D-Link DSL-300T User Manual - Page 30

Username, Password, Encapsulation, Apply, Save All, System, Commands, Tools

Get D-Link DSL-300T PDF manuals and user guides View all D-Link DSL-300T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

DSL-300T ADSL Modem User's Guide To setup a PPPoA connection for the first time: 1. Type in a Name in the space provided if you wish or leave the default name. 2. Make sure PPPoA appears listed as the Type: of connection protocol used. 3. Do not change the VPI or VCI values unless you are required to do so. If these settings are incorrect, the ADSL connection will not function. Many users will be able to use the default settings. If you are told to change these, type in the values given to you by your service provider. 4. Leave the default QoS values if you are unsure or the ISP did not provide this information. 5. Do not change the PCR or SCR values unless you are required to do so. If you are told to change these, type in the values given to you by your service provider. 6. Supply a Username and Password used to verify the identity of your account. These are usually provided by your ISP. 7. The Encapsulation values LLC (SNAP) and VC (MUX) are two different methods of encapsulating the PPP packet. Contact your ISP to make sure which encapsulation is being supported. 8. For most users, the remaining settings will not need to be changed. See your ISP for further information. 9. Click the Apply button when you have entered all the information. The browser window may briefly go blank. After a few seconds the new connection you just configured will become the active connection for the Modem. 10. To make your temporarily saved connection permanent, click the Save All button in the System Commands window on the Tools tab. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
DSL-300T ADSL Modem User’s Guide
To setup a PPPoA connection for the first time:
1.
Type in a
Name
in the space provided if you wish or leave the default name.
2.
Make sure
PPPoA
appears listed as the
Type:
of connection protocol used.
3.
Do not change the
VPI
or
VCI
values unless you are required to do so. If these settings are incorrect, the
ADSL connection will not function. Many users will be able to use the default settings. If you are told to
change these, type in the values given to you by your service provider.
4.
Leave the default
QoS
values if you are unsure or the ISP did not provide this information.
5.
Do not change the
PCR
or
SCR
values unless you are required to do so. If you are told to change these, type
in the values given to you by your service provider.
6.
Supply a
Username
and
Password
used to verify the identity of your account. These are usually provided
by your ISP.
7.
The
Encapsulation
values LLC (SNAP) and VC (MUX) are two different methods of encapsulating the
PPP packet. Contact your ISP to make sure which encapsulation is being supported.
8.
For most users, the remaining settings will not need to be changed. See your ISP for further information.
9.
Click the
Apply
button when you have entered all the information. The browser window may briefly go
blank. After a few seconds the new connection you just configured will become the active connection for the
Modem.
10. To make your temporarily saved connection permanent, click the
Save All
button in the
System
Commands
window on the
Tools
tab.
20