending OSPF protocol packets on an interface. )# router ospf Switch(config-router)##passive-interface vlan1 Verify the settings by entering the show ip ospf interface command. CLI Reference Guide 463 - D-Link DGS-6600-48TS | CLI Guide - Page 474
DGS-6604 m passive-interface (IPv6 OSPF) passive-interface (IPv6 OSPF) To disable sending IPv6 OSPF protocol packets on an interface, use ipv6 ospf Switch (config-router)# passive-interface vlan1 Verify the settings by entering the show ipv6 ospf interface command. CLI Reference Guide 464 - D-Link DGS-6600-48TS | CLI Guide - Page 475
DGS-6604 m passive interface (RIP) passive interface (RIP) To disable sending routing updates on an interface, use the passive-interface command. interface vlan1 Switch(config-router)#exit Switch(config)# Verify the settings by entering the show ip rip interface command. CLI Reference Guide 465 - D-Link DGS-6600-48TS | CLI Guide - Page 476
DGS-6604 m passive-interface (RIP IPv6) passive-interface (RIP IPv6) To disable sending routing updates on an interface, use the passive-interface )# passive-interface vlan1 Switch(config-router)#exit Verify the settings by entering the show ipv6 rip interface command. CLI Reference Guide 466 - D-Link DGS-6600-48TS | CLI Guide - Page 477
DGS-6604 m password recovery password recovery To configure the security password local authentication in case fail to connect the remove AAA server. A series of prompt message will guide user to complete the Password Recovery procedure. User could answer "yes" to update the passwords or - D-Link DGS-6600-48TS | CLI Guide - Page 478
console type (y/n) [n]?y Switch(reset-config)# logout User Access Verification Username: alex Password: Chassis-based High-Speed Switch Command Line Interface Firmware: 2.01.001 Copyright (c) 2010 D-Link Corporation. All rights reserved. DGS-6600:15# CLI Reference Guide 468 - D-Link DGS-6600-48TS | CLI Guide - Page 479
DGS-6604 m password recovery This example shows the situation when user account is 15 123456 Total Entries: 4 Switch(reset-config)# Switch(reset-config)# password-recovery This command will guide you to do the password recovery procedure. Do you want to update the user account (y/n) [n]?y - D-Link DGS-6600-48TS | CLI Guide - Page 480
DGS-6604 m This example shows how to verify the configuration: password recovery Switch(reset-config)#show username Password : yes Http Session: Login authentication: Local Authentication: yes Enable authentication: Local Authentication: yes Switch(reset-config)# CLI Reference Guide 470 - D-Link DGS-6600-48TS | CLI Guide - Page 481
DGS-6604 m password encryption password encryption Use the password encryption command to enable encryption of the password defined by both: • the encryption. Switch(config)# password encrypt Verify the settings by entering the show system protocol-state command. CLI Reference Guide 471 - D-Link DGS-6600-48TS | CLI Guide - Page 482
DGS-6604 m periodic periodic Use the periodic command to specify the period of time to be covered in a time range profile. periodic {daily HH: time-range)#periodic monthly 1 19:00 to 2 17:00 Switch(config)#end Verify the settings by entering the show time-range command. CLI Reference Guide 472 - D-Link DGS-6600-48TS | CLI Guide - Page 483
DGS-6604 m permit | deny (ip access-list) permit | deny (ip access-list) Use can be filtered by precedence level, as specified by a number from 0 to 7. (Optional) Specifies the Differentiated Services Control pointer (DSCP) value, as specified by a number from 0 to 63. (Optional) Packets can be - D-Link DGS-6600-48TS | CLI Guide - Page 484
DGS-6604 m permit | deny (ip access-list) OPERATOR PORT (Optional) Compares source or destination port. OPERATOR can be lt (less than, match on a lower entries are: tcp packets destined to network 10.20.0.0/16, tcp packets destined to host 10.100.1.2 and all icmp packets. CLI Reference Guide 474 - D-Link DGS-6600-48TS | CLI Guide - Page 485
DGS-6604 m permit | deny (ip access-list) Switch(config)# ip access-list extended Strict-Control Switch(config-ip-ext-acl)# permit tcp any 10.20.0.0 ext-acl)# permit icmp any any Switch(config-ip-ext-acl)# exit Verify the settings by entering the show access-list command. CLI Reference Guide 475 - D-Link DGS-6600-48TS | CLI Guide - Page 486
DGS-6604 m permit | deny (ipv6 access list) permit | deny (ipv6 access list) Use the permit command to add an entry to the IPv6 access- acceptable range is from 1 to 65534 for lt operator (Optional) Specifies the name of time-period profile for activation the accesslist. CLI Reference Guide 476 - D-Link DGS-6600-48TS | CLI Guide - Page 487
DGS-6604 m Syntax Description PROFILE-NAME PRIORITY permit | deny (ipv6 access list) Used with the no form of the commands, this option, time-range ( -acl)#permit icmpv6 any any Switch(config-ipv6-ext-acl)# exit Verify the settings by entering the show access-list command. CLI Reference Guide 477 - D-Link DGS-6600-48TS | CLI Guide - Page 488
DGS-6604 m permit | deny (mac access-list) permit | deny (mac access-list) largest sequence in that access list and it is placed at the end of the list. If the priority is manually assigned, it is better to have a reserved interval for a future higher priority entry. Otherwise the system attempts - D-Link DGS-6600-48TS | CLI Guide - Page 489
DGS-6604 m Command Mode Usage Guideline Example permit | deny (mac access-list) MAC access-list extended configuration The time-range profile must be 00:00 any Switch(config-mac-ext-acl)# exit Switch(config)# Verify the settings by entering the show access-list command. CLI Reference Guide 479 - D-Link DGS-6600-48TS | CLI Guide - Page 490
DGS-6604 m ping ping Use ping to diagnose basic it will be ignored when it is along with -A option. -Q TOS Set Quality of Service on ICMP data grams. -s PACKETSIZE Specifies the number of data bytes to be sent. Default bytes -c: 5 count packets -i: 1 second -Q: 0 TOS CLI Reference Guide 480 - D-Link DGS-6600-48TS | CLI Guide - Page 491
DGS-6604 m Command Mode Usage Guideline Examples ping -w: 0 (Don't stop) -W: 1 second Management interface configuration or User EXEC The ping command sends an =5, received=5, packet loss=0 (0%) round trip times min/avg/max/mdev= 0.760/19.040/92.120/36.540 ms Switch# CLI Reference Guide 481 - D-Link DGS-6600-48TS | CLI Guide - Page 492
DGS-6604 m poe port priority poe port priority Use this command to configure the priority of power-sourcing for ports. Use the no the first priority. Switch(config)# interface eth3.1 Switch(config-if)#poe port priority 1st Switch(config-if)#end Switch(config)# Switch# CLI Reference Guide 482 - D-Link DGS-6600-48TS | CLI Guide - Page 493
DGS-6604 m poe port description poe port description Use the poe port description command to configure the PoE port specific description. Use to configure the PoE port description. Switch(config)# interface eth3.1 Switch(config-if)# poe port description For VOIP usage CLI Reference Guide 483 - D-Link DGS-6600-48TS | CLI Guide - Page 494
DGS-6604 m poe service-policy poe service-policy Use the command to configure power service policy for whole system's usage under power shortage condition. poe service service policy is used to determine the power service port can be serviced with power higher than all other serviced ports. In the - D-Link DGS-6600-48TS | CLI Guide - Page 495
DGS- detection. The power quantity which allowed to the port is configured by user manually. max MAX-WATTAGE (Optional) Limit the power allowed on the port. The . This command is supported only on PoE-capable ports. If you enter this command on a port that does not support PoE, an error Guide 485 - D-Link DGS-6600-48TS | CLI Guide - Page 496
DGS-6604 m of DGS-6600's PoE functionality. But we strongly recommend using 15.4W as the maximum power threshold in static mode. If PD only needs 15.4W )# poe power-inline auto time-range rd_time You can verify your settings by entering the poe power inline status command. CLI Reference Guide 486 - D-Link DGS-6600-48TS | CLI Guide - Page 497
DGS-6604 m police police To configure traffic policing using single rate, use the police command in policymap class configuration mode. To remove that exceed the rate limit. (Optional) Specifies action to take on packets that violate the normal and maximum burst sizes. CLI Reference Guide 487 - D-Link DGS-6600-48TS | CLI Guide - Page 498
DGS-6604 m police Syntax Description ACTION Action to take on packets. Specifies one of the following keywords: "drop-Drops the packet. "set-dscp-transmit value-Sets the IP differentiated services code point -pmap-c)#exit Switch(config-pmap)# exit Switch(config)# CLI Reference Guide 488 - D-Link DGS-6600-48TS | CLI Guide - Page 499
DGS-6604 m police Later it is realized that a two rate police should be applied to class-movie traffic and a two rate police (police cir command) is used when the violate-action option is specified in the police command. The conform bucket is initially full (the full size CLI Reference Guide 489 - D-Link DGS-6600-48TS | CLI Guide - Page 500
DGS-6604 m Example police is the number of bytes specified as the normal burst size). The exceed the match criteria for the traffic class in a policy map (using the policy-map command). The service-policy command is then used to attach this service policy to the interface. CLI Reference Guide 490 - D-Link DGS-6600-48TS | CLI Guide - Page 501
DGS-6604 m police In this particular example, traffic policing is configured with an average (config-pmap-c)# exit Switch(config-pmap)# exit Switch(config)# interface eth3.1 Switch(config-if)# service-policy police-setting Verify the settings by entering the show policy-map command. CLI Reference - D-Link DGS-6600-48TS | CLI Guide - Page 502
DGS-6604 m police aggregate police aggregate To configure a named aggregate policer as the policy for a traffic class in a policy map, use -pmap-c)# police aggregate agg_policer1 Switch(config-pmap-c)# exit Verify the settings by entering the show policy-map command. CLI Reference Guide 492 - D-Link DGS-6600-48TS | CLI Guide - Page 503
DGS-6604 m police cir police cir To configure traffic policing using two The actions can be drop - Packets will be dropped. set-dscp-transmit VALUE - Sets the IP differentiated services code point (DSCP) value and transmits the packet with the new IP DSCP value. Default transmit - Transmits - D-Link DGS-6600-48TS | CLI Guide - Page 504
DGS-6604 m Command Mode Usage Guideline violate-action: equals exceed-action police cir Policy map class configuration As a packet arrives at a port, the Tc token bucket is updated at the CIR value. The Tc token bucket can contain up to the confirm burst (Bc) value. CLI Reference Guide 494 - D-Link DGS-6600-48TS | CLI Guide - Page 505
DGS-6604 m police cir "The Tp token bucket is updated at the PIR value. The Tp token bucket can contain up to the peak burst (Be is marked as conforming to the specified rate, and both token buckets-Tc(t) and Tp(t)-are updated as follows: Tp(t) = Tp(t) - B Tc(t) = Tc(t) - B CLI Reference Guide 495 - D-Link DGS-6600-48TS | CLI Guide - Page 506
DGS-6604 m Example police cir Example In the following example, two-rate drop Switch(config-pmap-c)# exit Switch(config-pmap)# exit Switch(config)# interface eth3.1 Switch(config-if)# service-policy policy1 Switch(config-if)# end Switch# show policy-map policy1 Policy Map policy1 Class police police - D-Link DGS-6600-48TS | CLI Guide - Page 507
DGS-6604 m policy-map policy-map To enter policy-map configuration mode and create or modify a policy map that can be attached to one or more interfaces as a service policy, use the policy-map command in global configuration matches access control list (ACL) acl_rd. The CLI Reference Guide 497 - D-Link DGS-6600-48TS | CLI Guide - Page 508
DGS-6604 m policy-map second class is the default class, named class-default to which packets that do not satisfy the defined classes are included Switch(config-pmap-c)# set ip dscp 00 Switch(config-pmap-c)# exit Verify the settings by entering the show policy-map command CLI Reference Guide 498 - D-Link DGS-6600-48TS | CLI Guide - Page 509
DGS-6604 m port-channel load-balance port-channel load-balance Use port-channel load-balance to configure the load balance algorithm that the channel load-balance src-ip Switch(config)# end Verify the settings by entering the show channel-group load-balance EXEC command. CLI Reference Guide 499 - D-Link DGS-6600-48TS | CLI Guide - Page 510
DGS Saving" function on different hardware components. Currently, one component is supported: phy. Select the option "phy", it will set the , the chips automatically enter "low-power" mode if the signal from a copper link partner is lost. They will go to normal mode when a signal is detected Guide 500 - D-Link DGS-6600-48TS | CLI Guide - Page 511
DGS-6604 m pvid VLAN-ID pvid VLAN-ID Use the pvid interface configuration command to specify the native VLAN for the trunk or hybrid eth4.1 Switch(config-if)# hybrid vlan 1000 untagged Switch(config-if)# pvid 1000 Verify the settings by entering the show vlan command. CLI Reference Guide 501 - D-Link DGS-6600-48TS | CLI Guide - Page 512
DGS-6604 m qos aggregate-policer qoQ s aggregate-policer To define a named aggregate policer for use in policy maps, use the qos aggregate-policer command BURST min: 64KB max:32GB Specifies the burst size for the first token bucket in bytes. min:4KB max:16MB default:4KB. CLI Reference Guide 502 - D-Link DGS-6600-48TS | CLI Guide - Page 513
DGS-6604 m qos aggregate-policer Syntax Description PEAK- keywords: "drop-Drops the packet. "set-dscp-transmit VALUE - Sets the IP differentiated services code point (DSCP) value and transmits the packet with the new IP DSCP value. "transmit name are the same. CLI Reference Guide 503 - D-Link DGS-6600-48TS | CLI Guide - Page 514
DGS-6604 m Example qos aggregate-policer In the following example, an aggregate policer named agg-policer5 with single rate two colors is configured. This named aggregator policer is applied as the service policy settings by entering the show qos aggregate-policer command. CLI Reference Guide 504 - D-Link DGS-6600-48TS | CLI Guide - Page 515
DGS-6604 m qos bandwidth qos bandwidth To set the received bandwidth limit values for an interface, use the bandwidth ingress command in interface 128 Switch(config-if)#qos bandwidth egress 256 Verify the settings by entering the show qos interface bandwidth command. CLI Reference Guide 505 - D-Link DGS-6600-48TS | CLI Guide - Page 516
DGS-6604 m qos cos qos cos To configure the default class of service (CoS) value of a port, use the qos cos command in interface configuration mode. qos cos COS-VALUE .1 switch(config-if)# qos cos 3 Verify the settings by entering the show qos interface cos command. CLI Reference Guide 506 - D-Link DGS-6600-48TS | CLI Guide - Page 517
DGS-6604 m qos deficit-round-robin qos deficit-round-robin Use the qos command in interface configuration mode to is subtracted from the corresponding credit counter. When the credit counter drops below 0, the queue is no longer serviced until its credits are replenished. CLI Reference Guide 507 - D-Link DGS-6600-48TS | CLI Guide - Page 518
DGS-6604 m Examples qos deficit-round-robin All queues are serviced until their credit counter is zero or negative and a packet is transmitted completely. As this config-if)# qos deficit-round-robin 6 quantum 2 Switch(config-if)# qos deficit-round-robin 7 quantum 0 CLI Reference Guide 508 - D-Link DGS-6600-48TS | CLI Guide - Page 519
DGS-6604 m qos deficit-round-robin In the following example, Weight round robin is configured on eth 3.1. For this case, queue 5, 6, and 7 0 Switch(config-if)# qos weight-round-robin 1 weight 2 Switch(config)# Verify the settings by entering the show qos interface command. CLI Reference Guide 509 - D-Link DGS-6600-48TS | CLI Guide - Page 520
DGS-6604 m qos dscp-mutation qos dscp-mutation To attach an ingress differentiated-services-code-point (DSCP Guideline Example Not configured Interface configuration Only Physical port interfaces are supported, port channel interface and vlan interface are not valid for . CLI Reference Guide 510 - D-Link DGS-6600-48TS | CLI Guide - Page 521
DGS-6604 m qos map cos-color qos map Guideline Example COS-LIST: 0-7 set to green Interface configuration Only Physical port interfaces are supported; port channel interface and vlan interface are not valid for this command. When a the show qos interface map command CLI Reference Guide 511 - D-Link DGS-6600-48TS | CLI Guide - Page 522
DGS-6604 m qos map dscp-color qos map dscp-color To define the DSCP to color map for mapping of packet's initial color, use the qos eth3.1 Swtich (config-if)# qos map dscp-color 61-63 to yellow Verify the settings by entering the show qos interface map command. CLI Reference Guide 512 - D-Link DGS-6600-48TS | CLI Guide - Page 523
DGS-6604 m qos map dscp-cos qos map dscp-cos To define a differentiated services code point (DSCP)-to-class of service (CoS) map, use the qos map dscp-cos command in global configuration mode. To show qos interface map privileged EXEC command to verify the settings. CLI Reference Guide 513 - D-Link DGS-6600-48TS | CLI Guide - Page 524
DGS-6604 m qos map dscp-mutation qos map dscp-mutation To define a named differentiated services code point (DSCP) mutation map, use the qos map dscp-mutation command in global configuration mode. to 10 Use the show qos map privileged EXEC command to verify the settings. CLI Reference Guide 514 - D-Link DGS-6600-48TS | CLI Guide - Page 525
DGS-6604 m qos trust qos trust To set the trust state of a port, use the qos trust command in interface configuration mode; to trust interface eth3.1 Switch(config-if)# qos trust dscp Switch(config-if)# end Verify the settings by entering the show qos interface command. CLI Reference Guide 515 - D-Link DGS-6600-48TS | CLI Guide - Page 526
DGS-6604 m reboot reR boot Use this command to reboot a module on the specified then the entire system (all modules) will reboot. Note: The following example reboots the whole system: DGS-6600:15#reboot Warning: This command will cause system reboot. Do you want to continue (y/n) [n]?y Save - D-Link DGS-6600-48TS | CLI Guide - Page 527
DGS-6604 m redistribute redistribute Use redistribute to redistribute routes from one routing domain into BGP. Use no command to disable route redistribution Switch(config-router)# end Switch# You can verify your settings by entering the show ip protocols bgp command. CLI Reference Guide 517 - D-Link DGS-6600-48TS | CLI Guide - Page 528
DGS-6604 m redistribute (OSPF) redistribute (OSPF) metric-type TYPE-VALUE: Type 2 external route Router configuration A router receiving a link-state protocol with an internal metric will consider the cost of the route from metric" is configured, use the specified value. CLI Reference Guide 518 - D-Link DGS-6600-48TS | CLI Guide - Page 529
DGS-6604 m Example redistribute (OSPF) 4. If the "default metric" is not configured, and the route is redistributed from BGP. The metric will be 1. redistribute bgp 100 Switch(config-router)#end Switch# Verify the settings by entering the show ip protocols ospf command. CLI Reference Guide 519 - D-Link DGS-6600-48TS | CLI Guide - Page 530
DGS-6604 m redistribute (IPv6 OSPF) redistribute other if no metric value is specified. TYPE-VALUE (Optional) IPv6 OSPF specifies the external link type associated with the default route advertised into the IPv6 OSPF routing domain. It can be router configuration command. CLI Reference Guide 520 - D-Link DGS-6600-48TS | CLI Guide - Page 531
DGS-6604 m Example redistribute (IPv6 OSPF) The default-metric command cannot be used to affect the metric used to advertise connected routes IPv6. Switch> enable Switch# configure terminal Switch(config)# router ipv6 ospf Switch(config-router)# redistribute rip metric 10 CLI Reference Guide 521 - D-Link DGS-6600-48TS | CLI Guide - Page 532
DGS-6604 m redistribute (RIP) redistribute (RIP) Use redistribute to redistribute routes from one routing domain into another routing domain. Use the redistributed route from other protocols to RIP process will be determined by the value of the "default-metric" command. CLI Reference Guide 522 - D-Link DGS-6600-48TS | CLI Guide - Page 533
DGS-6604 m Examples redistribute (RIP) 3. If the metric is specified as 0, the metric for the redistributed route from other protocols to RIP will ospf metric 11 Switch(config-router)# end Switch# Verify the settings by entering the show ip protocols rip command. CLI Reference Guide 523 - D-Link DGS-6600-48TS | CLI Guide - Page 534
DGS-6604 m redistribute (RIP IPv6) redistribute (RIP IPv6) Use redistribute to redistribute routes from one routing domain into another routing The metric value specified in the redistribute command supersedes the metric value specified using the default-metric command. CLI Reference Guide 524 - D-Link DGS-6600-48TS | CLI Guide - Page 535
DGS-6604 m Example redistribute (RIP IPv6) The following example causes the specified OSPF process routes to be redistributed into an RIPng . Switch > enable Switch # configure terminal Switch (config) # router ipv6 rip Switch (config-router) # redistribute ospf metric 10 CLI Reference Guide 525 - D-Link DGS-6600-48TS | CLI Guide - Page 536
DGS-6604 m remote-span remote-span Use the command to specify a VLAN as a RSPAN VLAN. Use the no form of the command to revert to a Switch(config-vlan)# remote-span Switch(config-vlan)#exit Switch(config)# You can verify your settings by entering the show vlan command. CLI Reference Guide 526 - D-Link DGS-6600-48TS | CLI Guide - Page 537
DGS-6604 m resequence access-list resequence access-list Use this command to re-sequence the priority of the access-list entries in an Switch(config)# show access-list ip R&D 1 permit tcp any 10.20.0.0 255.255.0.0 3 permit tcp any host 10.100.1.2 5 permit icmp any any CLI Reference Guide 527 - D-Link DGS-6600-48TS | CLI Guide - Page 538
DGS-6604 m revision revision To set the revision number for the MST configuration, use the revision command. To return to the spanning-tree mst configuration Switch(config-mst)#revision 2 Verify the settings by entering the show spanning-tree mst configuration command. CLI Reference Guide 528 - D-Link DGS-6600-48TS | CLI Guide - Page 539
DGS-6604 m rmon statistics rmon statistics Use the rmon the traffic for the interface. The administrator can also perform operations on the supported MIB RMON groups. This example shows how to create two RMON entries on eth3.2 Switch(config-if)#no rmon statistics 3 CLI Reference Guide 529 - D-Link DGS-6600-48TS | CLI Guide - Page 540
DGS-6604 m route-map route-map Use route-map to add the policy routing entry. Use the no form of the command to remove a policy routing be searched. If the no route-map MAP-TAG command is specified (with no SEQUENCE-NUM argument), the entire route map is deleted. CLI Reference Guide 530 - D-Link DGS-6600-48TS | CLI Guide - Page 541
DGS-6604 m Example route-map This example shows how to add the policy routing entry with name "myPolicy": Switch(config)# route-map myPolicy permit -map)#set weight 1000 Switch(config-route-map)#end Switch# Verify the settings by entering the show running-config command. CLI Reference Guide 531 - D-Link DGS-6600-48TS | CLI Guide - Page 542
DGS-6604 m router bgp router bgp Use this command to enable (configure) BGP routing process. Use the no form of the command to This example shows how to configure a BGP process for autonomous system 1.65534: Switch(config)# router bgp 1.65534 Switch(config-router)# CLI Reference Guide 532 - D-Link DGS-6600-48TS | CLI Guide - Page 543
DGS-6604 m router-id router-id Use this command to specify a router ID for ), the new router-ID will not take effect immediately. It will be used at the next reload or at a manual OSPF process restart. This example shows how to configure router id to 10.10.10.60 Switch# configure terminal Switch - D-Link DGS-6600-48TS | CLI Guide - Page 544
DGS-6604 m router-id (IPv6) router-id (IPv6) To assign a fixed router ID, use ), the new router ID will not take effect immediately. It is used at the next reload or at a manual restart of IPv6 OSPF process. The following example specifies a fixed router ID. Switch > enable Switch # configure - D-Link DGS-6600-48TS | CLI Guide - Page 545
DGS-6604 m router ipv6 rip router ipv6 rip To configure an IPv6 RIP routing process, use the router ipv6 rip command in global for the IPv6 RIP routing process. Switch > enable Switch # configure terminal Switch (config) # router ipv6 rip Switch(config-router)# end CLI Reference Guide 535 - D-Link DGS-6600-48TS | CLI Guide - Page 546
DGS-6604 m router ipv6 ospf router ipv6 ospf To enable the IPv6 OSPF routing process, use the router ipv6 ospf command in router OSPF for IPv6 configuration mode. Switch > enable Switch # configure terminal Switch (config) # router ipv6 ospf 0 Switch (config-router) # CLI Reference Guide 536 - D-Link DGS-6600-48TS | CLI Guide - Page 547
DGS-6604 m router ospf router ospf To configure an Open Shortest Path First (OSPF) routing process, use the router ospf command in configure terminal Switch(config)# router ospf Switch(config-router)# Verify the settings by entering the show ip protocols ospf command. CLI Reference Guide 537 - D-Link DGS-6600-48TS | CLI Guide - Page 548
DGS-6604 m router rip router rip no router rip Syntax Default Command Mode Usage Guideline Example router rip Use the command to configure terminal Switch(config)# router rip Switch(config-router)# end Verify the settings by entering the show ip protocols rip command. CLI Reference Guide 538 - D-Link DGS-6600-48TS | CLI Guide - Page 549
DGS-6604 m send-lifetime send-lifetime To set the time period during which an authentication key on a key chain is valid to be sent, use the first valid key will be used. If there are no valid keys during a specific period of time, then no authentication will be performed. CLI Reference Guide 539 - D-Link DGS-6600-48TS | CLI Guide - Page 550
DGS-6604 m Example send-lifetime The following example configures a key chain named chain1. Key 1 named "forkey1string" will be accepted from 1:30 p.m. to 3: -keychain-key)# exit Switch(config-keychain)# exit Verify the settings by entering the show ip key-chain command. CLI Reference Guide 540 - D-Link DGS-6600-48TS | CLI Guide - Page 551
DGS-6604 m server server Set up a server for different types of methods. Use the no form of this command to delete a server. server {tacacs | switch. The first created authentication method will be the primary one. The maximum number of entries in the list is project CLI Reference Guide 541 - D-Link DGS-6600-48TS | CLI Guide - Page 552
DGS-6604 m server dependent. However it is recommended client and the server. The privilege level can be set in TACACS+/RADIUS server. The supported privilege level is project dependent. Example If the wrong privilege level is configured or if aaa group server command. CLI Reference Guide 542 - D-Link DGS-6600-48TS | CLI Guide - Page 553
DGS-6604 m service dhcp service dhcp Use this command to enable a Dynamic Host Configuration Protocol (DHCP) server features on the switch. Use the no form of this command to disable DHCP server features. service dhcp no service terminal switch(config)# service dhcp CLI Reference Guide 543 - D-Link DGS-6600-48TS | CLI Guide - Page 554
DGS-6604 m service-policy service-policy To attach a policy map to an input interface use the service-policy command in the interface configuration mode. To remove a service policy from an input interface, use the no form of this command. service-policy NAME no service CLI Reference Guide 544 - D-Link DGS-6600-48TS | CLI Guide - Page 555
DGS-6604 m service-policy The cust1-classes policy map is configured and then attached to eth3.1 and -pmap-c)# exit Switch(config-pmap)# exit Switch(config)# interface eth3.1 Switch(config-if)# service-policy cust1-classes Switch(config-if)# exit Switch(config)# interface eth3.2 Switch(config-if - D-Link DGS-6600-48TS | CLI Guide - Page 556
DGS-6604 m service-policy The cust2-classes policy map is configured and then attached to (config-pmap-c)# exit Switch(config-pmap)# exit Switch(config)# interface eth4.1 Switch(config-if)# service-policy cust2-classes Switch(config-if)# exit Verify the settings by entering the show qos interface - D-Link DGS-6600-48TS | CLI Guide - Page 557
DGS-6604 m set set Use the set command in policy map class configuration mode to set the new precedence field, DSCP field, and CoS field of policy1 is configured with the policy for the class1 class. The packets that are included in the class1 class will be set to a CLI Reference Guide 547 - D-Link DGS-6600-48TS | CLI Guide - Page 558
DGS-6604 m set DSCP of 10 and policed by a singe rate policer with an average rate set to128 Kbits per second and the normal burst -action set-dscp-transmit 3 Switch(config-pmap-c)# exit Switch(config-pmap)# exit Verify the settings by entering the show policy-map command. CLI Reference Guide 548 - D-Link DGS-6600-48TS | CLI Guide - Page 559
DGS-6604 m set as-path set as-path Use this command to modify an autonomous system path for BGP routes. To delete an entry, use the myPolicy permit 1 Switch(config-route-map)#set as-path prepend 1 10 100 200 Verify the settings by entering the show route-map command. CLI Reference Guide 549 - D-Link DGS-6600-48TS | CLI Guide - Page 560
DGS-6604 m set community set community Use this command to set the BGP communities attribute, to delete an entry, use the no form of this transitive, Well-known community is not-transitive. This command is useful for routes received from EBGP and to be transmitted to IBGP. CLI Reference Guide 550 - D-Link DGS-6600-48TS | CLI Guide - Page 561
DGS-6604 m Example set community This example shows how to set a community (0:1) to the route map entry with name myPolicy: Switch(config)# Switch(config-route-map)# set community 0:1 Switch(config-route-map)# Verify the settings by entering the show route-map command. CLI Reference Guide 551 - D-Link DGS-6600-48TS | CLI Guide - Page 562
DGS-6604 m set default interface set default interface Use the command in route-map configuration mode to set the interface to route the packets Switch(config-if)#exit Switch(config)# You can verify your settings by entering the show route-map privileged EXEC command. CLI Reference Guide 552 - D-Link DGS-6600-48TS | CLI Guide - Page 563
DGS-6604 m set ip next-hop set ip next-hop Use this command to set the next-hop to route the packets that pass created access list, StrictControl. Lastly, in Vlan Interface configuration mode set the conditionally redistributed to previously created route-map, myPolicy. CLI Reference Guide 553 - D-Link DGS-6600-48TS | CLI Guide - Page 564
DGS-6604 m set ip next-hop Switch(config)# ip access-list Strict-Control Switch(config-ip-acl)# permit 10.1.1.0 255.255.255.0 any Switch( (config-router)# ip policy route-map myPolicy You can verify your settings by entering the show route-map privileged EXEC command. CLI Reference Guide 554 - D-Link DGS-6600-48TS | CLI Guide - Page 565
DGS-6604 m set ip precedence set ip precedence Use the set ip precedence command in route-map configuration mode to set the precedence value example Switch(config-if)#exit Switch(config)# You can verify your settings by entering the show route-map privileged EXEC command. CLI Reference Guide 555 - D-Link DGS-6600-48TS | CLI Guide - Page 566
DGS-6604 m set interface set interface Use the command in route-map configuration mode to set the interface to route the packets that pass a example Switch(config-if)#exit Switch(config)# You can verify your settings by entering the show route-map privileged EXEC command. CLI Reference Guide 556 - D-Link DGS-6600-48TS | CLI Guide - Page 567
DGS-6604 m set ipv6 default next-hop set ipv6 default next-hop Use the command in route-map configuration mode to set access list, Strict-Control. Lastly, in Vlan Interface configuration mode set the conditionally redistributed to previously created route-map, myPolicy. CLI Reference Guide 557 - D-Link DGS-6600-48TS | CLI Guide - Page 568
DGS-6604 m set ipv6 default next-hop Switch(config)# ipv6 access-list extended Strict-Control Switch(config-ip-acl)# permit 2000::3:4 ffff::0 any -router)# ip policy route-map myPolicy You can verify your settings by entering the show route-map privileged EXEC command. CLI Reference Guide 558 - D-Link DGS-6600-48TS | CLI Guide - Page 569
DGS-6604 m set ip default next-hop set ip default next-hop Use the command in route-map configuration mode to set the next create a route map, named myPolicy which define a match rule to associate ip address prefix-list to the previously created access list, StrictControl. CLI Reference Guide 559 - D-Link DGS-6600-48TS | CLI Guide - Page 570
DGS-6604 m set ip default next-hop Lastly, in Vlan Interface configuration mode set the conditionally redistributed to previously created route-map, myPolicy ip policy route-map myPolicy You can verify your settings by entering the show route-map privileged EXEC command. CLI Reference Guide 560 - D-Link DGS-6600-48TS | CLI Guide - Page 571
DGS-6604 m set ipv6 next-hop set ipv6 next-hop Use this command to set the next-hop to route the packets that pass a create a route map, named myPolicy which define a match rule to associate ip address prefix-list to the previously created access list, StrictControl. CLI Reference Guide 561 - D-Link DGS-6600-48TS | CLI Guide - Page 572
DGS-6604 m set ipv6 next-hop Lastly, in Vlan Interface configuration mode set the conditionally redistributed to previously created route-map, myPolicy. )# ip policy route-map myPolicy You can verify your settings by entering the show route-map privileged EXEC command. CLI Reference Guide 562 - D-Link DGS-6600-48TS | CLI Guide - Page 573
DGS-6604 m set default interface set default interface Use the command in route-map configuration mode to set the interface to route the packets map)# exit Switch(config)#interface vlan100 Switch(config-if)#ip policy route-map example Switch(config-if)#exit Switch(config)# CLI Reference Guide 563 - D-Link DGS-6600-48TS | CLI Guide - Page 574
DGS-6604 m set origin set origin To set the BGP origin code, use the set origin command in route-map configuration mode. To delete an entry -map)# match as-path PATH_ACL Switch(config-route-map)# set origin egp Verify the settings by entering the show route-map command. CLI Reference Guide 564 - D-Link DGS-6600-48TS | CLI Guide - Page 575
DGS-6604 m set weight set weight To specify the BGP weight for the routing table, use the set weight command in route-map configuration mode. -map)# match as-path PATH_ACL Switch(config-route-map)# set weight 30 Verify the settings by entering the show route-map command. CLI Reference Guide 565 - D-Link DGS-6600-48TS | CLI Guide - Page 576
DGS-6604 m sflow sflow no sflow Syntax Default Command Mode Usage Guideline Example sflow Use the sflow command to enable sFlow functions. send sFlow datagrams. User can still configure sFlow objects. This example shows how to enable sFlow functions. switch(config)# sflow CLI Reference Guide 566 - D-Link DGS-6600-48TS | CLI Guide - Page 577
DGS-6604 m sflow receiver sflow receiver Use the IPV6-ADDRESS (Optional) The IPv6 address of the remote sFlow collector. It does not support IPv6 link local addresses. udp-port PORT (optional) The UDP port of the remote sFlow collector, the no sflow receiver command. CLI Reference Guide 567 - D-Link DGS-6600-48TS | CLI Guide - Page 578
DGS-6604 m Example sflow receiver Use the no sflow receiver command to reset the Receiver. When a Receiver expired, the Receiver is disabled and PORT as 6343. switch(config)# sflow receiver 1 owner collector1 expiry 86400 max-datagramsize 1400 host 10.1.1.2 udp-port 6343 CLI Reference Guide 568 - D-Link DGS-6600-48TS | CLI Guide - Page 579
DGS-6604 m sflow sampler sflow sampler Use the sflow sampler command to create/configure a Sampler for the sFlow agent. Use the no form of this . This example shows how to create/configure the Sampler of INSTANCE 1 with RECEIVER as 1, RATE as 1024 and SIZE as 128 bytes. CLI Reference Guide 569 - D-Link DGS-6600-48TS | CLI Guide - Page 580
DGS-6604 m sflow sampler switch(config-if)# sflow sampler 1 receiver 1 sampling-rate 1024 max-headersize 128 CLI Reference Guide 570 - D-Link DGS-6600-48TS | CLI Guide - Page 581
DGS-6604 m sflow poller sflow poller Use the sflow poller command to create/configure a Poller for the sFlow agent. Use the no form configure the Poller of INSTANCE 1 with RECEIVER as 1, and INTERVAL as 20 seconds. switch(config-if)# sflow poller 1 receiver 1 interval 20 CLI Reference Guide 571 - D-Link DGS-6600-48TS | CLI Guide - Page 582
DGS-6604 m show aaa show aaa Use show aaa to display the login/enable method list for all applications. show aaa [login | enable] [console | telnet all applications. If the brief option is specified, the detailed server list of the associating method list will be skipped. CLI Reference Guide 572 - D-Link DGS-6600-48TS | CLI Guide - Page 583
to display the login/enable method list for all applications. show aaa DGS-6604:15#show aaa Console Session: Login authentication: Local Authentication: yes : Login authentication: Local Authentication: yes Enable authentication: Local Authentication: yes DGS-6604:15# CLI Reference Guide 573 - D-Link DGS-6600-48TS | CLI Guide - Page 584
: show aaa DGS-6604:15#show DGS-6604:15# The following example displays brief information for enable authentication: DGS and the telnet application: DGS-6604:15#show aaa DGS-6604:15# The following example displays brief information for authentication and the console application: DGS - D-Link DGS-6600-48TS | CLI Guide - Page 585
DGS-6604 m show aaa group server show aaa group server Use this command show aaa group server to display the Key authserv 10.1.1.1 XTACACS 49 5 2 authserv 20.1.1.1 RADIUS 1812 5 2 ********** authserv 20.1.1.2 RADIUS 1812 5 2 no-encrypt Switch:15# CLI Reference Guide 575 - D-Link DGS-6600-48TS | CLI Guide - Page 586
DGS-6604 m show access-group show access-group Use this command to display how the mac, ip and ipv6 access-lists are applied to interfaces. -list : ip6-control eth3.2 Inbound mac access-list : rd-mac-acl Inbound ip access-list : rd-ip-acl Inbound ipv6 access-list : N/A CLI Reference Guide 576 - D-Link DGS-6600-48TS | CLI Guide - Page 587
DGS-6604 m show access-list Use this command to display the access-list configuration. show access-list [ ip NAME | mac NAME | ipv6 NAME] show access-list access-list ip R&D 10 permit tcp any 10.20.0.0 255.255.0.0 20 permit tcp any host 10.100.1.2 30 permit icmp any any CLI Reference Guide 577 - D-Link DGS-6600-48TS | CLI Guide - Page 588
DGS-6604 m show arp show arp Use the show arp command to display the Address Resolution Protocol (ARP) cache. show arp [ARP-MODE] [IP-ADDRESS [/ MASK]] [ 00-00-a7-10-85-9b vlan200 Dynamic 10.108.42.121 00-00-a7-10-68-cd vlan300 Dynamic Total Entries: 3 Switch# CLI Reference Guide 578 - D-Link DGS-6600-48TS | CLI Guide - Page 589
DGS-6604 m show boot show boot Syntax Default Command Mode Usage Guideline Example show boot Use this command to display which is the next Boot loader version 1.00.004 Boot image: flash:\switch-image1.had, flash:\switch-image2.had Boot config: flash:\switch-config Switch# CLI Reference Guide 579 - D-Link DGS-6600-48TS | CLI Guide - Page 590
DGS-6604 m show channel-group show channel-group Use this command to display the information of channel groups. show channel-group [[channel [CHANNEL-NO] [detail | neighbor eth3.1 32768,00-07-eb-49-5e-80 12 SP 32768 eth3.2 32768,00-07-eb-49-5e-80 13 SP 32768 Switch> CLI Reference Guide 580 - D-Link DGS-6600-48TS | CLI Guide - Page 591
DGS-6604 m show channel-group This example shows how to display the detailed information of all port-channels. Switch> show channel-group 32768 11 Channel Group 2 Member Ports: 2, Maxports = 8, Protocol: Static LACP Port State eth3.8 bndl eth3.9 down Switch> CLI Reference Guide 581 - D-Link DGS-6600-48TS | CLI Guide - Page 592
DGS-6604 m show channel-group This example shows how to display the protocol information for all port-channels. Switch> show channel-group balance information for all channel groups. Switch> show channel-group load-balance load-balance algorithm: src-dst-mac Switch> CLI Reference Guide 582 - D-Link DGS-6600-48TS | CLI Guide - Page 593
DGS-6604 m show channel-group This example shows how to display the system identifier information Switch> show channel-group sys-id 32765,00-02 Group Protocol 1 LACP 2 Static Total Entries: 2 load-balance algorithm: src-dst-mac system-ID: 32765,00-02-4b-29-3a-00 CLI Reference Guide 583 - D-Link DGS-6600-48TS | CLI Guide - Page 594
DGS-6604 m show class-map Use this command to display the class map configuration. show class-map [NAME] show class-map Syntax Description NAME ( -map Class Map match-any c2 match protocol ip Class Map match-any c3 match access-list acl_home_user Total Entries: 2 Switch# CLI Reference Guide 584 - D-Link DGS-6600-48TS | CLI Guide - Page 595
DGS-6604 m show clock show clock Syntax Default Command Mode Usage Guideline Example show clock Use this command to display the time and date information Saving Time : Recurring Offset in Minutes : 60 Recurring From : Apr 2nd Tue 15:00 To : Oct 2nd Wed 15:30 Switch> CLI Reference Guide 585 - D-Link DGS-6600-48TS | CLI Guide - Page 596
DGS-6604 m show cpu-protect safeguard show cpu-protect safeguard Use this command to display the settings and status of -protect safeguard Safeguard Engine State Safeguard Engine Status : Disabled : Normal Utilization Thresholds: Rising : 50% Falling : 20% Switch# CLI Reference Guide 586 - D-Link DGS-6600-48TS | CLI Guide - Page 597
DGS-6604 m show cpu-protect type show cpu-protect type Use this 0 0 icmpv6-other 0 0 0 pim 0 0 0 rip 0 0 0 ospf 0 0 0 !--- Output suppressed. Switch# CLI Reference Guide The following example is a sample output of the show cpu-protect type arp command. The configured rate is - D-Link DGS-6600-48TS | CLI Guide - Page 598
DGS-6604 m Switch# show cpu-protect type arp Type: arp Pps : 300 Slot Total Drop 1 (CM-card) 30 0 3 30 0 Switch# show cpu-protect type CLI Reference Guide 588 - D-Link DGS-6600-48TS | CLI Guide - Page 599
DGS-6604 m show cpu-protect sub-interface show cpu-protect sub-interface Use this command to show the rate-limit and interface. Switch# show cpu-protect sub-interface protocol Sub-Interface: protocol Pps : N/A Slot Total Drop 1(CM-card) 0 0 3 0 0 Switch# CLI Reference Guide 589 - D-Link DGS-6600-48TS | CLI Guide - Page 600
DGS-6604 m show ddm show ddm Syntax Default Command Mode Usage Guideline Example show ddm This command displays the DDM global setting. None None of DDM. The following example shows how to display DDM global setting. Switch# show ddm DDM Log : Enabled DDM Trap : Disabled CLI Reference Guide 590 - D-Link DGS-6600-48TS | CLI Guide - Page 601
DGS-6604 m show ddm status show ddm status This command displays the current operating parameters of the SFP modules. show ddm status [INTERFACE-ID 3.372 0.000 0.0000 0.0000 eth3.25 32.539 3.292 5.220 0.5300 0.0641 eth3.26 31.328 3.302 5.408 0.5300 0.0659 CLI Reference Guide 591 - D-Link DGS-6600-48TS | CLI Guide - Page 602
DGS- 26) Switch# show ddm configuration eth3.23-3.26 Interface eth3.23 (Not support DDM DDM state : Enabled Shutdown : None Temperature Voltage Bias Current TX Alarm - - - - - Interface eth3.24 (No optical module detected) DDM state : Enabled Shutdown : None CLI Reference Guide 592 - D-Link DGS-6600-48TS | CLI Guide - Page 603
DGS-6604 m show ddm configuration Temperature Voltage Bias Current TX Power RX Power Threshold (Celsius) (V) (mA) (mW) (mW) High Alarm - - - - - High Warning - - - - - 000 3.135 2.500 0.1862 0.1023 Low Alarm -5.000 2.970 2.000 0.0741 0.0407 CLI Reference Guide 593 - D-Link DGS-6600-48TS | CLI Guide - Page 604
DGS-6604 m show dos_prevention show dos_prevention Use this command to show DoS prevention status and related drop counters. show dos_prevention Disabled TCP Null Disabled TCP Xmas Disabled TCP SYNFIN Disabled TCP SYN SrcPort Less Than 1024 Disabled Switch# CLI Reference Guide 594 - D-Link DGS-6600-48TS | CLI Guide - Page 605
DGS-6604 m show dot1v show dot1v Use the show dot1v command to display the setting for the configuration of VLAN protocols. show dot1v interface eth3.1-3.3 Interface dot1v Group ID/Binding-VLAN eth3.1 1/1 eth3.2 10/3000, 11/3001, 12/3002 eth3.3 2/100 Switch# CLI Reference Guide 595 - D-Link DGS-6600-48TS | CLI Guide - Page 606
DGS-6604 m show dot1x show dot1x Use this command to display information about the: 802.1X state, configuration, statistics, diagnostics, Period: 3600 Re-authentication: Disabled Authentication Mode: Host-based Guest VLAN: Disabled Forward 1x PDU: Disabled Total Entries: 1 CLI Reference Guide 596 - D-Link DGS-6600-48TS | CLI Guide - Page 607
DGS-6604 m show dot1x This example shows how to display the authentication statistics for port eth4.1. Switch#show dot1x interface eth4.1 statistics eth4.1 -Length Error Frames RX: 0 Last EAPOL Frame Version: 0 Last EAPOL Frame Source: 00-00-00-00-00-00 Total Entries: 1 CLI Reference Guide 597 - D-Link DGS-6600-48TS | CLI Guide - Page 608
DGS-6604 m show dot1x This example shows how to display the authentication diagnostics for port eth4.1. 0 SessionFramesRX: 0 SessionFramesTX: 0 SessionId: SessionAuthenticationMethod: SessionTime: 0 SessionTerminateCause: PortAdminDisabled SessionUserName: Total Entries: 1 CLI Reference Guide 598 - D-Link DGS-6600-48TS | CLI Guide - Page 609
DGS-6604 m show dot1x vlan Use this command to show the vlan assigned by dot1x module. show dot1x vlan Syntax None Default None Command Mode the output of this command. show dot1x vlan Switch#show dot1x vlan Port VID eth3.17 100 eth3.18 101 Total Entries: 2 Switch# CLI Reference Guide 599 - D-Link DGS-6600-48TS | CLI Guide - Page 610
DGS-6604 m show dot1x user show dot1x user Use this command to show the local accounts for 802.1x authentication. show example shows the output of this command. Switch#show dot1x user Username Password yourname1 yourpass1 yourname2 yourpass2 Total Entries: 2 CLI Reference Guide 600 - D-Link DGS-6600-48TS | CLI Guide - Page 611
DGS-6604 m show errdisable recovery show errdisable recovery Use this command to display the error-disable recovery timer related setting recovered at the next timeout: Interface --------eth2.4 Errdisable Reason loopback-detection Time left(sec 179 Total Entries: 1 CLI Reference Guide 601 - D-Link DGS-6600-48TS | CLI Guide - Page 612
DGS-6604 m show enable password show enable password Use this command to display the password of the privilege Encryption : Disabled Access Level Password 12 mypassword (Plain Text) 15 *@&cRDtpNCeBiq15KOQsKVyrA0sAiCIZQwq (Encrypted) Total Entries: 2 Switch# CLI Reference Guide 602 - D-Link DGS-6600-48TS | CLI Guide - Page 613
DGS-6604 m show environment show environment Use the show environment command to display fan, temperature, redundant power system (RPS) availability, and mode If a specific environment type is not specified, then all types of environment information will be displayed. CLI Reference Guide 603 - D-Link DGS-6600-48TS | CLI Guide - Page 614
DGS-6604 m Example show environment The example shows how to display the H/W environmental information.This example includes the Status Power module #1 Power status in-operation Max power 850 W Used power 203 W #2 empty - #3 empty - #4 empty - Switch# CLI Reference Guide 604 - D-Link DGS-6600-48TS | CLI Guide - Page 615
DGS-6604 m Field Max power Used power Power status show environment The table below describes the significant fields shown in the display rectifier is in normal operation mode. failed: The power rectifier can't work normally. empty: The power rectifier is not installed. CLI Reference Guide 605 - D-Link DGS-6600-48TS | CLI Guide - Page 616
DGS-6604 m show gvrp configuration show gvrp configuration Use the show gvrp command to display the settings for gvrp. show gvrp configuration [ gvrp configuration. Switch# show gvrp configuration Global GVRP State : Enabled Dynamic Vlan Creation : Disabled Switch# CLI Reference Guide 606 - D-Link DGS-6600-48TS | CLI Guide - Page 617
DGS-6604 m show gvrp configuration This example shows how to display the GVRP configuration for port's eth3.5 to Port Forbidden VLANs eth3.5 3,5 eth3.6 5-8 Port based Advertising VLAN Configuration: Port Advertising VLANs: eth3.5 1,3 eth3.6 1,9 Switch# CLI Reference Guide 607 - D-Link DGS-6600-48TS | CLI Guide - Page 618
DGS-6604 m show gvrp statistics show gvrp statistics Use the show gvrp statistics command to display the Empty eth3.5 . RX 0 0 0 0 0 TX 4294967296 4294967296 4294967296 4294967296 4294967296 eth3.6 . RX 0 0 0 0 0 TX 0 0 0 0 0 Total Entries: 2 CLI Reference Guide 608 - D-Link DGS-6600-48TS | CLI Guide - Page 619
DGS-6604 m show history show history To list the commands that have been entered in the current EXEC session, use the show history command. is fixed at 20 commands. Example This example shows how to show the command history. Switch#show history 1 help 2 history Switch# CLI Reference Guide 609 - D-Link DGS-6600-48TS | CLI Guide - Page 620
DGS-6604 m show interface show interface Use this command to display information about a specified interface or all interfaces. show interface [ 0, TX Excessive Deferral: 0 TX Single Collision: 0, TX Excessive Collision: 0 TX Late Collision: 0, TX Collision: 0 Switch# CLI Reference Guide 610 - D-Link DGS-6600-48TS | CLI Guide - Page 621
DGS-6604 m show interface This example is a sample output of information for interface port channel 1. Switch#show interface port-channel1 port-channel1 is down, line ) Hardware is VLAN, address is 08-01-02-38-00-01 (bia 08-01-02-38-00-01) Description: IP MTU:1500bytes CLI Reference Guide 611 - D-Link DGS-6600-48TS | CLI Guide - Page 622
DGS-6604 m show interface status err-disabled show interface status err-disabled Use this command to display a list of interfaces in Reason eth2.8 err-disabled loopback-detection eth4.17 err-disabled loopback-detection eth3.10 err-disabled loopback-detection CLI Reference Guide 612 - D-Link DGS-6600-48TS | CLI Guide - Page 623
DGS-6604 m show ip as-path access-list show ip as-path access-list To display configured as-path access-lists, use the show ip as- AS path access-list Switch>Show ip as-path access-list AS path access list A1 permit .* AS path access list A2 permit .* CLI Reference Guide 613 - D-Link DGS-6600-48TS | CLI Guide - Page 624
DGS-6604 m show ip bgp show ip bgp To display entries in the Border Gateway Protocol (BGP) routing table, Network *> 10.1.1.0/24 *> 172.17.1.0/24 Next Hop 0.0.0.0 192.168.1.1 Metric 0 0 LocPrf Weight 32768 0 Path i 45000 i Total Entries: 2 entries, 2 routes Switch> CLI Reference Guide 614 - D-Link DGS-6600-48TS | CLI Guide - Page 625
DGS-6604 m show ip bgp The following is example output from the show ip bgp command entered with the route-map keyword: Switch(config)#show ip .71.200 (10.50.71.200) Origin IGP, localpref 100, valid, external, best Last update: 19:47:01, 2010-09-29 Switch(config)# CLI Reference Guide 615 - D-Link DGS-6600-48TS | CLI Guide - Page 626
DGS-6604 m show ip bgp community-list show ip bgp community-list To display configured community lists, use the show ip community-list 22.1 0 100 0 1800 701 i *>i 10.0.16.1 0 100 0 1800 701 i * 10.92.72.24 0 1878 704 701 i Total Entries: 7 entries, 18 routes CLI Reference Guide 616 - D-Link DGS-6600-48TS | CLI Guide - Page 627
DGS-6604 m show ip bgp community-list Field BGP table version local router ID Status codes Origin codes Network Next Hop Metric LocPrf Weight Path system paths to the destination network. There can be only one entry in this field for each autonomous system in the path. CLI Reference Guide 617 - D-Link DGS-6600-48TS | CLI Guide - Page 628
DGS-6604 m show ip bgp filter-list show ip bgp filter-list To display routes that conform to a specified filter list, use the show ip bgp .16.38.0 172.16.72.30 0 109 108 ? * 172.16.39.0 172.16.72.30 0 109 108 ? Total Entries: 18 entries, 18 routes CLI Reference Guide 618 - D-Link DGS-6600-48TS | CLI Guide - Page 629
DGS-6604 m show ip bgp neighbors show ip bgp neighbors Use this command to display information about the TCP and Border Gateway Protocol (BGP if the keyword ipv4 is not specified. Specify the IP address of a neighbor to display information about the specific neighbor. CLI Reference Guide 619 - D-Link DGS-6600-48TS | CLI Guide - Page 630
neighbor supports the route refresh and graceful restart capabilities. Switch# show ip bgp neighbors 10.50.71.253 BGP neighbor is 10.50.71.253, remote AS 8001, local AS 8001, internal link Member 2 accepted prefixes 3 announced prefixes Connections established 1; dropped 0 CLI Reference Guide 620 - D-Link DGS-6600-48TS | CLI Guide - Page 631
DGS-6604 m show ip bgp neighbors Graceful-restart Status: Remote restart-time is 120 sec Local host: 10.50.71.254, i10.0.0.0 *> 10.20.2.0 Next Hop 172.16.232.179 10.0.0.0 Metric 0 0 LocPrf Weight 100 0 32768 Path ? i Total Entries: 2 entries, 2 routes Swtich> CLI Reference Guide 621 - D-Link DGS-6600-48TS | CLI Guide - Page 632
DGS-6604 m show ip community-list show ip community-list To display configured community lists, use the show ip community-list command. )#show ip community-list Named Community standard list C1 permit internet Named Community standard list C2 permit 3:2 Switch(config)# CLI Reference Guide 622 - D-Link DGS-6600-48TS | CLI Guide - Page 633
DGS-6604 m show ip dhcp binding show ip dhcp binding To display the current status of address bindings on the DHCP Server. show ip dhcp binding [ 18:38:56, 2010-09-30 Lease expiration 18:38:56, 2010-10-1 18:38:56, 2010-10-1 18:38:56, 2010-10-1 CLI Reference Guide 623 - D-Link DGS-6600-48TS | CLI Guide - Page 634
DGS-6604 m show ip dhcp binding The following example shows the binding status of IP address 10.1.1.1 in DHCP address pool, pool1. switch# Hardware address Lease start ---------- 10.1.1.1 00b8.3493.32b5 18:38:56, 2010-09-30 Lease expiration 18:38:56, 2010-10-1 CLI Reference Guide 624 - D-Link DGS-6600-48TS | CLI Guide - Page 635
DGS-6604 m show ip dhcp conflict show ip dhcp conflict To display the conflict IP addresses while a DHCP Server attempts to assign the IP -09-30 Pool name: pool3 IP address Detected Method ---------- 172.1.1.1 Gratuitous ARP Detection time 18:38:56, 2010-09-30 CLI Reference Guide 625 - D-Link DGS-6600-48TS | CLI Guide - Page 636
DGS-6604 m show ip dhcp pool show ip dhcp pool To display information about the Dynamic Host Configuration Protocol (DHCP) address pools, show ip dhcp setting of the address pool. If the NAME argument is not used then the information for all the pools will be displayed. CLI Reference Guide 626 - D-Link DGS-6600-48TS | CLI Guide - Page 637
DGS-6604 m Example show ip dhcp pool The following example shows DHCP address pool information for an OnDemand Address Pool (ODAP), Display Field Descriptions Descriptions of the significant fields in the previous example. Field Pool Description The name of the pool. CLI Reference Guide 627 - D-Link DGS-6600-48TS | CLI Guide - Page 638
DGS-6604 m show ip dhcp pool Field Subnet ID The address binding rule based on customer vlan id The address binding rule based on service provider vlan id The address binding rule based on ingress interface IP The address binding rule are conflict with other clients. CLI Reference Guide 628 - D-Link DGS-6600-48TS | CLI Guide - Page 639
DGS-6604 m show ip dhcp relay Display the IP DHCP relay agent configuration. show ip dhcp relay show ip dhcp relay IP Addresses 10.1.1.1, 10.1.1.2 , 10.1.1.3 , 0.0.0.0 List of Trusted sources of relay agent information option: VLAN100 VLAN200 VLAN300 Switch# VLAN400 CLI Reference Guide 629 - D-Link DGS-6600-48TS | CLI Guide - Page 640
DGS-6604 m show ip dhcp relay information trusted-sources show ip dhcp relay information trusted-sources Use the show ip dhcp relay trusted-sources List of trusted sources of relay agent information option: VLAN100 VLAN200 VLAN300 VLAN400 VLAN500 Total Entries: 5 Switch# CLI Reference Guide 630 - D-Link DGS-6600-48TS | CLI Guide - Page 641
DGS-6604 m show ip dhcp server show ip dhcp server This command displays the current status of DHCP server show ip dhcp server timeout: 500 ms List of DHCP server configured address pool pool1 pool5 pool9 pool2 pool6 pool10 pool3 pool7 pool11 pool4 pool8 pool12 CLI Reference Guide 631 - D-Link DGS-6600-48TS | CLI Guide - Page 642
DGS-6604 m show ip dhcp server statistics show ip dhcp server statistics To display Dynamic Host Configuration Protocol (DHCP) server statistics. show pools in the DHCP database. The number of truncated or corrupted messages that were received by the DHCP server. CLI Reference Guide 632 - D-Link DGS-6600-48TS | CLI Guide - Page 643
DGS-6604 m Field Renew messages Message Received Sent show ip dhcp server statistics Description The number of renew messages for a DHCP lease. The counter DHCP messages that were received by the DHCP server. The number of DHCP messages that were sent by the DHCP server. CLI Reference Guide 633 - D-Link DGS-6600-48TS | CLI Guide - Page 644
DGS-6604 m show ip dhcp snooping Use this command to display DHCP snooping configuration. show ip dhcp snooping Syntax Description Not vlan15-18 Information option: not allowed Interface Trusted Rate Limit eth3.1 no 10 eth3.8 no 50 eth3.9 yes Switch# CLI Reference Guide 634 - D-Link DGS-6600-48TS | CLI Guide - Page 645
DGS-6604 m show ip dvmrp interface show ip dvmrp interface This command is used to display dvrmp configuration information on #show ip dvmrp interface vlan1000 Interface Address Metric Generation ID vlan1000 10.0.0.254 1 1234567890 Total Entries: 1 Switch# CLI Reference Guide 635 - D-Link DGS-6600-48TS | CLI Guide - Page 646
DGS-6604 m show ip dvmrp neighbor Use this command to show DVMRP neighbor information. show ip dvmrp neighbor [INTERFACE-ID | IP-ADDRESS] [detail] in the generation ID is detected, any prune information received from the router is no longer valid and should be flushed. CLI Reference Guide 636 - D-Link DGS-6600-48TS | CLI Guide - Page 647
DGS-6604 m ExpTime show ip dvmrp neighbor The neighbor time-out interval, which SHOULD be router sends Generation Id's. MTRACE - This neighbor router handles Mtrace requests. SNMP - This neighbor router supports the DVMRP MIB. Network - This neighbor will accept a network mask. CLI Reference - D-Link DGS-6600-48TS | CLI Guide - Page 648
DGS-6604 m UpTime ExpTime Generation ID show ip dvmrp neighbor The total time elapsed since the neighbor was discovered; until now. The time change in the generation ID is detected, any prune information received from the router is no longer valid and should be flushed. CLI Reference Guide 638 - D-Link DGS-6600-48TS | CLI Guide - Page 649
upstream Prune state information. Example This example shows how to displays prune information. DGS-6600:15#show ip dvmrp prune Flags: P=Pruned,D=Holddown,N=NegMFC Source Group State the Prune retransmit timer, otherwise, it would represent the Graft retransmit timer. CLI Reference Guide 639 - D-Link DGS-6600-48TS | CLI Guide - Page 650
any configuration mode Display DVMRP route information. This example shows how to display route information. DGS-6600:15#show ip dvmrp route State: H = Hold-down Source Network Upstream Neighbor Metric Learned is not going to be removed (because it is a local interface). CLI Reference Guide 640 - D-Link DGS-6600-48TS | CLI Guide - Page 651
DGS-6604 m show ip igmp group Used to display IGMP group information on an interface show ip igmp group [IP-ADDRESS | interface INTERFACE-ID] [detail] The number of the igmp group table display. The number of the group records and source records in the igmp group table. CLI Reference Guide 641 - D-Link DGS-6600-48TS | CLI Guide - Page 652
DGS-6604 m show ip igmp group This example shows how to display IGMP group detailed information for group 224.1.1.1. If the : 224.1.1.1 Uptime : 0DT0H0M42S Expires : 0DT0H3M38S Group mode : Exclude, dynamic Last reporter : 192.168.51.111 Source list is empty CLI Reference Guide 642 - D-Link DGS-6600-48TS | CLI Guide - Page 653
DGS-6604 m Display Field Descriptions Description of significant display fields. show ip igmp group Display Field Uptime Expires Group mode Last being a member of the multicast group. Status of whether the router is forwarding multicast traffic due to this entry. CLI Reference Guide 643 - D-Link DGS-6600-48TS | CLI Guide - Page 654
DGS-6604 m show ip igmp interface Used to display IGMP configuration information on interface show ip igmp interface [INTERFACE-ID [ , 95.90 Querier Timer countdown value : - Configured Query Interval : 5 Configured Maximum response time : 15 Configured Robustness : 2 CLI Reference Guide 644 - D-Link DGS-6600-48TS | CLI Guide - Page 655
DGS-6604 m show ip igmp snooping show ip igmp snooping Use this command to display IGMP Snooping information on the v3)1 Enabled Active Enabled - (v2)2 Disabled - Disabled 0DT0H4M10S (v3)3 Enabled Non-active Enabled 0DT0H3M12S Total number of VLANs = 3 Switch> CLI Reference Guide 645 - D-Link DGS-6600-48TS | CLI Guide - Page 656
DGS-6604 m Display Field Descriptions show ip igmp snooping The following table shows the field information for the above example. Display Field Querier its initial count is set to the value got from the Older Version Querier Present Timeout in the IGMP control packet. CLI Reference Guide 646 - D-Link DGS-6600-48TS | CLI Guide - Page 657
DGS-6604 m show ip igmp snooping group show ip igmp snooping group Use eth3.1 Total Entries : 3 entries, 6 records Display Field Descriptions Field entries records CLI Reference Guide show ip igmp snooping group Field Descriptions. Description The number of the igmp snooping group table display - D-Link DGS-6600-48TS | CLI Guide - Page 658
DGS-6604 m show ip igmp snooping group This example shows how to display the IGMP snooping group detailed information of group : eth3.2 Uptime : 0DT0H0M42S Expires : 0DT0H3M38S Group mode : Exclude, dynamic Last reporter: 192.168.51.111 Source list is empty Switch# CLI Reference Guide 648 - D-Link DGS-6600-48TS | CLI Guide - Page 659
DGS-6604 m Display Field Descriptions show ip igmp snooping group The following table shows the display field information for the example on the to report being a member of the multicast group. Status of whether the router is forwarding multicast traffic due to this entry. CLI Reference Guide 649 - D-Link DGS-6600-48TS | CLI Guide - Page 660
DGS-6604 m show ip igmp snooping mode This command is used to display information on dynamically learned and manually configured multicast router interfaces. When IGMP snooping is enabled, the switch Designate : eth4.4, Auto : eth3.2, Not-allowed: - Total Entries: 2 CLI Reference Guide 650 - D-Link DGS-6600-48TS | CLI Guide - Page 661
DGS-6604 m show ip interface Use this command to is specified, then information for that specific interface is displayed. This command only supports VLAN interface types. If no optional arguments are specified, then information for all up up Total Entires: 2 Switch> CLI Reference Guide 651 - D-Link DGS-6600-48TS | CLI Guide - Page 662
DGS-6604 m show ip interface This example shows how to display the ip interface information for VLAN 1 Switch> show ip interface vlan1 vlan1 is up, Internet is 110.0.0.1/24 MAC Address is 08-01-02-24-00-01 ARP timeout is 14400 seconds IP MTU is 1500 bytes (secondary) CLI Reference Guide 652 - D-Link DGS-6600-48TS | CLI Guide - Page 663
DGS-6604 m show ip key-chain show ip key-chain Use this command to display the settings of the configured key chains. show ip key-chain [ 25 2008) - (15:29:59 Feb 25 2008) send lifetime (14:30:00 Feb 25 2008) - (16:29:59 Feb 25 2008) Switch# CLI Reference Guide 653 - D-Link DGS-6600-48TS | CLI Guide - Page 664
DGS-6604 m show ip mroute show ip mroute Use this command to display the content of the IP multicast routing table. show ip mroute will renew itself. If network address is specified, the switch displays the entries with source addresses that match the specified address. CLI Reference Guide 654 - D-Link DGS-6600-48TS | CLI Guide - Page 665
DGS-6604 m Example show ip mroute This example shows how to display the IP multicast route table summary: Switch> show ip .1.1.1, distance: 0 Mroute: 192.168.7.0/24, RPF neighbor: 10.1.1.1, distance: 100 Mroute: 192.168.8.0/24, interface: Null, distance: 0 Total Entries: 3 CLI Reference Guide 655 - D-Link DGS-6600-48TS | CLI Guide - Page 666
DGS-6604 m show ip ospf show ip ospf Use this command to display general information about the OSPF routing process. show ip ospf Syntax None the LSA table size. It is project dependent. Example On the following page is a sample output from the show ip ospf command. CLI Reference Guide 656 - D-Link DGS-6600-48TS | CLI Guide - Page 667
DGS-6604 m show ip ospf Switch#show ip ospf Operational Router ID 10.47.65.160 Process uptime is 0DT0H12M33S Conforms to RFC2328, and executed 0DT0H9M46S ago SPF algorithm executed 7 times Number of LSA 32 Network 47.65.51.0/29 Network 47.65.52.0/29 Switch# CLI Reference Guide 657 - D-Link DGS-6600-48TS | CLI Guide - Page 668
DGS-6604 m show ip ospf border-routers show ip ospf border-routers Use this command to display the ABRs and ASBRs for the via 47.65.52.2, vlan52, ASBR, TransitArea 0.0.0.1 i 47.65.151.111 [2] via 47.65.53.2, vlan53, ASBR, TransitArea 0.0.0.2 Total Entries: 6 Switch# CLI Reference Guide 658 - D-Link DGS-6600-48TS | CLI Guide - Page 669
DGS-6604 m show ip ospf database show ip ospf database Use this command to display a database summary for OSPF information. show ip ospf the database summary for OSPF information. Example The following page shows a sample output from the show ip ospf database command: CLI Reference Guide 659 - D-Link DGS-6600-48TS | CLI Guide - Page 670
DGS-6604 m show ip ospf database Switch#show ip ospf database Router Link States (Area 0.0.0.0) Link ID 10.47.65.160 ADV Router 10.47.65.160 Age Seq# CkSum Link count 1765 0x8000000e 0x107f 6 Link ID 47.65.49.111 Net Link States (Area 0.0.0.0) ADV Router 47.65.49.111 Age Seq# CkSum - D-Link DGS-6600-48TS | CLI Guide - Page 671
DGS-6604 m show ip ospf database asbr-summary show ip ospf database asbr-summary Use this command to display information about the Autonomous System Boundary Router (ASBR) summary LSAs. show ip ospf database asbr-summary [LINK show ip ospf database asbr-summary command. CLI Reference Guide 661 - D-Link DGS-6600-48TS | CLI Guide - Page 672
(Area 0.0.0.1) LS age: 927 Options: 0x2 E|-) LS Type: ASBR-summary-LSA Link State ID: 10.47.65.183 (AS Boundary Router address) Advertising Router: 10.47.65.160 LS Seq Number: 80000001 Checksum: 0x53ba Length: 28 Network Mask: /0 TOS: 0 Metric: 1 Total Entries: 2 Switch# CLI Reference Guide 662 - D-Link DGS-6600-48TS | CLI Guide - Page 673
DGS-6604 m show ip ospf database external show ip ospf database external Use this command to display information about the external LSAs. show ip ospf database external [LINK-STATE-ID | self-originate | adv-router IP-ADDRESS] Syntax Description LINK-STATE-ID Link State ID (as an IP address). - D-Link DGS-6600-48TS | CLI Guide - Page 674
DGS-6604 m show ip ospf database network show ip ospf database network Use this command to display information about the network LSAs. show ip ospf database external [LINK-STATE-ID |self-originate | adv-router IP-ADDRESS] Syntax Description LINK-STATE-ID Link command CLI Reference Guide 664 - D-Link DGS-6600-48TS | CLI Guide - Page 675
E|-) LS Type: network-LSA Link State ID: 47.65.51.2 (address of Designated Router) Advertising Router: 10.47.65.181 LS Seq Number: 80000001 Checksum: 0x9ea1 Length: 32 Network Mask: /29 Attached Router: 10.47.65.181 Attached Router: 10.47.65.160 Total Entries: 2 Switch# CLI Reference Guide 665 - D-Link DGS-6600-48TS | CLI Guide - Page 676
DGS-6604 m show ip ospf database nssa-external show ip ospf database nssa-external Use this command to display information about the nssa-external LSAs. how ip ospf database nssa-external [LINK-STATE-ID | self-originate | adv-router IP-ADDRESS] Syntax Description LINK-STATE-ID Link Guide 666 - D-Link DGS-6600-48TS | CLI Guide - Page 677
DGS-6604 m show ip ospf database nssa-external Switch#show ip ospf database nssa-external NSSA-external Link States (Area 0.0.0.61 [NSSA]) LS age: 1161 Options: 0x0 LS Type: AS-NSSA-LSA Link 2 (Larger than any link state path) TOS: : AS-NSSA-LSA Link State ID: 47. than any link state path) - D-Link DGS-6600-48TS | CLI Guide - Page 678
DGS-6604 m show ip ospf database router show ip ospf database router Use this command to display information about the router LSAs. show ip ospf database router [LINK-STATE-ID | self-originate | adv-router IP-ADDRESS] Syntax Description LINK-STATE-ID Link command. CLI Reference Guide 668 - D-Link DGS-6600-48TS | CLI Guide - Page 679
DGS-6604 m Switch#show ip ospf database router Router Link States (Area 0.0.0.0) LS age: 1056 Options: 0x2 E|-) Flags: 0x3 : ABR ASBR LS Type: router-LSA Link State ID: 10.47.65.160 Advertising Router: 10.47.65.160 LS Seq Number: 8000000e Checksum: 0x107f Length: 96 Number of Links: 6 Link - D-Link DGS-6600-48TS | CLI Guide - Page 680
DGS-6604 m .Link connected to: a Virtual Link (Link ID) Neighboring Router ID: 10.47.65.184 (Link Data) Router Interface address: 47.65.54.1 Number of TOS metrics: 0 TOS 0 Metric: Link connected to: Stub Network (Link ID) Network/subnet number: 47.65.49.112 (Link Data) Network Mask: 255.255.255.255 - D-Link DGS-6600-48TS | CLI Guide - Page 681
DGS-6604 m show ip ospf database summary show ip ospf database summary Use this command to display information about the summary LSAs. how ip ospf database summary [LINK-STATE-ID | self-originate | adv-router IP-ADDRESS] Syntax Description LINK-STATE-ID Link command. CLI Reference Guide 671 - D-Link DGS-6600-48TS | CLI Guide - Page 682
DGS-6604 m Switch#show ip ospf database summary Summary Link States (Area 0.0.0.0) LS age: 1225 Options: 0x2 E|-) LS Type: summary-LSA Link State ID: 0 Metric: 1 LS age: 1225 Options: 0x2 E|-) LS Type: summary-LSA Link State ID: 2.1.2.0 (summary Network Number) Advertising Router: 10.47.65.160 LS - D-Link DGS-6600-48TS | CLI Guide - Page 683
DGS-6604 m show ip ospf host-route show ip ospf host-route Use this command to display host-route information for command: Switch# show ip ospf host-route Host IP AreaID Cost 10.3.3.3 0.0.0.5 2 10.3.3.4 0.0.0.1 3 20.3.3.3 0.0.0.25 58 Total Entries: 3 CLI Reference Guide 673 - D-Link DGS-6600-48TS | CLI Guide - Page 684
DGS-6604 m show ip ospf interface Use this command to display interface information for OSPF. show ip ospf interface [IFNAME] show ip ospf OSPF information for all interfaces will be displayed. The following example on the next page is a sample output of this command: CLI Reference Guide 674 - D-Link DGS-6600-48TS | CLI Guide - Page 685
DGS-6604 m show ip ospf interface Switch#show ip ospf interface vlan49 is up, line protocol is up Internet Address 47.65 11, Discarded 0 Current Authentication Type: md5 Authentication Key Configuration Authentication type: md5 message-digest-key 254 md5 80008001 Switch# CLI Reference Guide 675 - D-Link DGS-6600-48TS | CLI Guide - Page 686
DGS-6604 m show ip ospf neighbor show ip ospf neighbor Use this command to display information about the OSPF neighbors. show ip ospf is 0x02 E|-) Dead timer due in 0DT0H1M13S Neighbor is up for 0DT0H13M51S Crypt Sequence Number is 0 vlan49 Total Entries: 1 Switch# CLI Reference Guide 676 - D-Link DGS-6600-48TS | CLI Guide - Page 687
link information. show ip ospf virtual-links show ip ospf virtual-links Syntax None Default None Command Mode User EXEC Usage Guideline Use this command to display virtual link information. Example The following pages show sample outputs from the show ip ospf neighbor. CLI Reference Guide - D-Link DGS-6600-48TS | CLI Guide - Page 688
DGS-6604 m show ip ospf virtual-links Switch#show ip ospf virtual-links Virtual Link to router 10.47.65.181 is up Transit area 0.0.0.1 via interface vlan51 Local : md5 Authentication Key Configuration Authentication type: md5 message-digest-key 255 md5 1234567890123456 CLI Reference Guide 678 - D-Link DGS-6600-48TS | CLI Guide - Page 689
DGS-6604 m show ip pim Use this command to show the PIM global information. show ip pim Syntax None Default None Command Mode User Candidate vlan100, group-list: rp-cand, interval: 60, priority: 192 BSR Candidate vlan100, hash-mask-length: 30, priority: 1 show ip pim CLI Reference Guide 679 - D-Link DGS-6600-48TS | CLI Guide - Page 690
DGS-6604 m show ip pim bsr show ip pim bsr Use this command to show the bootstrap router (BSR) information. show ip show ip pim bsr PIMv2 Bootstrap information BSR address: 90.1.1.3 Uptime: 0DT0H0M38S, BSR Priority: 3, Hash mask length: 30 Expires: 0DT0H1M32S Switch# CLI Reference Guide 680 - D-Link DGS-6600-48TS | CLI Guide - Page 691
DGS-6604 m show ip pim interface Use this command to show the interface information. show ip pim interface [INTERFACE-ID] [ .1.1.1 vlan200 Dense 1 0 0.0.0.0 375693 Total Entries: 2 On the following page is an example which displays the interface information in detail. CLI Reference Guide 681 - D-Link DGS-6600-48TS | CLI Guide - Page 692
DGS-6604 m switch#show ip pim interface detail vlan100 Address : 90.1.1.1 Mode : Sparse Neighbor Count : 1 DR : 90.1.1.1 DR Retry Interval : 3 seconds State Refresh Priority Enabled : Enabled State Refresh Origination Interval: 60 seconds CLI Reference Guide show ip pim interface 682 - D-Link DGS-6600-48TS | CLI Guide - Page 693
DGS-6604 m show ip pim mroute This command displays the PIM IP multicast routing table show ip pim mroute show ip pim mroute Syntax (that is, through Reverse Path Forwarding [RPF]). Example The following page shows a sample output from the command show ip pim mroute. CLI Reference Guide 683 - D-Link DGS-6600-48TS | CLI Guide - Page 694
DGS-6604 m show ip pim mroute Switch#show ip pim mroute PT - Prune Timer, PPT - Prune Pending Timer, ET - Expiry Timer, PLT - Prune Limit Interface List: vlan200 JP State: No Info, PT: Off, PPT: off Assert State: No Info, AT: Off, Assert Winer: 0.0.0.0, Metric: 0, Pref: 0 CLI Reference Guide 684 - D-Link DGS-6600-48TS | CLI Guide - Page 695
DGS-6604 m show ip pim neighbor show ip pim neighbor Use this command to Descriptions Priority and mode of the designated router (DR). Priority: "N" indicates the neighbor does not support DR Priority Option in the Hello message otherwise the DR priority value will be displayed. Mode: Describes - D-Link DGS-6600-48TS | CLI Guide - Page 696
DGS-6604 m Field DR Pri/Mode show ip pim neighbor Descriptions B: bidirectional mode, neighbor is using the Bidirectional-PIM Capable option. DR: DR. S: State Refresh Capable. The neighbor is using the State Refresh Capable option. This option is used only by PIM-DM. CLI Reference Guide 686 - D-Link DGS-6600-48TS | CLI Guide - Page 697
DGS-6604 m show ip pim rp mapping show ip pim rp mapping Use this command to show group-to-RP (rendezvous point) mappings, and the RP about this RP expires. If the router does not receive any refresh messages in this time, it will discard information about this RP. CLI Reference Guide 687 - D-Link DGS-6600-48TS | CLI Guide - Page 698
DGS-6604 m show ip pim rp-hash show ip pim rp-hash Use this command to display the rendezvous point (RP) to be chosen based Uptime: 0DT1H42M15S, expires: 0DT0H2M16S Please refer to the table in the description of command show ip pim rp mapping for the field descriptions. CLI Reference Guide 688 - D-Link DGS-6600-48TS | CLI Guide - Page 699
DGS-6604 m show ip protocols show ip protocols Use this command to display the state of the dynamic routing process. show ip protocols [ 0 1 the maximum number of RIP routes allowed: 12288 Number of routes (excluding connected): 3 Distance: (default is 120) Switch# CLI Reference Guide 689 - D-Link DGS-6600-48TS | CLI Guide - Page 700
DGS-6604 m show ip protocols The table below describes the show ip protocols Field Descriptions for a RIP Process: Field Description Distance: (default is 110) Do not originate type 5 default route Redistributing: type metric mtric_type rip 20 2 Switch# CLI Reference Guide 690 - D-Link DGS-6600-48TS | CLI Guide - Page 701
DGS-6604 m show ip rip database show ip rip database To display summary address entries in the Routing Information Protocol (RIP) routing database entries, use and it was updated 16 seconds ago. The other source is 40.33.24.8 via vlan3, and it was updated 30 seconds ago. CLI Reference Guide 691 - D-Link DGS-6600-48TS | CLI Guide - Page 702
DGS-6604 m show ip rip interface Display interface specific information for RIP. show ip rip interface [INTERFACE-ID] show ip rip Authentication Mode: text Passive interface: Disabled Split horizon: Enabled with Poisoned Reversed IP interface address: 20.72.63.80/8 CLI Reference Guide 692 - D-Link DGS-6600-48TS | CLI Guide - Page 703
DGS-6604 m show ip route show ip route To display the current state of the routing table, use the show ip route command. show ip route , including active and inactive entries. Display all active static routes with both the show ip route and show ip route static commands. CLI Reference Guide 693 - D-Link DGS-6600-48TS | CLI Guide - Page 704
DGS-6604 m Examples Field O E2 * > 10.110.0.0 show ip route The following examples show the standard routing tables displayed by the show ip route entry of RIB is populated in FIB. The selected route of multiple route entries. Indicates the address of the remote network. CLI Reference Guide 694 - D-Link DGS-6600-48TS | CLI Guide - Page 705
DGS-6604 m Field [160/5] via 10.119.254.6 0DT0H0M44S Vlan2 Total Entries : show ip route Description The first number in the brackets is the 24 [20/0] via 10.50.71.200, vlan10, 0DT1H5M35S 160.0.0.0/8 [1/0] via 10.50.71.200, vlan10 Total Entries: 12 entries, 12 routes CLI Reference Guide 695 - D-Link DGS-6600-48TS | CLI Guide - Page 706
DGS-6604 m show ip route The following example shows output of the show ip route database command. Switch#show ip route database Codes: K - kernel, C - 10.50.71.200, vlan10, 0DT1H7M7S S *> 160.0.0.0/8 [1/0] via 10.50.71.200, vlan10 Total Entries: 13 entries, 13 routes CLI Reference Guide 696 - D-Link DGS-6600-48TS | CLI Guide - Page 707
DGS-6604 m show ip route summary show ip route summary To display the current state of the routing table, use the show ip maximum-paths is 6 IP routing table maximum-paths is 6 Route Source Networks connected 2 rip 1 bgp 2 Total 5 FIB 3 multi-path 0 CLI Reference Guide 697 - D-Link DGS-6600-48TS | CLI Guide - Page 708
DGS-6604 m show ip ssh Use this command to display the user SSH configuration setting. show to display the SSH configuration settings. Switch# show ip ssh SSH : Enabled SSH server mode : V2 Service port : 22 Authentication timeout : 120 Authentication retries : 3 Switch# CLI Reference - D-Link DGS-6600-48TS | CLI Guide - Page 709
DGS-6604 m show ip trusted-host show ip trusted-host Use this command to display the trusted host information on the device. show ip trusted-host Valid to Access 10.48.93.100 all access interfaces 10.51.17.1 snmp 10.52.95.90 http Total Entries : 3 Switch# CLI Reference Guide 699 - D-Link DGS-6600-48TS | CLI Guide - Page 710
DGS-6604 m show ipv6 dhcp show ipv6 dhcp This command is used to display DHCPv6 client configuration running information of interface(s). show for interface vlan1, when vlan1 is DHCPv6 client disabled: Switch > enable Switch # show ipv6 dhcp interface vlan1 Switch # CLI Reference Guide 700 - D-Link DGS-6600-48TS | CLI Guide - Page 711
DGS-6604 m show ipv6 dhcp The following example shows the DHCPv6 client for interface vlan1, when vlan1 is in the REQUEST state: Switch > enable ID: 0003 T1: 300 T2: 800 Prefer Lifetime: 3600 Valid Lifetime: 7200 Prefix: 3000:1:2::/48 IA expire: 299 Addr expire: 7199 CLI Reference Guide 701 - D-Link DGS-6600-48TS | CLI Guide - Page 712
DGS-6604 m show ipv6 dhcp The following example shows the DHCPv6 client for interface vlan1, when vlan1 is in the RENEW state: Switch > enable Switch IA Type: PD IA ID: 0003 T1: 300 T2: 800 Prefer Lifetime: 3600 Valid Lifetime: 7200 Prefix: 3000:1:2::/48 Addr expire: 3192 CLI Reference Guide 702 - D-Link DGS-6600-48TS | CLI Guide - Page 713
DGS-6604 m show ipv6 dhcp relay interface show ipv6 dhcp relay interface These commands are used to display DHCP relay information. enable Switch # show ipv6 dhcp relay interface vlan1 Listen interface name: vlan1 Sever Addsess FE80::2:3 Destination interface name: vlan2 CLI Reference Guide 703 - D-Link DGS-6600-48TS | CLI Guide - Page 714
DGS-6604 m show ipv6 general-prefix show ipv6 general-prefix This command is used to vlan1 Apply to interface: vlan3 ::3:3:3:3:3/64 vlan2 ::4:4:4:4:4/64 ::2:2:2:2:2/64 IPv6 prefix my-prefix Acquired via Manual configuration: 3ffe:1:1::/48 Apply to interface: vlan2 ::1:1:1:1:1/64 CLI Reference - D-Link DGS-6600-48TS | CLI Guide - Page 715
to display information for a specified general prefix named my-prefix: Switch > enable Switch # show ipv6 general-prefix my-prefix IPv6 prefix my-prefix Acquired via Manual configuration: 3ffe:1:1::/48 Apply to interface: vlan2 ::1:1:1:1:1/64 CLI Reference Guide 705 - D-Link DGS-6600-48TS | CLI Guide - Page 716
DGS-6604 m show ipv6 interface show ipv6 interface incidence: Switch > enable Switch # show ipv6 interface vlan1 vlan1 is down, IPv6 is disable link-local address is : fe80::a01:2ff:fe39:1 global unicast address is : 3ffe:501:ffff:100 autoconfig for addresses. Switch # CLI Reference Guide 706 - D-Link DGS-6600-48TS | CLI Guide - Page 717
DGS-6604 m show ipv6 interface brief show interface type, you see information for that specific interface. At current stage, the supporting interface type is VLAN. If you specify no optional arguments, you see information on up] 2010:311::1 (DAD check fail) Switch # CLI Reference Guide 707 - D-Link DGS-6600-48TS | CLI Guide - Page 718
DGS-6604 m show ipv6 neighbors show ipv6 neighbors This command is used to display the IPv6 neighbor information. show ipv6 to PROBE. PROBE - A reaching confirmation is actively sought by resending neighbor solicitation messages every RetransTimer, in milliseconds. CLI Reference Guide 708 - D-Link DGS-6600-48TS | CLI Guide - Page 719
DGS-6604 m show ipv6 ospf show ipv6 ospf To display general information about OSPF routing processes, use the show ipv6 ospf command. show ipv6 ospf command. Switch > enable Switch # show ipv6 ospf The output after executing this command is as follows on the next page. CLI Reference Guide 709 - D-Link DGS-6600-48TS | CLI Guide - Page 720
DGS-6604 m show ipv6 ospf Routing Process " area router LSA 1. Checksum Sum 0x26DD Number of external LSA 0. Checksum Sum 0x0000 Number of link LSA 3. Checksum Sum 0x15A79 Number of intra-area prefix LSA 5. Checksum Sum 0x34475 Number of of LSA 7. Checksum Sum 0x499DF CLI Reference Guide 710 - D-Link DGS-6600-48TS | CLI Guide - Page 721
DGS-6604 m show ipv6 ospf border-routers show ipv6 ospf border-routers To display the ABRs and ASBRs for the IPv6 OSPF process, null) Codes: i - Intra-area route, I - Inter-area route i 47.65.49.111 [1] is directly connected, vlan49, ABR, Area 0.0.0.0 Total Entries: 1 CLI Reference Guide 711 - D-Link DGS-6600-48TS | CLI Guide - Page 722
DGS-6604 m show ipv6 ospf database show ipv6 ospf database Display the database summary of the OSPF routing processes, use the show ipv6 ospf database command. show ipv6 ospf [PROCESS-ID] database [router | network | inter-prefix | inter-router | external | link a link-state database ) Link-LSA - D-Link DGS-6600-48TS | CLI Guide - Page 723
DGS-6604 m show ipv6 ospf interface vlan2 is up, line protocol is up Interface ID 1026 IPv6 Prefixes fe80::a01:2ff:fe36:2/64 (Link-Local Address) 3ffe:4::30/64 OSPFv3 Process (null), Area 0.0.0.1 (active) MTU 1500, Instance ID 10 LS-Ack received 8 sent 6, Discarded 00 CLI Reference Guide 713 - D-Link DGS-6600-48TS | CLI Guide - Page 724
DGS-6604 m show ipv6 ospf neighbor show ipv6 ospf neighbor To display IPv6 OSPF neighbor information on a per interface basis, use the Time Interface 10.76.37.3 1 Full/DR 0DT0H0M33S vlan2 10.76.37.3 1 Full/ - 0DT0H0M38S VLINK1 Total Entries: 2 Instance ID 0 0 CLI Reference Guide 714 - D-Link DGS-6600-48TS | CLI Guide - Page 725
DGS-6604 m show ipv6 ospf route show ipv6 ospf route To display the current contents of the 0.0.0.3 C 3ffe:4::/64 1 directly connected, vlan2, TransitArea 0.0.0.1 C 3ffe:4::30/128 0 directly connected, vlan2, TransitArea 0.0.0.1 Total Entries: 6 entries, 6 routes CLI Reference Guide 715 - D-Link DGS-6600-48TS | CLI Guide - Page 726
DGS-6604 m show ipv6 ospf virtual-links show ipv6 ospf virtual-links To display parameters and the current state of IPv6 OSPF virtual links, use the show ipv6 ospf virtual-links command. show ipv6 ospf [PROCESS-ID] virtual-links Hello due in 0DT0H0M2S Adajcency state Full CLI Reference Guide 716 - D-Link DGS-6600-48TS | CLI Guide - Page 727
DGS-6604 m show ipv6 protocols show ipv6 protocols To display the parameters and current state of the active IPv6 routing (default is 110) metric-type 2 metric 16777215 Redistributing: type metric metric_type connected auto 2 static auto 2 rip auto 2 CLI Reference Guide 717 - D-Link DGS-6600-48TS | CLI Guide - Page 728
DGS-6604 m show ipv6 protocols The following is sample output from the show ipv6 protocols rip command. Switch > enable Switch # show interface is not set Default redistribute metric is 1 Redistributing: connected static ospf Interface vlan51 vlan54 Routing for Networks: CLI Reference Guide 718 - D-Link DGS-6600-48TS | CLI Guide - Page 729
DGS-6604 m show ipv6 rip database show ipv6 rip database To display information about current IPv6 RIP processes, use the show ipv6 Time fe80::219:5bff:fef5:2cc1 vlan2 2 fe80::219:5bff:fef5:2cc1 vlan2 2 :: vlan3 1 :: vlan2 1 Total Entries: 4 entries, 4 routes CLI Reference Guide 719 - D-Link DGS-6600-48TS | CLI Guide - Page 730
DGS-6604 m show ipv6 rip interface show ipv6 rip interface To display the usability status of interfaces configured for IPv6 RIP, use Protocol: RIPng Passive interface: Disabled Split horizon: Enabled with Poisoned Reversed IPv6 interface address: fe80::a01:2ff:fe36:1/64 CLI Reference Guide 720 - D-Link DGS-6600-48TS | CLI Guide - Page 731
DGS . For more information about supported interface types, use the about the numbering syntax for supported interface types, use the When the system provides forwarding services for IPv6 traffic, it is traffic path is in the network. When project support "ipv6 unicast-routing long-prefix" command, - D-Link DGS-6600-48TS | CLI Guide - Page 732
DGS-6604 m Example show ipv6 route Use the show ipv6 route command to check what the active routing entries for IPv6 are. Switch > ::/64 [1/0] via fe80::250:baff:fe91:bb28, vlan111 *> [1/0] via fe80::a00:1ff:fe02:6, vlan10 Total Entries: 10 entries, 12 routes Switch# CLI Reference Guide 722 - D-Link DGS-6600-48TS | CLI Guide - Page 733
DGS-6604 m show ipv6 route summary show ipv6 route summary To display the current state of the IPv6 routing table, use the configured maximum-paths is 6 IPv6 routing table maximum-paths is 6 Route Source Networks connected 2 ripng 1 Total 3 FIB 3 multi-path 0 CLI Reference Guide 723 - D-Link DGS-6600-48TS | CLI Guide - Page 734
DGS-6604 m show ipv6 unicast-routing long-prefix status show ipv6 unicast-routing long-prefix status To display the current settings the ip6route-longprefix status command: Switch # show ipv6 unicast-routing long-prefix status State : Enabled Log : Disabled Switch # CLI Reference Guide 724 - D-Link DGS-6600-48TS | CLI Guide - Page 735
DGS-6604 m show loopback-detection show loopback-detection Use the command to show the current loopback detection control settings. show Interface LoopDetect State Result Time Left(sec) eth3.1 Enabled Normal eth3.8 Enabled Normal eth4.5 Enabled Loop 20 CLI Reference Guide 725 - D-Link DGS-6600-48TS | CLI Guide - Page 736
DGS-6604 m show loopback-detection This example shows current loopback detection setting for vlan-based mode. Switch# show loopback-detection Status Time Left(sec) eth3.1 Enabled Normal eth3.8 Enabled Normal eth4.5 Enabled Loop 20 Total Entries: 3 Switch# CLI Reference Guide 726 - D-Link DGS-6600-48TS | CLI Guide - Page 737
DGS-6604 m show logging show logging Use show logging to display the state of the system logging process and the contents of the standard system logging and the logging host table. The following page shows an example of the command show logging with the keyword host: CLI Reference Guide 727 - D-Link DGS-6600-48TS | CLI Guide - Page 738
12:12:04, 2010-08-14 Interface vlan99 is up 1 12:11:47, 2010-08-14 System is cold started DGS-6600:15#show logging buffer - 3 Total logs:401 Index Date Log Text 401 06:26:45, 1993-01-03 Successfully -13 System is rebooted by user admin, IP 0.0.0.0, via co nsole CLI Reference Guide 728 - D-Link DGS-6600-48TS | CLI Guide - Page 739
an example of using the START-INDEX and STOP-INDEX arguments with the show logging buffer command. DGS-6600:15(mgmt-if)# show logging buffer 250 260 Total logs:402 Index Date Log Text 260 is up 250 08:45:04, 2010-09-20 Interface vlan20 is up DGS-6600:15(mgmt-if)# CLI Reference Guide 729 - D-Link DGS-6600-48TS | CLI Guide - Page 740
DGS-6604 m show mac address-table show mac address-table Use the show mac address-table command to display: a specific MAC address, static entries, dynamic table address 00:02:4B:28:C4:82 Vlan Mac Address Type Ports 1 00-02-4b-28-c4-82 Static CPU Total Entries: 1 CLI Reference Guide 730 - D-Link DGS-6600-48TS | CLI Guide - Page 741
DGS-6604 m show mac address-table This is an example of output from the show mac address-table static command: Switch> show mac address-table static -table vlan 1 Vlan Mac Address Type Ports 1 00-02-4B-28-C4-82 Static CPU 1 00-03-40-11-22-33 Dynamic eth3.2 CLI Reference Guide 731 - D-Link DGS-6600-48TS | CLI Guide - Page 742
DGS-6604 m show mac address-table aging destination-hit show mac address-table aging destination-hit Use the show mac address-table aging destination-hit command: Switch> show mac address-table aging destination-hit Mac address-table aging destination-hit is enabled CLI Reference Guide 732 - D-Link DGS-6600-48TS | CLI Guide - Page 743
DGS-6604 m show mac address-table aging-time show mac address-table aging-time Use the show mac address-table aging-time command to display of output from the show mac address-table aging-time command: Switch> show mac address-table aging-time Aging Time is 300 seconds. CLI Reference Guide 733 - D-Link DGS-6600-48TS | CLI Guide - Page 744
DGS-6604 m show mgmt-if show mgmt-if Use this command to show the status of the management port, including user settings and link status. .1.1.1/8 IPv4 Default Gateway : 10.1.1.254 IPv6 Global Address : 6600::66/64 IPv6 Link-local Address : fe80::40b:ff:fe19:0/64 IPv6 Default Gateway : :: - D-Link DGS-6600-48TS | CLI Guide - Page 745
DGS-6604 m show monitor session show monitor session Use this command to show all or a specific port mirroring session. show monitor session [ Both : eth3.2-3.4 RX : eth3.5 TX : eth3.7 Switch# This example shows how to display all the created port mirroring sessions. CLI Reference Guide 735 - D-Link DGS-6600-48TS | CLI Guide - Page 746
DGS-6604 m Switch# show monitor session Session 1 Session type: local session Destination Port : eth1.1 Source Ports : Both : eth1.2-4 Session type: remote destination session source remote VLAN : VLAN 100 destination Ports : eth2.5 Switch# show monitor session CLI Reference Guide 736 - D-Link DGS-6600-48TS | CLI Guide - Page 747
DGS-6604 m show multicast filtering-mode show interface to display the filtering mode on (only VLAN interfaces are supported). Default Command Mode Usage Guideline Examples None User EXEC or any Mode --------- VLAN1 filter-unregistered Total Entries: 1 CLI Reference Guide 737 - D-Link DGS-6600-48TS | CLI Guide - Page 748
DGS-6604 m show policy-map Use this comprising any existing service policy map. The command show policy-map INTERFACE-ID displays the policy map configuration if the service policy has been attached interface eth3.1 Router(config-if)#service-policy policy1 Router(config-if)#end CLI Reference - D-Link DGS-6600-48TS | CLI Guide - Page 749
DGS-6604 m show policy-map The following sample output shows the contents of the policy map called policy1: Switch# show policy-map policy1 police tr-tcm cir 500000 bc 10000 pir 1000000 be 10000 exceed-action : setdscp-transmit 2 violate-action : drop Total Entries : 1 CLI Reference Guide 739 - D-Link DGS-6600-48TS | CLI Guide - Page 750
DGS-6604 m show port-security Use this command to display the current port security setting. displayed. This example shows how to display the port security setting of interface port eth4.1. DGS-6600:15#show port-security interface eth4.1 Interface Max No. Current No. Violation Secure Type State - D-Link DGS-6600-48TS | CLI Guide - Page 751
-saving Default None Command Mode User EXEC or any configuration mode Usage Guideline None Example The following example shows how to display power-saving information. DGS-6600:2#show power-saving Power-saving status phy power-saving:Enabled CLI Reference Guide 741 - D-Link DGS-6600-48TS | CLI Guide - Page 752
DGS-6604 m show qos aggregate-policer show qos aggregate-policer Use this command to display the configured aggregated policer. show qos aggregate-policer tr-tcm cir 64 bc 128 pir 256 be 512 exceed-action : set-dscp-transmit 2 violate-action : drop Total Entries:2 CLI Reference Guide 742 - D-Link DGS-6600-48TS | CLI Guide - Page 753
DGS-6604 m show qos interface show qos interface Use this command to display the port level QoS configurations. show qos interface > show qos interface eth3.2-3.5 cos Interface CoS eth3.2 3 (qos) eth3.3 4 (qos) eth3.4 4 (qos) eth3.5 3 (qos) Total Entries: 4 CLI Reference Guide 743 - D-Link DGS-6600-48TS | CLI Guide - Page 754
DGS-6604 m show qos interface This example displays the port trust state for ports eth3.2 - eth3.5. Switch> show qos interface eth3 > show qos interface eth3.1-3.2 dscp-mutation Interface DSCP Mutation Map eth3.1 Mutate Map 1 eth3.2 Mutate Map 2 Total Entries: 2 CLI Reference Guide 744 - D-Link DGS-6600-48TS | CLI Guide - Page 755
DGS-6604 m show qos interface The following example displays the CoS bandwidth allocation for ports eth3.13.2: Switch> show qos interface eth3.1-3.2 mapped to Green CoS 3-4 are mapped to Yellow CoS 6 are mapped to Red eth3.4 CoS 0-7 are mapped to Green Total Entries: 2 CLI Reference Guide 745 - D-Link DGS-6600-48TS | CLI Guide - Page 756
DGS-6604 m show qos interface The following example displays the DSCP to CoS map for ports eth3.1. Switch> show qos interface eth3.1 map dscp-cos eth3.1 0 1 2 3 4 5 6 7 8 9 05 05 05 05 05 06 06 50 06 06 06 06 06 06 07 07 07 07 60 07 07 07 07 CLI Reference Guide 746 - D-Link DGS-6600-48TS | CLI Guide - Page 757
DGS-6604 m show qos map show qos map Use this command to display the QoS DSCP mutation map configuration. show qos map dscp-mutation [MAP-NAME] 43 44 45 46 47 48 49 50 50 51 52 53 54 55 56 57 58 59 60 60 61 62 63 CLI Reference Guide 747 - D-Link DGS-6600-48TS | CLI Guide - Page 758
DGS-6604 m show route-map Use this command to display static route maps, show route-map [MAP-NAME] Syntax Description MAP-NAME (Optional) Name Switch# show route-map myPolicy route-map myPolicy, permit, sequence 10 Match clauses: as-path R1 Set clauses: weight 120 Switch# CLI Reference Guide 748 - D-Link DGS-6600-48TS | CLI Guide - Page 759
DGS-6604 m show running-config show running-config Use this command to display the contents of the configuration: version 1.00.001 #Slot Module-Type Model # 1 Management Control Module CMU-Card #2 - - #3 - - # 4 48 ports 1000Base-T 48T-IOCard ! ! ! CLI Reference Guide 749 - D-Link DGS-6600-48TS | CLI Guide - Page 760
DGS-6604 m show snmp Use this command to display the SNMP information of the device. show snmp {community | host | view | group | engineID} Syntax 100 v3 noauth 10.51.17.1 v2c public 20:64:84::154 v2c public SNMPv3 User Name initial Total Entries: 3 Switch# CLI Reference Guide 750 - D-Link DGS-6600-48TS | CLI Guide - Page 761
DGS-6604 m show snmp This example is sample output from the command show snmp view. Switch# show snmp view View Name : writeview: notifyview: *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF0F row status: active Total Entries: 4 Switch# CLI Reference Guide 751 - D-Link DGS-6600-48TS | CLI Guide - Page 762
DGS-6604 m show snmp This example is sample output from the command show snmp engineID. Switch# show snmp engineID Local SNMP engineID: 00000009020000000C025808 Switch# CLI Reference Guide 752 - D-Link DGS-6600-48TS | CLI Guide - Page 763
DGS-6604 m show snmp-server show snmp-server Use this command to display configuration information about the SNMP server. Trap State : Enabled SNMP Authentication : Enabled linkup : Enabled linkdown : Enabled coldstart : Enabled warmstart : Disabled Switch# CLI Reference Guide 753 - D-Link DGS-6600-48TS | CLI Guide - Page 764
DGS-6604 m show snmp user show snmp user Use this command to display information about the configured characteristics of an SNMP user. show NAME command. When the username argument is not entered, the show snmp user command displays information about all configured users. CLI Reference Guide 754 - D-Link DGS-6600-48TS | CLI Guide - Page 765
DGS-6604 m Example show snmp user This example shows how to display the SNMP user authuser's information. Switch# show snmp user authuser User Name: the SNMP group the user is a part of. • SNMP groups are defined in the context of a View-based Access Control Model (VACM). CLI Reference Guide 755 - D-Link DGS-6600-48TS | CLI Guide - Page 766
DGS-6604 m show sntp show sntp Syntax Default Command Mode Usage Guideline Example Use this command to show information about the SNTP server. None 171.69.118.9 5 172.21.28.34 4 Total Entries: 2. Switch> Last Receive 00:01:02 00:00:36 Synced show sntp CLI Reference Guide 756 - D-Link DGS-6600-48TS | CLI Guide - Page 767
DGS-6604 m show spanning-tree show spanning-tree This command is used to show the information about the STP module. This command is only for STP message will appear when the operating mode is MSTP. The example on the next page shows how to display the spanning information. CLI Reference Guide 757 - D-Link DGS-6600-48TS | CLI Guide - Page 768
DGS-6604 m show spanning- is configured as enabled Configured link type: A- Auto, P- point to point, S- shared Priority Link Interface Role State Cost . Configured Fast-Forwarding: Auto, Operation status : None-Edge Configured Link Type : Auto, Operation status: P2P Configured Path Cost : - D-Link DGS-6600-48TS | CLI Guide - Page 769
DGS-6604 m show spanning-tree mst show spanning-tree mst Use the command to show the information that used in MSTP version. show spanning-tree . An error message will appear if the operating mode is STP or RSTP. This example shows how to MSTP summary information. CLI Reference Guide 759 - D-Link DGS-6600-48TS | CLI Guide - Page 770
DGS-6604 m show spanning-tree mst Switch# show MST2 Designated Bridge: MST2 Topology changes count : 2 Remaining Hops : 19 Priority Link Interface Role State Cost .Port# Type Edge FA eth3.9 designated forwarding 20000 128.9 2000 128.12 p2p edge Switch# CLI Reference Guide 760 - D-Link DGS-6600-48TS | CLI Guide - Page 771
DGS-6604 m show spanning-tree mst This example shows how to display the MSTP MD5 digest information. Switch#show spanning-tree mst digest Name : [region1] Revision : 2, Instances configured: 3 Digest : 3C 60 DB F2 4B 03 EB F0 9C 59 22 F4 56 D1 8A 03 Switch# CLI Reference Guide 761 - D-Link DGS-6600-48TS | CLI Guide - Page 772
DGS-6604 m show ssh show ssh Syntax Default Command Mode Usage Guideline Example show ssh Use this command to display the status of Secure Shell ( is using. The login username that has been authenticated for the session. The IP address of the system running an SSH client. CLI Reference Guide 762 - D-Link DGS-6600-48TS | CLI Guide - Page 773
DGS-6604 m show startup-config show startup-config Use this command to display the content of the startup configuration file. show -config #Boot configuration file=flash:\configurations\def_usr.conf #Switch Chassis-based High-Speed Switch #Firmware Version:1.00.001 CLI Reference Guide 763 - D-Link DGS-6600-48TS | CLI Guide - Page 774
DGS-6604 m show storm-control show storm-control Use this command to show the current storm control settings. show storm-control [interface [INTERFACE- Drop pps 500 eth3.2 Broadcast Shutdown percentage 80 eth3.3 Broadcast Shutdown percentage 80 Total Entries:3 CLI Reference Guide 764 - D-Link DGS-6600-48TS | CLI Guide - Page 775
DGS-6604 m This example shows all the interface settings. show storm-control Switch# show storm-control interface Interface Storm Action settings. Switch# show storm-control Time Interval Countdown Timer Auto Recover Time : 15 seconds : 180 seconds : 300 seconds CLI Reference Guide 765 - D-Link DGS-6600-48TS | CLI Guide - Page 776
DGS-6604 m show system Use this unit. protocol-state (Optional) Shows the information about supporting protocols. Default Command Mode Usage Guideline Example None about the administrative and operational state of the supported protocols. This example on the following page shows how to - D-Link DGS-6600-48TS | CLI Guide - Page 777
00.018 :QT111AC000001 :DGS-6600-48TS :08:03:05:21:00:00 :48 Slot: 4 Hardware Version Bootloader Version Firmware Version S/N Model Name First MAC Address Number of MAC Address(es) :0A1G :1.00.002 :1.00.018 :QT0Z1AC000001 :DGS-6600-48S :06:48:c0:14:00:00 :48 show system CLI Reference Guide 767 - D-Link DGS-6600-48TS | CLI Guide - Page 778
DGS-6604 m show system The following shows the output for the command show system protocol-state command: CLI Reference Guide 768 - D-Link DGS-6600-48TS | CLI Guide - Page 779
DGS-6604 m DGS-6600:15#show system protocol-state Password Encryption :Disabled SNMP Server :Disabled SNMP6 Server :Disabled Sys Snooping :Disabled IP Source Guard :Disabled Dynamic ARP Inspection :Disabled Policy Base Route :Enabled DGS-6600:15# CLI Reference Guide show system 769 - D-Link DGS-6600-48TS | CLI Guide - Page 780
DGS-6604 m show time-range show time-range Use this command to display the time range profile configuration. show time-range [NAME] Syntax Description NAME (Optional) :00 ~ 23:59, every Sat 00:00 ~ 23:59, every Sun 19:00 (the 1st day) ~ 17:00 (the 2nd day) every month CLI Reference Guide 770 - D-Link DGS-6600-48TS | CLI Guide - Page 781
DGS-6604 m show traffic-segmentation show traffic-segmentation Use this command to show the traffic segmentation for some ports # show traffic-segmentation interface eth3.1 Interface Forwarding Interface(s) eth3.1 eth3.1, eth3.4, eth3.5, eth3.6 Total Entries: 1 CLI Reference Guide 771 - D-Link DGS-6600-48TS | CLI Guide - Page 782
differ depending on the SW release. Slot Model 1 DGS-6600-CM 2 3 4 DGS-6600-8XG Slot Model 1 DGS-6600-CM 2 3 4 DGS-6600-8XG Status Up-Time ok 0DT0H2M49S - - - display fields. Display Field up time Description The operating time since system power-up. CLI Reference Guide 772 - D-Link DGS-6600-48TS | CLI Guide - Page 783
DGS-6604 m show username show username Use this command to display the username and password pair database. show username [NAME] Syntax Description NAME the entry's password is encrypted. If there is no '*' next to the entry it indicates the password is 'Plain Text'. CLI Reference Guide 773 - D-Link DGS-6600-48TS | CLI Guide - Page 784
DGS-6604 m show user-session show user-session Use this command to display information about the active lines on the switch. show user-session [console | , 2008-05-13 0.0.0.0 co 15 12345678901234567890 1 01:00:28, 2008-05-13 172.171.160.100 te 15 admin Total Entries: 2 CLI Reference Guide 774 - D-Link DGS-6600-48TS | CLI Guide - Page 785
a DGS-6604 DGS-6600-CM Serial#: P4Z21A9000001 H/W: 0A1G Bootloader: 1.00.001 PCBA: 0 Runtime: 1.00.021 CPLD: ver-0 2 - - 3 - - 4 DGS-6600-48S Serial#: 123456789-123456789-123456789-0123456789 H/W: 0A1G Bootloader: 1.00.001 Runtime: 1.00.021 CPLD: ver-4 CLI Reference Guide - D-Link DGS-6600-48TS | CLI Guide - Page 786
DGS-6604 m show vlan show vlan Use the show VLAN command to display the parameters for all configured VLANs or one VLAN (if the show vlan interface command to show port-oriented VLAN information, such as, port PVID, ingress checking, and acceptable frame type information. CLI Reference Guide 776 - D-Link DGS-6600-48TS | CLI Guide - Page 787
DGS-6604 m Examples show vlan The following are the causes for an interface to become an un-tagged member port of a VLAN. 1. Configuration optional key word is specified all of VLAN configurations are displayed. This example shows how to display all current VLAN entries. CLI Reference Guide 777 - D-Link DGS-6600-48TS | CLI Guide - Page 788
DGS-6604 m Switch# show vlan VLAN 1: Name: default GVRP advertisement: yes Static Tag Member Ports: None Static Untag Member Ports: eth4.2, eth4.3, eth4 Static Untag Member Ports: eth4.43, GVRP Advertise Ports: eth4.1-eth4.48, port-channel1 Forbidden Ports: None show vlan CLI Reference Guide 778 - D-Link DGS-6600-48TS | CLI Guide - Page 789
DGS-6604 m show vlan This example shows how to display information for interface ports eth4.1 to eth4.3. Information State : Disabled Ingress checked : Enabled Access VLAN : 1 Advertise VLAN : 1-4094 Forbidden VLAN : Acceptable frame types : admit-all Switch# CLI Reference Guide 779 - D-Link DGS-6600-48TS | CLI Guide - Page 790
DGS-6604 m This example shows how to display the MAC-base VLAN table. Switch(config)#show vlan mac-base MAC Address base Subnet VLAN ID ---------- ------ 20.0.1.0/8 100 192.0.1.0/8 100 20.0.2.0/8 200 20.0.3.0/8 300 Total Entries: 4 Switch(config)# show vlan CLI Reference Guide 780 - D-Link DGS-6600-48TS | CLI Guide - Page 791
DGS-6604 m show vlan-tunnel Use this command to display the VLAN tunnel related settings. show vlan-tunnel [INTERFACE-ID [ , | - ] ] show vlan-tunnel interface(s) in the VLAN translation table. If no argument is specified only the status of VLAN tunnel mode will be shown. CLI Reference Guide 781 - D-Link DGS-6600-48TS | CLI Guide - Page 792
DGS-6604 m Examples show vlan-tunnel This example shows how to display the status of VLAN tunnel mode. Switch# show vlan-tunnel VLAN tunneling: above fields. Description The state of the VLAN tunneling function. Indicates that the port is either a UNI port or NNI port. CLI Reference Guide 782 - D-Link DGS-6600-48TS | CLI Guide - Page 793
DGS-6604 m Field CoS remarking VLAN S-VID/C-VID CoS show vlan-tunnel Description Indicates the CoS remarking status at the port. It could be either disabled or an integer from 0~7 (indicating the remarking CoS Value). Shows the VLAN encapsulation and remarking pairs. Indicates the service Guide 783 - D-Link DGS-6600-48TS | CLI Guide - Page 794
DGS-6604 m show vlan-tunnel ctag-mapping show vlan-tunnel ctag-mapping This command is used to display the state of the dynamically learned static Destination IP C-VID 192.168.10.0/24 233 192.168.20.0/24 155 2011:254::/64 850 Total Entries: 3 Switch# CLI Reference Guide 784 - D-Link DGS-6600-48TS | CLI Guide - Page 795
DGS-6604 m show vrrp This command is used to view the VRRP status. show vrrp [interface INTERFACE-ID [VRID]] show vrrp Syntax are 2 VRID, 7 and 8, configured in the interface vlan1, a VRID 5 configured in interface vlan2 and a VRID 1 configured in interface vlan3. CLI Reference Guide 785 - D-Link DGS-6600-48TS | CLI Guide - Page 796
DGS-6604 m Switch#show vrrp vlan1 - VRID 7 State is Master Virtual IP address is 20.0.1.1 Virtual MAC address is 00-00-5e-00-01- disabled Priority is 80 Critical IP address is 0.0.0.0 Master router is 50.0.1.2 Master Down interval is 3.687 sec (expires in 3.550 sec) CLI Reference Guide show vrrp 786 - D-Link DGS-6600-48TS | CLI Guide - Page 797
DGS-6604 m show vrrp The following example shows how to view VRRP information of interface vlan1 and VRID 8. Switch#show vrrp interface vlan1 8 Preemption disabled Priority is 200 Critical IP address is 0.0.0.0 Master router is 20.0.1.1 Master Down interval is 3.218 sec CLI Reference Guide 787 - D-Link DGS-6600-48TS | CLI Guide - Page 798
DGS-6604 m show vrrp brief This command is used to view the VRRP brief status. show vrrp brief [ all ] show vrrp brief Syntax Description all preempt mode is enabled. State of the virtual router IP address of the master virtual router. IP address of the virtual router. CLI Reference Guide 788 - D-Link DGS-6600-48TS | CLI Guide - Page 799
DGS-6604 m shutdown (interface) shutdown (interface) Use this command to disable the port , the port will set the port to the enabled state. When a port is shutdown (disabled), the link status will also be off. Below demonstrates using the shutdown command to set interface port eth3.1 to the - D-Link DGS-6600-48TS | CLI Guide - Page 800
DGS-6604 m shutdown (Management Port) shutdown (Management Port) Use this command to disable the management port. Use the no form of the command to the settings Switch(config)#mgmt-if Switch(mgmt-if)#shutdown Switch(mgmt-if)#end by entering the show mgmt-if command. CLI Reference Guide 790 - D-Link DGS-6600-48TS | CLI Guide - Page 801
DGS-6604 m show ip dhcp snooping Use this command to display DHCP snooping configuration. show ip dhcp snooping Syntax Not Applicable Verify MAC address is Enabled Information option: not allowed Interface Trusted eth3.1 no eth3.8 no eth3.9 yes Switch# CLI Reference Guide 791 - D-Link DGS-6600-48TS | CLI Guide - Page 802
DGS-6604 m show ip dhcp snooping binding show ip dhcp snooping binding Use the command to display DHCP snooping binding entries. show ip dhcp .1.1.10 eth3.5 1500 dhcp-snooping 100 00-01-02-00-00-05 10.1.1.1 eth3.5 1495 dhcp-snooping 100 Total Entries: 2 Switch# CLI Reference Guide 792 - D-Link DGS-6600-48TS | CLI Guide - Page 803
DGS-6604 m This example shows how to display DHCP snooping binding entries by IP 10.1.1.1: Switch# show ip dhcp snooping binding 10.1.1.1 Mac IP Address Lease(seconds) Type VLAN 00-01-02-00-00-05 10.1.1.1 eth3.5 1495 dhcp-snooping 100 Total Entry: 1 Switch# CLI Reference Guide 793 - D-Link DGS-6600-48TS | CLI Guide - Page 804
DGS-6604 m This example shows how to display DHCP snooping binding entries by IP 10.1.1.1 and MAC 00-01-02-03-04-05 on vlan100: Switch# 10.1.1.10 eth3.5 1500 dhcp-snooping 100 00-01-02-00-00-05 10.1.1.11 eth3.5 1495 dhcp-snooping 100 Total Entries: 2 Switch# CLI Reference Guide 794 - D-Link DGS-6600-48TS | CLI Guide - Page 805
DGS-6604 m show ip dhcp snooping database show ip dhcp snooping database This command is used to display snooping database Successful Transfer: 0 Failed Transfer : 0 Binding Collisions : 0 Expired lease : 0 Invalid interfaces : 0 Parse failures : 0 Switch# CLI Reference Guide 795 - D-Link DGS-6600-48TS | CLI Guide - Page 806
DGS-6604 m show erps domain show erps domain The show erps domain command is used to display information of all created ERPS domains Switch# show erps domain ERPS is globally disabled Switch# The following example displays instance information of all created ERPS domains: CLI Reference Guide 796 - D-Link DGS-6600-48TS | CLI Guide - Page 807
DGS-6604 m show erps domain Switch# show erps domain Domain ERPI Type Status Port-State ID campus1 1 Major Idle East: Blocked West:Forwarding campus1 2 Sub Protection East:Virtual Channel West:Forwarding Total ERP instances in domain campus1 : 2 Switch# CLI Reference Guide 797 - D-Link DGS-6600-48TS | CLI Guide - Page 808
DGS-6604 m show erps erpi show erps erpi The show erps erpi command is used to display information of ERP instance. show for disabled ERP instance, it will only display "configured" values of parameters. The following example displays detailed information ERP instance 1: CLI Reference Guide 798 - D-Link DGS-6600-48TS | CLI Guide - Page 809
DGS-6604 m show erps erpi Switch# show erps erpi 1 ERPS global state : Enabled ERP instance state : Blocked West ring port : eth3.2 West ring port state : Forwarding RPL owner port : East Service protected VLANs : 10-20 Guard timer : 500 milliseconds Hold-Off timer : 0 milliseconds WTR timer : 5 - D-Link DGS-6600-48TS | CLI Guide - Page 810
DGS-6604 m Switch# show erps erpi 2 ERPS global state : Enabled ring port : eth3.3 West ring port state : RPL owner port : (Not-configured) Service protected VLANs : 15-25 Guard Timer : 500 milliseconds Hold-Off Timer : 0 milliseconds WTR : Enabled Switch# show erps erpi CLI Reference Guide 800 - D-Link DGS-6600-48TS | CLI Guide - Page 811
DGS-6604 m show vlan voice-vlan Use this command to display the voice VLAN configurations. show vlan voice-vlan [oui | interface INTERFACE- Voice VLAN ID : 1000 CoS Priority : 7 Aging time : 60 minutes Member ports : eth3.1-3.5 Dynamic member ports : eth3.4 Switch# CLI Reference Guide 801 - D-Link DGS-6600-48TS | CLI Guide - Page 812
DGS-6604 m This example displays the OUI information of voice VLAN. Switch#show vlan .1-3.5 Interface eth3.1 eth3.2 eth3.3 eth3.4 eth3.5 Status ---------Enabled Enabled Enabled Enabled Enabled Mode -------Manual Manual Manual Manual Manual Total Entries: 5 Switch# CLI Reference Guide 802 - D-Link DGS-6600-48TS | CLI Guide - Page 813
DGS-6604 m This example displays the learned voice devices on ports eth3.1 and eth3.2. Switch#show vlan voice-vlan device interface eth3.1-3.2 Interface Port ID : 10.10.1.2 Create Time : 10:09:14, 2011-05-20 Remain Time : 120 Seconds Total Entries: 2 Switch# CLI Reference Guide 803 - D-Link DGS-6600-48TS | CLI Guide - Page 814
DGS-6604 m show ip policy show ip policy Use the command to display the route map used for policy based routing. show ip policy the show ip policy command: Switch#show ip policy Interface Route-map vlan1 pbr-map1 Vlan2 pbr-map2 Vlan100 pbr-map3 Switch# CLI Reference Guide 804 - D-Link DGS-6600-48TS | CLI Guide - Page 815
DGS-6604 m show ip arp inspection show ip arp inspection Use this command to display the status of DAI for a specific range 145261 145261 VLAN DHCP Permits Source MAC Failures 10 21546 0 VLAN Dest MAC Failures IP Validation Failures 10 0 0 Switch# CLI Reference Guide 805 - D-Link DGS-6600-48TS | CLI Guide - Page 816
DGS-6604 m show ip arp inspection This example shows how to display the statistics of packets that have been processed Source MAC Validation : Disabled Destination Mac Validation: Disabled IP Address Validation : Disabled VLAN Configuration 10 Enabled Switch# CLI Reference Guide 806 - D-Link DGS-6600-48TS | CLI Guide - Page 817
DGS-6604 m show ip arp inspection This example shows how to display the trust state of interface eth3.3: Switch# show eth3.1 untrusted eth3.2 untrusted eth3.3 untrusted eth3.5 Trusted eth3.6 untrusted eth3.7 untrusted eth3.8 untrusted Total Entries: 7 Switch# CLI Reference Guide 807 - D-Link DGS-6600-48TS | CLI Guide - Page 818
DGS-6604 m show ip source binding show ip source binding or any configuration mode IP source guard use binding entries that are either manually configured or auto learned by DHCP snooping. The command accepts combination of input binding entries by IP address 10.1.1.11. CLI Reference Guide 808 - D-Link DGS-6600-48TS | CLI Guide - Page 819
DGS-6604 m show ip source binding Switch# show ip source binding 10.1.1.11 MAC Address IP Address Lease(sec) Type VLAN Interface 00-01- Address Lease(sec) Type VLAN Interface 00-01-01-01-01-10 10.1.1.11 3564 dhcp-snooping 100 eth3.3 Total Entry: 1 Switch# CLI Reference Guide 809 - D-Link DGS-6600-48TS | CLI Guide - Page 820
DGS-6604 m show ip verify source show ip verify source Use this command to display the port ACL entry on a particular interface. show ip verify source [ -all MAC address VLAN 00-01-01-01-01-01 100 00-01-01-01-01-10 101 deny-all Total Entries: 3 Switch# CLI Reference Guide 810 - D-Link DGS-6600-48TS | CLI Guide - Page 821
DGS-6604 m show ip dhcp screening Used to display the configuration of DHCP server screening show ip dhcp screening show ip dhcp screening Syntax Server/Client List: Server IP Address Client MAC Address Port 10.1.1.1 00:08:01:02:03:04 eth4.1-4.23 Total Entries: 1 CLI Reference Guide 811 - D-Link DGS-6600-48TS | CLI Guide - Page 822
DGS-6604 m show sflow Use the show sflow command to display the sFlow information. show sflow sent to both 10.1.1.2 and 10.1.1.3: switch(config)# show sflow sFlow Agent Version: 1.3;D-Link Corporation;2.00 sFlow Agent Address: 10.1.1.1 sFlow State : Enabled Receivers Information Index : 1 - D-Link DGS-6600-48TS | CLI Guide - Page 823
DGS-6604 m show sflow Port Datagram Version : 6343 : 5 Index : 2 Owner : collector2 Current Countdown Time: 86355 Max Datagram Size : 2 2 512 256 Pollers Information Interface Instance Receiver Interval eth3.1 1 1 10 eth3.2 1 1 10 eth3.2 2 2 20 CLI Reference Guide 813 - D-Link DGS-6600-48TS | CLI Guide - Page 824
DGS-6604 m show lldp show lldp Syntax Default Command Mode Usage Guideline Example show lldp To displays the switch's general LLDP configuration, used to show LLDP system global configurations. This example shows how to display the LLDP system global configuration status: CLI Reference Guide 814 - D-Link DGS-6600-48TS | CLI Guide - Page 825
DGS-6604 m Switch> show lldp LLDP System Information Chassis ID Subtype : MAC Address Chassis ID : 00-33-50-43-00-00 System Name : Switch System Description : Stackable Ethernet Switch System Capabilities Supported -123456789-123456789-01 : D-Link Corporation. : DGS-6604 : XXXXXXXXXX : PSE - D-Link DGS-6600-48TS | CLI Guide - Page 826
DGS-6604 m show lldp interface show lldp interface To display the LLDP each physical interface configuration for advertisement options, use . The following is sample output from the show lldp interface command. To display a specific physical interface configuration: CLI Reference Guide 816 - D-Link DGS-6600-48TS | CLI Guide - Page 827
DGS-6604 m Switch> show lldp interface eth4.4 Port ID: eth4.4 Port ID : eth4.4 Admin Status Specific TLVs: MAC/PHY Configuration/Status : Disabled Power Via MDI : Disabled Link Aggregation : Disabled Maximum Frame Size : Disabled LLDP-MED Organizationally Specific TLVs: Capabilities - D-Link DGS-6600-48TS | CLI Guide - Page 828
DGS-6604 m show lldp local interface show lldp local interface To display the each physical interface information, which will be carried in is sample output from the show lldp local interface command to display outbound LLDP advertisements for eth4.4 in detailed mode.: CLI Reference Guide 818 - D-Link DGS-6600-48TS | CLI Guide - Page 829
DGS-6604 m show lldp local interface Switch> show lldp local interface eth4 Entry 1 : Port and Protocol VLAN ID PPVID Supported PPVID Enable : 2 : 4 : Supported : Enabled Entry 2 : Port and Protocol VLAN ID PPVID Supported PPVID Enable : 5 : Supported : Enabled VLAN Name Entries Count Entry 1 - D-Link DGS-6600-48TS | CLI Guide - Page 830
Power State PSE Pairs Control Ability PSE Power Pair Power Class : : PES : Supported : Enable : Uncontrollable : 0 : 2 Link Aggregation Aggregation Capability Aggregation Status Aggregation Port ID : Supported : Aggregated : Not Currently in Aggregation : 0 Maximum Frame Size : 1536 LLDP-MED - D-Link DGS-6600-48TS | CLI Guide - Page 831
DGS-6604 m show lldp local interface Inventory : Support Network Policy Application type VLAN ID Priority DSCP Unknown Tagged : : Voice : 100 : 7 : 0 : False : True Extended Power-Via-MDI Port ID : 06-48-D0-11-00-17 Port Description : RMON Port 1 on Unit 1 Switch> CLI Reference Guide 821 - D-Link DGS-6600-48TS | CLI Guide - Page 832
DGS-6604 m show lldp local interface Switch> show lldp local interface eth 3.1 Name Entries Count : 3 Protocol Identity Entries Count: 2 MAC/PHY Configuration Status : (See Detail) Link Aggregation : (See Detail) Maximum Frame Sixe : 1000 LLDP-MED capabilities Extended Poer via MDI Network - D-Link DGS-6600-48TS | CLI Guide - Page 833
DGS-6604 m show lldp management-address show lldp management-address To display the LLDP management address information, use the show .1.11 Advertising Ports : eth3.1-3.5, eth3.7, eth4.10-4.20 Switch> This example shows how to display all management address information: CLI Reference Guide 823 - D-Link DGS-6600-48TS | CLI Guide - Page 834
DGS-6604 m show lldp management-address Switch> show lldp management-address Address 1: (default) Subtype : IPv4 Address Subtype : IPv6 Address : :: IF Type : IfIndex OID : 1.3.6.1.4.1.171.10.118.3 Advertising Ports : eth3.6 Total Entries : 4 Switch> CLI Reference Guide 824 - D-Link DGS-6600-48TS | CLI Guide - Page 835
DGS-6604 m show lldp neighbor interface show lldp neighbor interface To display the each physical interface information currently learned from the Not applicable EXEC mode or any configuration mode This command display the information learned from the neighbor devices. CLI Reference Guide 825 - D-Link DGS-6600-48TS | CLI Guide - Page 836
DGS System Description : Stackable Ethernet Switch System Capabilities Supported : Repeater, Bridge System Capabilities Enabled : Protocol ID Entries Count : 0 (None) MAC/PHY Configuration/Status Power Via MDI Link Aggregation Maximum Frame Size Unknown TLVs Count (None) : (None) : (None) : - D-Link DGS-6600-48TS | CLI Guide - Page 837
DGS-6604 m LLDP-MED capabilities: LLDP-MED device class LLDP-MED capabilities support LLDP Inventory Management Switch> show lldp neighbor interface : Endpoint device class III : : Support : Support : Not Support : Support : Support : : Enabled : Enabled : Enabled : Enabled : Enabled : : PD device - D-Link DGS-6600-48TS | CLI Guide - Page 838
DGS-6604 m show System Description : Stackable Ethernet Switch System Capabilities Supported : Repeater, Bridge System Capabilities Enabled : Repeater Configuration Status : (See Detail) Power Via MDI : (See Detail) Link Aggregation : (See Detail) Maximum Frame Size : 1536 LLDP-MED - D-Link DGS-6600-48TS | CLI Guide - Page 839
DGS-6604 System Description : Stackable Ethernet Switch System Capabilities Supported : Repeater, Bridge System Capabilities Enabled : Repeater Configuration Status : (See Detail) Power Via MDI : (See Detail) Link Aggregation : (See Detail) Maximum Frame Size : 1536 LLDP-MED Guide 829 - D-Link DGS-6600-48TS | CLI Guide - Page 840
DGS-6604 m show lldp neighbor interface Switch > show lldp neighbor interface eth3.1-3.2 brief Port ID: eth3.1 Remote Entities Count : 3 Entity 1 Chassis ID ID Port Description : MAC Address : 00-01-02-03-04-05 : Local : eth3.2 : RMON Port 2 on Unit 3 Switch> CLI Reference Guide 830 - D-Link DGS-6600-48TS | CLI Guide - Page 841
DGS-6604 m show lldp statistics show lldp statistics To display the system global LLDP statistics information, use the show statistics Last Change Time : 0DT0H2M24S Total Inserts : 1 Total Deletes : 0 Total Drops : 0 Total Ageouts : 0 Interface PoE interface CLI Reference Guide 831 - D-Link DGS-6600-48TS | CLI Guide - Page 842
DGS-6604 m show lldp statistics interface show lldp statistics interface To display the each physical interface LLDP statistics : 27 Total Discards : 0 Total Errors : 0 Total Receives : 27 Total TLV Discards : 0 Total TLV Unknows : 0 Total Ageouts : 0 Switch> CLI Reference Guide 832 - D-Link DGS-6600-48TS | CLI Guide - Page 843
DGS-6604 m show poe power system are PoE capable, only the PoE capable units are displayed. The delim sign for specifying unit list supports two choices: hyphen (-) or comma (,). The hyphen sign is used for displaying continuous units such power system's power information. CLI Reference Guide 833 - D-Link DGS-6600-48TS | CLI Guide - Page 844
DGS-6604 m Switch# show poe power system power-info PoE system power budget: 2400 Watts(Total) PoE system notification: enabled PoE system service policy: preemptive unit priority allocated(W) 0(update done) 0(saved) 4 48 E101 4.0.1.2 1(process update) 0(saved) CLI Reference Guide 834 - D-Link DGS-6600-48TS | CLI Guide - Page 845
DGS-6604 m show poe power-inline show poe power- and "ethxx-y.y" for an interface range. If no interface is specified, all supported PoE interfaces are displayed. status Display the port configuration status. statistic Display the port poe power-inline status command. CLI Reference Guide 835 - D-Link DGS-6600-48TS | CLI Guide - Page 846
DGS-6604 m show poe power-inline switch# show poe power inline status Interface 2 1 0 3 0 ... 4.1 2 0 0 2 0 4.2 2 0 0 1 0 4.3 2 0 0 5 0 4.4 2 0 0 0 0 ... This is an example of output from the show poe power-inline measurement command. CLI Reference Guide 836 - D-Link DGS-6600-48TS | CLI Guide - Page 847
DGS-6604 m switch# show poe power inline measurement Interface Voltage(V) Current(mA) Temp(C) 3.1 54.2 109.2 35 3.2 55 196.1 38 ... 286.2 36 4.3 n/a n/a n/a 4.4 n/a n/a n/a ... Power(W) -------- 5.9 10.8 10.7 15.7 n/a n/a show poe power-inline CLI Reference Guide 837 - D-Link DGS-6600-48TS | CLI Guide - Page 848
DGS-6604 m ssh ssh To start an encrypted session with If you do not specify the -c keyword, during negotiation, the remote networking device sends all the supported crypto algorithms. (Optional) The TCP port number. TCP ports are numbered between 1 and 65535. to long in. CLI Reference Guide 838 - D-Link DGS-6600-48TS | CLI Guide - Page 849
DGS-6604 m ssh Switch# ssh -l admin 20.74.19.200 [email protected]'s password: Chassis-based High-Speed Switch Command Line Interface Firmware: 2.10.001 Copyright (c) 2007 D-Link Firmware: 2.10.001 Copyright (c) 2007 D-Link Corporation. All rights reserved. Switch# CLI Reference Guide 839 - D-Link DGS-6600-48TS | CLI Guide - Page 850
DGS-6604 m switchport voice-vlan state switchport voice-vlan state Use the command to configure the voice VLAN state of ports. switchport voice-vlan enable Switch(config-if)#end Switch# You can verify your settings by entering show vlan voice-vlan interface command. CLI Reference Guide 840 - D-Link DGS-6600-48TS | CLI Guide - Page 851
DGS-6604 m snmp-server snSn mp-server To enable the Simple Network Management Protocol (SNMP) agent, use the snmp-server command. To disable the the SNMP server. Switch(config)# no snmp-server Switch(config)# Verify the settings by entering the show snmp-server command. CLI Reference Guide 841 - D-Link DGS-6600-48TS | CLI Guide - Page 852
DGS-6604 m snmp-server community snmp-server community Use this command to set up the community access string to provide access to SNMP. Use to set the read/write community string to comaccess in the mib2 view. Switch(config)# snmp-server community comaccess view mib2 rw CLI Reference Guide 842 - D-Link DGS-6600-48TS | CLI Guide - Page 853
DGS-6604 m snmp-server community This example shows how to remove the community comaccess. . Switch(config)# no snmp-server community comaccess Verify the settings by entering the show snmp community command. CLI Reference Guide 843 - D-Link DGS-6600-48TS | CLI Guide - Page 854
DGS-6604 m snmp-server contact snmp-server contact Use this command to configure the system's snmp contact information. Use the no form of Department II. Switch(config)# snmp-server contact MIS Department II Verify the settings by entering the show snmp-server command. CLI Reference Guide 844 - D-Link DGS-6600-48TS | CLI Guide - Page 855
DGS-6604 m snmp-server enable traps snmp-server enable traps To enable all Simple Network Management Protocol (SNMP) notification types that are host command. This example shows how to enable the SNMP traps. Switch(config)# snmp-server enable traps Switch(config)# CLI Reference Guide 845 - D-Link DGS-6600-48TS | CLI Guide - Page 856
DGS-6604 m snmp-server enable traps snmp snmp- linkup(3) trap signifies that the sending device recognizes that one of the communication links, represented in the agent's configuration, has come up. linkdown (Optional) Controls command, both the snmp-server enable traps CLI Reference Guide 846 - D-Link DGS-6600-48TS | CLI Guide - Page 857
DGS-6604 m Examples snmp-server enable traps snmp these traps globally, disable these traps on specific interfaces using the no snmp trap link-status command in interface configuration mode. Note that in the interface level, linkUp and the show snmp-server traps command. CLI Reference Guide 847 - D-Link DGS-6600-48TS | CLI Guide - Page 858
DGS-6604 m snmp-server engineID local snmp-server the switch. For further details on the SNMP engine ID, see RFC 3411. To specify a manually configured ID, note that it is not necessary to specify the entire 24-character engine ID if entering the show snmp engineID command. CLI Reference Guide 848 - D-Link DGS-6600-48TS | CLI Guide - Page 859
DGS-6604 m snmp-server group snmp-server group Use VIEW write WRITE-VIEW notify NOTIFY-VIEW SMNPv3 is the most secure of the supported security models, as it allow explicit configuration of the authentication characteristics. Specifies authentication at privilege level 15. CLI Reference Guide 849 - D-Link DGS-6600-48TS | CLI Guide - Page 860
DGS-6604 m Usage Guideline Examples snmp-server group An SNMP group defines the access method, the read view, the write view, and the )# snmp-server group guestgroup v3 auth read interfacesMibView Switch(config)# Verify the settings by entering the show snmp group command. CLI Reference Guide 850 - D-Link DGS-6600-48TS | CLI Guide - Page 861
DGS-6604 m snmp-server host snmp-server host Use is general string that does not allow space. vlan-interface When input IP-ADDRESS is IPv6 link-local address, user must choose an existing vlan-interface to specify output interface for a -TRAP-PDU with the SNMPv3 header. CLI Reference Guide 851 - D-Link DGS-6600-48TS | CLI Guide - Page 862
DGS-6604 m Example how to set up the trap recipient for IPv6 link-local address as fe80::64:84:154 by using version 2 with security level. The community string: public and this link-local address will be specifies output the vlan-interface: vlan1. Switch( - D-Link DGS-6600-48TS | CLI Guide - Page 863
DGS-6604 m snmp-server location snmp-server location Use this command to configure the system location information. Use the no snmp-server location string HQ 15F. Switch(config)# snmp-server location HQ 15F Verify the settings by entering the show snmp-server command. CLI Reference Guide 853 - D-Link DGS-6600-48TS | CLI Guide - Page 864
DGS-6604 m snmp-server user snmp-server user Use this command to configure a new Simple Network Management Protocol (SNMP) user. Use the no Command Mode There is one pre-configured user: USER-NAME: initial GROUP-NAME: initial Global configuration with privilege level 15 CLI Reference Guide 854 - D-Link DGS-6600-48TS | CLI Guide - Page 865
DGS-6604 m Usage Guideline Examples snmp-server for security. If a password is forgotten, it cannot be recovered and it and will need to manually reconfigured. Either a plain-text password or a localized message digest 5 (MD5) digest can be specified show snmp user command. CLI Reference Guide 855 - D-Link DGS-6600-48TS | CLI Guide - Page 866
DGS-6604 m snmp-server view snmp-server view Use this command to create or update a view entry for SNMP. And use the no snmp-server view for the MIB object trees. The view needs to be specified when the snmp-server group command is used to define a user group. CLI Reference Guide 856 - D-Link DGS-6600-48TS | CLI Guide - Page 867
DGS-6604 m Example snmp-server view This example shows how to set a MIB view to interfacesMibView. Switch(config)#snmp-server view interfacesMibView group guestgroup v3 auth read interfacesMibView Switch(config)# Verify the settings by entering the show snmp view command. CLI Reference Guide 857 - D-Link DGS-6600-48TS | CLI Guide - Page 868
DGS-6604 m sntp server sntp server Use this SNTP can only receive the time from NTP servers; it cannot be used to provide time services to other systems. SNTP typically provides time within100 milliseconds of a precise time source, but it the show sntp server command. CLI Reference Guide 858 - D-Link DGS-6600-48TS | CLI Guide - Page 869
DGS-6604 m spanning-tree ( Global configuration ) spanning-tree ( Global configuration ) Use this command to enable STP mode. Use the no form the default mode. Switch(config)# spanning-tree Switch(config)# Verify the settings by entering the show spanning-tree command. CLI Reference Guide 859 - D-Link DGS-6600-48TS | CLI Guide - Page 870
DGS-6604 m spanning-tree (Interface configuration) spanning-tree (Interface configuration) This setting is used to configure the STP function on interface eth3.7 Switch(config-if)# spanning-tree Verify the settings by entering the show spanning-tree interface command. CLI Reference Guide 860 - D-Link DGS-6600-48TS | CLI Guide - Page 871
DGS-6604 m spanning-tree (timers) spanning-tree (timers) Use this command to set the value of Spanning-Tree Timers. It is only used for spanning-tree forward-time 16 Switch(config)# spanning-tree max-age 21 Verify the settings by entering the show spanning-tree command. CLI Reference Guide 861 - D-Link DGS-6600-48TS | CLI Guide - Page 872
DGS-6604 m spanning-tree cost spanning-tree cost This setting is used to configure the value of port path-cost on the specified config)#interface eth3.7 Switch(config-if)#spanning-tree cost 20000 Verify the settings by entering the show spanning-tree interface command. CLI Reference Guide 862 - D-Link DGS-6600-48TS | CLI Guide - Page 873
DGS-6604 m spanning-tree fast-forwarding spanning-tree fast-forwarding To enable fast forwarding mode, use the spanning-tree fast-forwarding eth3.7 Switch(config-if)#spanning-tree fast-forwarding Verify the settings by entering the show spanning-tree interface command. CLI Reference Guide 863 - D-Link DGS-6600-48TS | CLI Guide - Page 874
DGS-6604 m spanning-tree guard root spanning-tree guard (physical port and port-channel interfaces) This feature is used in a service-provider environment where the network administrator needs to prevent a low speed port entering the show spanning-tree interface command. CLI Reference Guide 864 - D-Link DGS-6600-48TS | CLI Guide - Page 875
DGS-6604 m spanning-tree link-type spanning-tree link-type To configure a link type for a port, use the spanning-tree link-type command. To return to the default settings, use the no form of this command. spanning-tree link-type {point-to-point | shared} no spanning-tree link-type Syntax - D-Link DGS-6600-48TS | CLI Guide - Page 876
DGS-6604 m spanning-tree mode spanning-tree mode Use this command to decide the STP mode. To return to the default settings, use the no version of STP module to RSTP. Switch(config)# spanning-tree mode rstp Verify the settings by entering the show spanning-tree command. CLI Reference Guide 866 - D-Link DGS-6600-48TS | CLI Guide - Page 877
DGS-6604 m spanning-tree mst (cost | port-priority) -ID MSTP instance identifier; valid values are from 0 to 63, the number of supported MSTP instances is project dependent. Instance 0 represents the default instance, CIST. cost COST spanning-tree mst 0 port-priority 64 CLI Reference Guide 867 - D-Link DGS-6600-48TS | CLI Guide - Page 878
DGS-6604 m spanning-tree mst (forward | max-age | max-hops) spanning-tree mst (forward | max-age | max-hops) Use this command to configure the forward-time 14 Switch(config)#spanning-tree mst max-age 19 Switch(config)#spanning-tree mst max-hops 19 Switch(config)# end CLI Reference Guide 868 - D-Link DGS-6600-48TS | CLI Guide - Page 879
DGS-6604 m spanning-tree mst configuration spanning-tree Changing an MST-configuration submode parameter can cause connectivity loss. To reduce service disruptions, when entering the MST-configuration submode, make changes first to a -tree mst configuration Switch(config)# CLI Reference Guide 869 - D-Link DGS-6600-48TS | CLI Guide - Page 880
DGS-6604 m spanning-tree mst hello-time spanning-tree mst hello-time Use this command to configure the per port hello time used in MSTP eth2.1 Switch(config-if)#spanning-tree mst hello-time 1 Verify the settings by entering the show spanning-tree mst interface command. CLI Reference Guide 870 - D-Link DGS-6600-48TS | CLI Guide - Page 881
DGS-6604 m spanning-tree mst priority Default Command Mode Usage Guideline Example PRIORITY: 32768 Global configuration The number of supported MSTP instances is project dependent. This priority has same definition as the "spanning- the show spanning-tree mst command. CLI Reference Guide 871 - D-Link DGS-6600-48TS | CLI Guide - Page 882
DGS-6604 m spanning-tree port-priority spanning-tree port-priority This setting is used to configure the value of the STP port priority eth3.7 Switch(config-if)#spanning-tree port-priority 0 Verify the settings by entering the show spanning-tree interface command. CLI Reference Guide 872 - D-Link DGS-6600-48TS | CLI Guide - Page 883
DGS-6604 m spanning-tree priority spanning-tree priority This command configures the bridge priority and is only used for RSTP and STP versions priority to 4096. Switch(config)# spanning-tree priority 4096 Verify the settings by entering the show spanning-tree command CLI Reference Guide 873 - D-Link DGS-6600-48TS | CLI Guide - Page 884
DGS-6604 m spanning-tree tcnfilter spanning-tree tcnfilter To enable Topology Change Notification (TCN) filtering at the specific interface, use eth3.7 Switch(config-if)#spanning-tree tcnfilter Verify the settings by entering the show spanning-tree interface command. CLI Reference Guide 874 - D-Link DGS-6600-48TS | CLI Guide - Page 885
DGS-6604 m spanning-tree transmit hold-count spanning-tree transmit hold-count This setting is used to limit the maximum BPDU transmission -count value. Switch(config)# spanning-tree transmit-hold-count 5 Verify the settings by entering the show spanning-tree command. CLI Reference Guide 875 - D-Link DGS-6600-48TS | CLI Guide - Page 886
DGS Manually sets a copper port to be the slave port. Specifies to determine the speed through auto-negotiation with its linked partner. • copper port: Specify to determine the speed via auto-negotiation with its linked If the specified speed is not supported by the hardware, an error Guide 876 - D-Link DGS-6600-48TS | CLI Guide - Page 887
DGS-6604 m Example speed duplex is set to auto auto-negotiation for 1000Base-T, setting it to enable is recommended to prevent an unexpected link status. For combo port interfaces, the user must assign the medium type for the settings by entering the show interface command. CLI Reference Guide 877 - D-Link DGS-6600-48TS | CLI Guide - Page 888
DGS-6604 m storm-control (Interface) storm-control (Interface) Use this command to configure the device to prevent storm attacks on a LAN. There eth3.1 Switch(config-if)# no storm-control broadcast Verify the settings by entering the show storm-control interface command. CLI Reference Guide 878 - D-Link DGS-6600-48TS | CLI Guide - Page 889
DGS-6604 m storm-control action (Interface) storm- to identify unknown unicast (DLF) storm events due to the hardware chip being unable support this function. Therefore, if unknown unicast packets exceed the set level, they will always .1 Broadcast shutdown pps 131072 CLI Reference Guide 879 - D-Link DGS-6600-48TS | CLI Guide - Page 890
DGS-6604 m storm-control action (Interface) This example shows how to configure Broadcast storm control action and level. It assigns the .1 Switch(config-if)# no storm-control broadcast action Verify the settings by entering the show storm-control interface command. CLI Reference Guide 880 - D-Link DGS-6600-48TS | CLI Guide - Page 891
DGS-6604 m storm-control level (Interface) storm-control level (Interface) This command configures the rising threshold for Storm Control 500 Switch# show storm-control interface broadcast Interface Storm Action Type Threshold eth3.1 Broadcast Drop pps 500 CLI Reference Guide 881 - D-Link DGS-6600-48TS | CLI Guide - Page 892
DGS-6604 m storm-control level (Interface) This example shows how to configure the Broadcast storm control LEVEL by percentage mode. It Type Threshold eth3.1 Broadcast Drop pps 131072 Verify the settings by entering the show storm-control interface command CLI Reference Guide 882 - D-Link DGS-6600-48TS | CLI Guide - Page 893
DGS-6604 m storm-control timer (Global) storm-control timer the port will enter into shutdown forever mode (i.e. the port is disabled and the status is link-down). When a port is in "shutdown mode", before the port enters into shutdown forever mode Otherwise, the port will CLI Reference Guide 883 - D-Link DGS-6600-48TS | CLI Guide - Page 894
DGS-6604 m Examples storm-control timer (Global) not be automatically recovered but it can be manually recovered by using the "no shutdown" command. This example shows how to configure the time Switch(config)# Verify the settings by entering the show storm-control command CLI Reference Guide 884 - D-Link DGS-6600-48TS | CLI Guide - Page 895
DGS-6604 m subnet-base (VLAN) subnet-base (VLAN) Use the subnet command to specify a subnet-based VLAN ID assignment for untagged incoming .0.1.0/8 Switch(config-vlan)#subnet-base 192.0.1.0/8 Switch(config-vlan)#end Verify the settings by entering the show vlan command. CLI Reference Guide 885 - D-Link DGS-6600-48TS | CLI Guide - Page 896
DGS-6604 m subnet-mask subnet-mask Use this command to configure the subnet mask for a DHCP address pool of the DHCP Server. Use 's subnet mask . switch#configure terminal switch(config)#ip dhcp pool pool1 switch(config-dhcp)#subnet-mask 255.0.0.0 switch(config-dhcp)# CLI Reference Guide 886 - D-Link DGS-6600-48TS | CLI Guide - Page 897
DGS-6604 m switchport port-security switchport port- defines that all learnt MAC addresses will not be purged unless a user deletes those entries manually. delete-on-timeout: Setting this mode defines that all learnt MAC addresses will be and restored after a reboot. CLI Reference Guide 887 - D-Link DGS-6600-48TS | CLI Guide - Page 898
DGS-6604 m switchport port- addresses are dropped until they have a sufficient number of secure MAC addresses manually removed. • Shutdown - The interface is error disabled when a security , it can be manually reenabled by entering no shutdown commands in interface-configuration mode CLI Reference - D-Link DGS-6600-48TS | CLI Guide - Page 899
DGS-6604 m Examples switchport port-security The no form of the command can be used in global configuration so that one command can -if)# switchport port-security violation protect Switch(config-if-range)# end Verify the settings by entering the show port-security command CLI Reference Guide 889 - D-Link DGS-6600-48TS | CLI Guide - Page 900
DGS-6604 m synchronization synchronization To enable the synchronization between Border Gateway Protocol (BGP) and an external Interior Gateway Protocol ( in AS 65121. Switch(config)# router bgp 65121 Switch(config-router)# synchronization Switch(config-router)# CLI Reference Guide 890 - D-Link DGS-6600-48TS | CLI Guide - Page 901
DGS-6604 m system-name system-name Use this command to configure the system name information. Use the no system-name command to set Stackable switch. Switch(config)# system-name DES-XXXXS Stackable Switch Verify the settings by entering the show snmp-server command. CLI Reference Guide 891 - D-Link DGS-6600-48TS | CLI Guide - Page 902
DGS-6604 m telnet teTlnet The telnet command is used to login in another device that supports Telnet software supports special Telnet commands commands will be displayed as follows: Supported commands are: e - terminate the current client software concurrently supported. Use "ctrl-c" to - D-Link DGS-6600-48TS | CLI Guide - Page 903
DGS-6604 m Examples telnet The following example shows how to telnet to the IP address 20.74. is 'Ctrl-_'. Telnet connecting ... Chassis-based High-Speed Switch Command Line Interface Firmware: 2.10.001 Copyright (c) 2010 D-Link Corporation. All rights reserved. Switch> CLI Reference Guide 893 - D-Link DGS-6600-48TS | CLI Guide - Page 904
DGS-6604 m telnet The following example shows a telnet session attempting to connect to -Speed Switch Command Line Interface Firmware: 2.10.001 Copyright (c) 2010 D-Link Corporation. All rights reserved. Switch> Supported commands are: e - terminate the current Telnet session If other key - D-Link DGS-6600-48TS | CLI Guide - Page 905
DGS-6604 m telnet The following example show how to telnet to the IP address 20 High-Speed Switch Command Line Interface Firmware: 2.10.001 Copyright (c) 2010 D-Link Corporation. All rights reserved. Switch> Supported commands are: e - terminate the current Telnet session If other key is - D-Link DGS-6600-48TS | CLI Guide - Page 906
DGS-6604 m telnet Interface Firmware: 2.10.001 Copyright (c) 2010 D-Link Corporation. All rights reserved. Switch> Supported commands are: e - terminate the current Telnet Interface Firmware: 2.10.001 Copyright (c) 2010 D-Link Corporation. All rights reserved. Switch> CLI Reference Guide 896 - D-Link DGS-6600-48TS | CLI Guide - Page 907
DGS-6604 m terminal length terminal length This command configures the number of lines to be displayed in the monitor output. The terminal length command mode only. This example shows how to change the lines to be displayed in a screen to 60. Switch# terminal length 60 CLI Reference Guide 897 - D-Link DGS-6600-48TS | CLI Guide - Page 908
DGS-6604 m terminal timeout terminal timeout Use this command to setup a timeout value, which upon its expiry, will autologout the terminal session. session to never timeout. Switch# terminal timeout never Verify the settings by entering the show running-config command. CLI Reference Guide 898 - D-Link DGS-6600-48TS | CLI Guide - Page 909
DGS-6604 m terminal width terminal width This command sets the number of character columns on the terminal screen for the current lines displayed in affected by the change. That is because the adjustment is only applied to the current session. Switch#terminal width 120 CLI Reference Guide 899 - D-Link DGS-6600-48TS | CLI Guide - Page 910
DGS-6604 m terminal width The following example shows how to adjust the terminal session width to 120 as the system configuration setting for terminal width. This setting will affect all subsequently opened terminal sessions. Switch#terminal width 120 default CLI Reference Guide 900 - D-Link DGS-6600-48TS | CLI Guide - Page 911
DGS-6604 m timers timers Use this command to configure the RIP network timers. To restore the default timers use the default form of terminal Switch(config)# router rip Switch(config-router)# timer update 60 Verify the settings by entering the show ip protocols command. CLI Reference Guide 901 - D-Link DGS-6600-48TS | CLI Guide - Page 912
DGS-6604 m timers basic timers basic To configure update, timeout, and garbage-collection timers for an IPv6 RIP routing process, use the timers basic . Assuming no updates, the route is flushed from the routing table 30 seconds after the end of the hold-down period. CLI Reference Guide 902 - D-Link DGS-6600-48TS | CLI Guide - Page 913
DGS-6604 m Switch > enable Switch # configure terminal Switch (config) # router ipv6 rip Switch (config-router)# timers basic 5 15 30 timers basic CLI Reference Guide 903 - D-Link DGS-6600-48TS | CLI Guide - Page 914
DGS-6604 m timers bgp timers bgp Use this command to adjust BGP network timers. Use the no form of this command to restore the timers to to 50 seconds and the HOLD-TIME timer to 150 seconds: Switch(config)# router bgp 65100 Switch(config-router)# timer bgp 50 150 CLI Reference Guide 904 - D-Link DGS-6600-48TS | CLI Guide - Page 915
DGS-6604 m time-range time-range Use this command to enter the time range configuration mode to define a time range. Use the no form of the Warning! The time-range can not be deleted because it is in use. Verify the settings by entering the show time-range command. CLI Reference Guide 905 - D-Link DGS-6600-48TS | CLI Guide - Page 916
DGS-6604 m traceroute traceroute To display a hop-by-hop path through an IP network from the switch to a specific destination host, use the traceroute TOS is from 0 to 255. IP address in dot notation (a.b.c.d) of the destination host. IPv6 address of the destination host. CLI Reference Guide 906 - D-Link DGS-6600-48TS | CLI Guide - Page 917
DGS-6604 m Default Command Mode Usage Guideline Examples traceroute -w: 5 seconds -i: 1 -m: has reached the destination. Use the TOS option to see if different types of service cause routes to change. Note : The specified OPTIONS can be any combination of each .50.71.123". CLI Reference Guide 907 - D-Link DGS-6600-48TS | CLI Guide - Page 918
DGS-6604 m traceroute Switch# traceroute 172.50.71.123 traceroute to 172.50.71.123 (172.50.71.123), 30 hops max, 40 byte packets 1 172.50.71.123 (172.50.71.123) 0.847 ms 0.344 ms 0.376 ms Switch# CLI Reference Guide 908 - D-Link DGS-6600-48TS | CLI Guide - Page 919
DGS-6604 m Display Field Descriptions traceroute The following table describes the fields in the traceroute command output. Display Field 1 172.50.71.123 (172.50. 1 2001:238:f8a:77:7c10:41c0:6ddd:ecab (2001:238:f8a:77:7c10:41c0:6ddd:ecab) 0.847 ms 0.344 ms 0.376 ms Switch# CLI Reference Guide 909 - D-Link DGS-6600-48TS | CLI Guide - Page 920
DGS-6604 m divided into smaller groups of ports to provide increased security support. The flooding domain for this feature is determined by both is on the top link aggregation module. When any traffic segment member (physical interface) is configured to be a potential aggregated link port, it should - D-Link DGS-6600-48TS | CLI Guide - Page 921
DGS-6604 m Examples traffic-segmentation forward When entering no traffic-segmentation without any keywords, then all ports will become the forward interface eth4.2-4.3 Switch(config-if)# exit Verify the settings by entering the show traffic-segmentation command. CLI Reference Guide 911 - D-Link DGS-6600-48TS | CLI Guide - Page 922
DGS-6604 m trunk allowed-vlan trunk allowed-vlan Use the trunk allowed-VLAN configuration command to set the VLAN characteristic. It sets Switch(config)# interface eth3.1 Switch(config-if)# trunk allowed-vlan 1000 Verify the settings with the show vlan interface command. CLI Reference Guide 912 - D-Link DGS-6600-48TS | CLI Guide - Page 923
DGS-6604 m tunnel destination tunnel destination Use the for a tunnel interface. Tunnel interfaces are valid for this command. Only manually configured tunnels need to set the tunnel destination. This example shows how to settings by entering the show interface command. CLI Reference Guide 913 - D-Link DGS-6600-48TS | CLI Guide - Page 924
DGS-6604 m tunnel mode tunnel mode Use the tunnel mode ipv6ip configuration command to manually specify an IPv6 configured tunnel. The EUI-64 format. This example shows how to specify an IPv6 manually configured tunnel. Switch(config)# interface tunnel 2 Switch(config-if)#tunnel mode ipv6ip - D-Link DGS-6600-48TS | CLI Guide - Page 925
DGS-6604 m tunnel source tunnel source Use the tunnel source configuration command to add the source IPv4 address for the tunnel interface interface tunne 2 Switch(config-if)#no tunnel source Switch(config-if)# Verify the settings by entering the show interface command. CLI Reference Guide 915 - D-Link DGS-6600-48TS | CLI Guide - Page 926
DGS-6604 username username Use the username command to create a user account, and use the no form of the command to delete the user account. text form. If it is in plain-text form, but password encryption is enabled, then the password will be converted to encrypted form. CLI Reference Guide 916 - D-Link DGS-6600-48TS | CLI Guide - Page 927
DGS-6604 Examples username The factory default setting sets the user account to an empty string. When the user account is empty, the a user account with the username admin. Switch(config)# no username admin Verify the settings by entering the show username command. CLI Reference Guide 917 - D-Link DGS-6600-48TS | CLI Guide - Page 928
DGS-6604 m veV rsion version {1 | 2} Use this command to specify the RIP version to send and receive. Syntax Description 1 Only RIP Version 1 -router)#version 2 Switch(config-router)#exit Switch(config)# Verify the settings by entering the show ip protocols rip command. CLI Reference Guide 918 - D-Link DGS-6600-48TS | CLI Guide - Page 929
DGS-6604 m vlan vlan Use the vlan configuration command to add VLANs and to enter the config-vlan mode. Use the no vlan configuration command VLAN id 1000 to 1005. Switch(config)# no vlan 1000-1005 Switch(config)# Verify the settings by entering the show vlan command. CLI Reference Guide 919 - D-Link DGS-6600-48TS | CLI Guide - Page 930
DGS-6604 m vlan encapsulation vlan encapsulation C-VID list). S-VID The VLAN ID specified here refers to the outer-VIDs (i.e. service provider VLAN ID, S-VID). Default Command Mode Usage Guideline Examples No VLAN encapsulation pair is show vlan-tunnel command. CLI Reference Guide 920 - D-Link DGS-6600-48TS | CLI Guide - Page 931
DGS-6604 m vlan name vlan name Use the vlan name VLAN-NAME configuration command to specify the VLAN name. Use the no vlan name command of VLAN 1000. Switch(config)# vlan 1000 Switch(config-vlan)# vlan name admin-vlan Verify the settings by entering the show vlan command. CLI Reference Guide 921 - D-Link DGS-6600-48TS | CLI Guide - Page 932
DGS-6604 m vlan remarking vlan remarking Use VLAN ID, C-VID). S-VID The VLAN ID specified here refers to the outer-VIDs (i.e. service provider VLAN ID, S-VID). Default Command Mode Usage Guideline Example No VLAN remarking pair is -if)#>vlan encapsulation 1001 101-104 CLI Reference Guide 922 - D-Link DGS-6600-48TS | CLI Guide - Page 933
DGS-6604 m vlan remarking 3. Make a VLAN remarking from C-VID 200 to S-VID is 1002. So far the user's COS is trusted. Switch(config VID 101-102. Switch(config-if)#>no cos remarking Switch(config-if)#> 7. Verify the settings by entering show vlan-tunnel interface command. CLI Reference Guide 923 - D-Link DGS-6600-48TS | CLI Guide - Page 934
DGS-6604 m vlan-tunnel vlan-tunnel vlan-tunnel registered VLAN entries will be cleared. Example 4. IIn order to run GVRP on the switch, enable GVRP manually. In VLAN tunnel mode, the SP-VLAN GVRP Address (01-80-C2-00-00-0D) will be by entering show vlan-tunnel command. CLI Reference Guide 924 - D-Link DGS-6600-48TS | CLI Guide - Page 935
DGS-6604 m vlan-tunnel ctag-mapping dynamic vlan-tunnel ctag-mapping dynamic Use this command to enable or disable the dynamic customer )# vlan-tunnel ctag-mapping dynamic ipv4 enable Verify the settings by entering show vlan-tunnel ctag-mapping dynamic state command. CLI Reference Guide 925 - D-Link DGS-6600-48TS | CLI Guide - Page 936
DGS-6604 m vlan-tunnel ctag-mapping static vlan-tunnel ctag-mapping static Use this command to add a static customer VLAN tag mapping entry. Use vlan-tunnel ctag-mapping static 10.90.90.1/24 500 Verify the settings by entering show vlan-tunnel ctag-mapping static command. CLI Reference Guide 926 - D-Link DGS-6600-48TS | CLI Guide - Page 937
DGS-6604 m vlan-tunnel ingress checking vlan- If there is an entry missing, then the packet can optionally be dropped or have a SP VLAN (service provider VLAN) tag added based on the VLAN lookup tables (MAC, Subnet, Protocol, Port VLAN ID entering show vlan-tunnel command. CLI Reference Guide 927 - D-Link DGS-6600-48TS | CLI Guide - Page 938
DGS-6604 m vlan-tunnel interface-type vlan-tunnel interface-type Use this command to configure an interface as NNI (Network-to Network) or (config)#interface eth3.1 Switch(config-if)#vlan-tunnel interface-type nni Verify the settings by entering show vlan-tunnel command. CLI Reference Guide 928 - D-Link DGS-6600-48TS | CLI Guide - Page 939
DGS-6604 m vlan-tunnel remove-inner-tag vlan-tunnel remove-inner-tag Use this command to strip off the packet's inner tag (C-TAG; Switch(config)#interface eth3.1 Switch(config-if)#vlan-tunnel remove-inner-tag Verify the settings by entering show vlan-tunnel command. CLI Reference Guide 929 - D-Link DGS-6600-48TS | CLI Guide - Page 940
DGS-6604 m vlan-tunnel tpid vlan-tunnel tpid Use this command to specify the outer tag TPID at a Network-to-Network Interface (NNI) for Switch(config)#interface eth3.12 Switch(config-if)#vlan-tunnel tpid 0x9100 Verify the settings by entering the show vlan-tunnel command. CLI Reference Guide 930 - D-Link DGS-6600-48TS | CLI Guide - Page 941
DGS-6604 m voice-vlan voice-vlan Use the command to enable the voice VLAN function and to configure a VLAN as a voice VLAN. Use no VLAN. Switch(config)#voice-vlan 1000 Switch(config)#end Switch# You can verify your settings by entering show vlan voice-vlan command. CLI Reference Guide 931 - D-Link DGS-6600-48TS | CLI Guide - Page 942
DGS-6604 m voice-vlan cos voice-vlan cos Use the command to configure the CoS priority for incoming voice VLAN traffic.. voice-vlan cos . Switch(config)#voice-vlan cos 7 Switch(config)#end Switch# You can verify your settings by entering show vlan voice-vlan command. CLI Reference Guide 932 - D-Link DGS-6600-48TS | CLI Guide - Page 943
DGS-6604 m voice-vlan oui voice-vlan oui Use the command to add the user defined OUI of voice device. Use no form of this command are determined as voice packets. The default OUI cannot be deleted. This example shows how to add a user defined OUI of voice device. CLI Reference Guide 933 - D-Link DGS-6600-48TS | CLI Guide - Page 944
DGS-6604 m voice-vlan oui Switch(config)#voice-vlan oui 01-02-03-04-05-06 ff-ff-ff-ff-ff-ff Switch(config)#end Switch# You can verify your settings by show vlan voice-vlan oui command. CLI Reference Guide 934 - D-Link DGS-6600-48TS | CLI Guide - Page 945
DGS-6604 m vrrp critical-ip vrrp critical-ip Use this command to configure the critical IP address. To remove the critical IP address using the no address. Once the ARP cache of critical IP is gone from the ARP table, the master router will give up its master status. CLI Reference Guide 935 - D-Link DGS-6600-48TS | CLI Guide - Page 946
DGS-6604 m Examples vrrp critical-ip The following example shows how to configure the critical-ip address 60.5.1.1 for virtual router 7 with critical-ip address for virtual router 7 on interface vlan1. Switch(config)#interface vlan1 Switch(config-if)#no vrrp 7 critical-ip CLI Reference Guide 936 - D-Link DGS-6600-48TS | CLI Guide - Page 947
DGS-6604 m vrrp ip vrrp ip To enable the Virtual Router Redundancy Protocol (VRRP) on an interface and identify the IP address of the virtual IP address of the virtual router and disable the VRRP on the interface. Switch(config)#interface vlan1 Switch(config-if)#no vrrp 7 CLI Reference Guide 937 - D-Link DGS-6600-48TS | CLI Guide - Page 948
DGS-6604 m vrrp preempt vrrp preempt To configure the router to take over as the master virtual router for a Virtual Router Redundancy Protocol current master router. Switch(config)#interface vlan1 Switch(config-if)#vrrp 7 preempt Switch(config-if)#vrrp 7 priority 200 CLI Reference Guide 938 - D-Link DGS-6600-48TS | CLI Guide - Page 949
DGS-6604 m vrrp preempt The following example shows how to configure the router to disable preempt of a virtual router. Switch(config)#interface vlan1 Switch(config-if)#no vrrp 7 preempt CLI Reference Guide 939 - D-Link DGS-6600-48TS | CLI Guide - Page 950
DGS-6604 m vrrp priority vrrp priority To set the priority of the virtual router, use the vrrp priority command in VRRP interface configuration shows how to configure the router with a priority of 200. Switch(config)#interface vlan1 Switch(config-if)#vrrp 7 priority 200 CLI Reference Guide 940 - D-Link DGS-6600-48TS | CLI Guide - Page 951
DGS-6604 m vrrp priority The following example shows how to restore the default priority of the virtual router. Switch(config)#interface vlan1 Switch(config-if)#no vrrp 7 priority CLI Reference Guide 941 - D-Link DGS-6600-48TS | CLI Guide - Page 952
DGS-6604 m vrrp shutdown vrrp shutdown This command is to disable the VRRP of a VRID on an interface. Use the no form of the command shows how to re-activate VRRP protocol on VRID 7 of interface vlan1. Switch(config)#interface vlan1 Switch(config-if)#no vrrp 7 shutdown CLI Reference Guide 942 - D-Link DGS-6600-48TS | CLI Guide - Page 953
DGS-6604 m vrrp timers advertise vrrp timers advertise This command configures the interval between successive advertisements by the master router. configure the advertisement interval to default. Switch(config)#interface vlan1 Switch(config-if)#no vrrp 7 timers advertise CLI Reference Guide 943 - D-Link DGS-6600-48TS | CLI Guide - Page 954
DGS-6604 m Acronym List ACL ARP BGP BPDU CHAP CIR CIST CLI CLNS CoS CPLD CRC Information Rate Common and Internal Spanning Tree Command-Line Interface Connection-Less Network Service Class of Service Complex Programmable Logic Device Cyclic Redundancy Check Dynamic Host Configuration Protocol Dense - D-Link DGS-6600-48TS | CLI Guide - Page 955
DGS-6604 m dot1q dot1x DRAM DVMRP EAP FAT FIB FTP GARP GBIC GMRP GVRP ICMP IGMP IGMPv2 IGMPv3 IGRP 802.1Q 802. VLAN Registration Protocol Internet Control Message Protocol Internet Group Management Protocol IGMP version 2 IGMP version 3 Interior Gateway Routing Protocol CLI Reference Guide 945 - D-Link DGS-6600-48TS | CLI Guide - Page 956
Protocol data unit Local Area Network Link Access Procedure, Balanced Link Control Protocol Logical Link Control Media Access Control Message Digest 5 Multi-Exit Discriminator Management Information Base multicast route multicast router Multiple Spanning Tree (802.1s) CLI Reference Guide 946 - D-Link DGS-6600-48TS | CLI Guide - Page 957
DGS-6604 m MSTCI MTU NAT NetBIOS NSAP NSF NTP NVRAM OAM OSI OSPF PAE PDU PHY PIM PIM-SM PPP MST configuration identifier Maximum Transmission Unit Network Address Translation Network Basic Input/Output System Network Service Multicast Sparse Mode Point-to-Point Protocol CLI Reference Guide 947 - D-Link DGS-6600-48TS | CLI Guide - Page 958
RADIUS RAM RIB RMON ROM RP RSTP RTP SM Quality of Service Remote Access Dial-In User Service Random-Access Memory Routing Information Base Remote Network Monitor Read-Only Memory Route Processor Rapid Spanning Tree Protocol Real-Time Transport Protocol Sparse Mode (PIM) CLI Reference Guide 948 - D-Link DGS-6600-48TS | CLI Guide - Page 959
default-cost (IPv6) 40 area nssa 41 area range 43 area range (IPv6) 44 area stub 45 area stub (IPv6) 46 area virtual-link 47 area virtual-link (IPv6) 51 arp 53 arp timeout 54 auto-cost reference-bandwidth 55 auto-cost reference-bandwidth (IPv6) 56 banner login 57 based-on client - D-Link DGS-6600-48TS | CLI Guide - Page 960
- clear arp-cache 90 clear counters 91 clear dos prevention counter 92 clear cpu-protect counters 93 clear gvrp statistics interface 94 clear ip bgp 95 clear ip bgp peer-group 97 clear ip dhcp binding 99 clear ip dhcp conflict 101 clear ip dhcp server statistics 103 clear ip ospf 104 clear ipv6 dhcp - D-Link DGS-6600-48TS | CLI Guide - Page 961
- default-metric (IPv6 OSPF) 152 default-metric (RIP) 153 default-metric (RIP IPv6) 154 default-router 155 delete 156 description 157 dir 158 disable 159 distance 160 dns-server 162 domain-name 163 dos_prevention action 164 dos_prevention type 165 dot1v binding protocol-group 167 dot1v protocol- - D-Link DGS-6600-48TS | CLI Guide - Page 962
dhcp relay information trust-all 260 ip dhcp relay information trusted 261 ip dvmrp 262 ip dvmrp metric 263 ip http server 264 ip http service-port 265 ip igmp access-group 266 928 - D-Link DGS-6600-48TS | CLI Guide - Page 963
send version 317 ip rip v2-broadcast 318 ip route 319 ip route multi-path 320 ip ssh 321 ip telnet server 323 ip telnet service-port 324 ip trusted-host 325 ipv6 access-group 327 929 - D-Link DGS-6600-48TS | CLI Guide - Page 964
- ipv6 access-list 329 ipv6 address 330 ipv6 address 331 ipv6 address (management port) 333 ipv6 default-gateway (management port) 334 ipv6 dhcp client information refresh minimum 335 ipv6 dhcp client pd 336 ipv6 dhcp relay destination 338 ipv6 enable 340 ipv6 hop-limit 341 ipv6 nd managed-config- - D-Link DGS-6600-48TS | CLI Guide - Page 965
- lldp tlv-select 396 lldp transmit 398 lldp tx-delay 399 lldp tx-interval 400 logging file 401 logging host 402 logging level 404 logging on 405 login 406 logout 407 loopback-detection (interface) 408 loopback-detection (global) 410 loopback-detection mode 411 loopback-detection interval-time 412 - D-Link DGS-6600-48TS | CLI Guide - Page 966
-list) 473 permit | deny (ipv6 access list) 476 permit | deny (mac access-list) 478 ping 480 poe port priority 482 poe port description 483 poe service-policy 484 poe power-inline 485 police 487 police aggregate 492 police cir 493 policy-map 497 port-channel load-balance 499 power-saving 500 - D-Link DGS-6600-48TS | CLI Guide - Page 967
533 router-id (IPv6) 534 router ipv6 rip 535 router ipv6 ospf 536 router ospf 537 router rip 538 send-lifetime 539 server 541 service dhcp 543 service-policy 544 set 547 set as-path 549 set community 550 set default interface 552 set ip next-hop 553 set ip precedence 555 - D-Link DGS-6600-48TS | CLI Guide - Page 968
ip ospf database summary 671 show ip ospf host-route 673 show ip ospf interface 674 show ip ospf neighbor 676 show ip ospf virtual-links 677 show ip pim 679 show ip pim bsr 680 show ip pim interface 681 show ip pim mroute 683 show ip pim neighbor 685 - D-Link DGS-6600-48TS | CLI Guide - Page 969
711 show ipv6 ospf database 712 show ipv6 ospf interface 713 show ipv6 ospf neighbor 714 show ipv6 ospf route 715 show ipv6 ospf virtual-links 716 show ipv6 protocols 717 show ipv6 rip database 719 show ipv6 rip interface 720 show ipv6 route 721 show ipv6 route summary 723 show - D-Link DGS-6600-48TS | CLI Guide - Page 970
- show ssh 762 show startup-config 763 show storm-control 764 show system 766 show time-range 770 show traffic-segmentation 771 show unit 772 show username 773 show user-session 774 show version 775 show vlan 776 show vlan-tunnel 781 show vlan-tunnel ctag-mapping 784 show vrrp 785 show vrrp brief - D-Link DGS-6600-48TS | CLI Guide - Page 971
(Interface configuration) 860 spanning-tree (timers) 861 spanning-tree cost 862 spanning-tree fast-forwarding 863 spanning-tree guard root 864 spanning-tree link-type 865 spanning-tree mode 866 spanning-tree mst (cost | port-priority) 867 spanning-tree mst (forward | max-age | max-hops) 868 spanning - D-Link DGS-6600-48TS | CLI Guide - Page 972
- vlan-tunnel ctag-mapping static 926 vlan-tunnel ingress checking 927 vlan-tunnel interface-type 928 vlan-tunnel remove-inner-tag 929 vlan-tunnel tpid 930 voice-vlan 931 voice-vlan cos 932 voice-vlan oui 933 vrrp critical-ip 935 vrrp ip 937 vrrp preempt 938 vrrp priority 940 vrrp shutdown 942 vrrp
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316
-
317
-
318
-
319
-
320
-
321
-
322
-
323
-
324
-
325
-
326
-
327
-
328
-
329
-
330
-
331
-
332
-
333
-
334
-
335
-
336
-
337
-
338
-
339
-
340
-
341
-
342
-
343
-
344
-
345
-
346
-
347
-
348
-
349
-
350
-
351
-
352
-
353
-
354
-
355
-
356
-
357
-
358
-
359
-
360
-
361
-
362
-
363
-
364
-
365
-
366
-
367
-
368
-
369
-
370
-
371
-
372
-
373
-
374
-
375
-
376
-
377
-
378
-
379
-
380
-
381
-
382
-
383
-
384
-
385
-
386
-
387
-
388
-
389
-
390
-
391
-
392
-
393
-
394
-
395
-
396
-
397
-
398
-
399
-
400
-
401
-
402
-
403
-
404
-
405
-
406
-
407
-
408
-
409
-
410
-
411
-
412
-
413
-
414
-
415
-
416
-
417
-
418
-
419
-
420
-
421
-
422
-
423
-
424
-
425
-
426
-
427
-
428
-
429
-
430
-
431
-
432
-
433
-
434
-
435
-
436
-
437
-
438
-
439
-
440
-
441
-
442
-
443
-
444
-
445
-
446
-
447
-
448
-
449
-
450
-
451
-
452
-
453
-
454
-
455
-
456
-
457
-
458
-
459
-
460
-
461
-
462
-
463
-
464
-
465
-
466
-
467
-
468
-
469
-
470
-
471
-
472
-
473
-
474
-
475
-
476
-
477
-
478
-
479
-
480
-
481
-
482
-
483
-
484
-
485
-
486
-
487
-
488
-
489
-
490
-
491
-
492
-
493
-
494
-
495
-
496
-
497
-
498
-
499
-
500
-
501
-
502
-
503
-
504
-
505
-
506
-
507
-
508
-
509
-
510
-
511
-
512
-
513
-
514
-
515
-
516
-
517
-
518
-
519
-
520
-
521
-
522
-
523
-
524
-
525
-
526
-
527
-
528
-
529
-
530
-
531
-
532
-
533
-
534
-
535
-
536
-
537
-
538
-
539
-
540
-
541
-
542
-
543
-
544
-
545
-
546
-
547
-
548
-
549
-
550
-
551
-
552
-
553
-
554
-
555
-
556
-
557
-
558
-
559
-
560
-
561
-
562
-
563
-
564
-
565
-
566
-
567
-
568
-
569
-
570
-
571
-
572
-
573
-
574
-
575
-
576
-
577
-
578
-
579
-
580
-
581
-
582
-
583
-
584
-
585
-
586
-
587
-
588
-
589
-
590
-
591
-
592
-
593
-
594
-
595
-
596
-
597
-
598
-
599
-
600
-
601
-
602
-
603
-
604
-
605
-
606
-
607
-
608
-
609
-
610
-
611
-
612
-
613
-
614
-
615
-
616
-
617
-
618
-
619
-
620
-
621
-
622
-
623
-
624
-
625
-
626
-
627
-
628
-
629
-
630
-
631
-
632
-
633
-
634
-
635
-
636
-
637
-
638
-
639
-
640
-
641
-
642
-
643
-
644
-
645
-
646
-
647
-
648
-
649
-
650
-
651
-
652
-
653
-
654
-
655
-
656
-
657
-
658
-
659
-
660
-
661
-
662
-
663
-
664
-
665
-
666
-
667
-
668
-
669
-
670
-
671
-
672
-
673
-
674
-
675
-
676
-
677
-
678
-
679
-
680
-
681
-
682
-
683
-
684
-
685
-
686
-
687
-
688
-
689
-
690
-
691
-
692
-
693
-
694
-
695
-
696
-
697
-
698
-
699
-
700
-
701
-
702
-
703
-
704
-
705
-
706
-
707
-
708
-
709
-
710
-
711
-
712
-
713
-
714
-
715
-
716
-
717
-
718
-
719
-
720
-
721
-
722
-
723
-
724
-
725
-
726
-
727
-
728
-
729
-
730
-
731
-
732
-
733
-
734
-
735
-
736
-
737
-
738
-
739
-
740
-
741
-
742
-
743
-
744
-
745
-
746
-
747
-
748
-
749
-
750
-
751
-
752
-
753
-
754
-
755
-
756
-
757
-
758
-
759
-
760
-
761
-
762
-
763
-
764
-
765
-
766
-
767
-
768
-
769
-
770
-
771
-
772
-
773
-
774
-
775
-
776
-
777
-
778
-
779
-
780
-
781
-
782
-
783
-
784
-
785
-
786
-
787
-
788
-
789
-
790
-
791
-
792
-
793
-
794
-
795
-
796
-
797
-
798
-
799
-
800
-
801
-
802
-
803
-
804
-
805
-
806
-
807
-
808
-
809
-
810
-
811
-
812
-
813
-
814
-
815
-
816
-
817
-
818
-
819
-
820
-
821
-
822
-
823
-
824
-
825
-
826
-
827
-
828
-
829
-
830
-
831
-
832
-
833
-
834
-
835
-
836
-
837
-
838
-
839
-
840
-
841
-
842
-
843
-
844
-
845
-
846
-
847
-
848
-
849
-
850
-
851
-
852
-
853
-
854
-
855
-
856
-
857
-
858
-
859
-
860
-
861
-
862
-
863
-
864
-
865
-
866
-
867
-
868
-
869
-
870
-
871
-
872
-
873
-
874
-
875
-
876
-
877
-
878
-
879
-
880
-
881
-
882
-
883
-
884
-
885
-
886
-
887
-
888
-
889
-
890
-
891
-
892
-
893
-
894
-
895
-
896
-
897
-
898
-
899
-
900
-
901
-
902
-
903
-
904
-
905
-
906
-
907
-
908
-
909
-
910
-
911
-
912
-
913
-
914
-
915
-
916
-
917
-
918
-
919
-
920
-
921
-
922
-
923
-
924
-
925
-
926
-
927
-
928
-
929
-
930
-
931
-
932
-
933
-
934
-
935
-
936
-
937
-
938
-
939
-
940
-
941
-
942
-
943
-
944
-
945
-
946
-
947
-
948
-
949
-
950
-
951
-
952
-
953
-
954
-
955
-
956
-
957
-
958
-
959
-
960
-
961
-
962
-
963
-
964
-
965
-
966
-
967
-
968
-
969
-
970
-
971
-
972
 |
 |
0.9.3