D-Link DSL-300T User Manual - Page 32

Bridge, Setup - New Connection Bridge window

Get D-Link DSL-300T PDF manuals and user guides View all D-Link DSL-300T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

DSL-300T ADSL Modem User's Guide 7. The Encapsulation values LLC (SNAP) and VC (MUX) are two different methods of encapsulating the PPP packet. Contact your ISP to make sure which encapsulation is being supported. 8. For most users, the remaining settings will not need to be changed. See your ISP for further information. 9. Click the Apply button when you have entered all the information. The browser window may briefly go blank. After a few seconds the new connection you just configured will become the active connection for the Modem. 10. To make your temporarily saved connection permanent, click the Save All button in the System Commands window on the Tools tab. Bridge Make sure you have selected Bridge from the Type: pull-down menu so that you are now configuring setting in the menu titled "Bridged Connection Setup". Follow the instructions below to set up the connection. Figure 3-6. Setup - New Connection (Bridge) window To configure the WAN connection for Bridge, perform the steps listed below. Some of the settings do not need to be changed when you first set up the device but can be changed later if you choose. "Bridge" means a pure bridged connection with no IP address assigned to the Modem. This connection method makes the Modem act as a bridge, and just passes packets across the DSL port. 1. Type in a Name in the space provided if you wish or leave the default name. 2. Make sure Bridge appears listed as the Type: of connection protocol used. 3. Do not change the VPI or VCI values unless you are required to do so. If these settings are incorrect, the ADSL connection will not function. Many users will be able to use the default settings. If you are told to change these, type in the values given to you by your service provider. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
DSL-300T ADSL Modem User’s Guide
7.
The
Encapsulation
values LLC (SNAP) and VC (MUX) are two different methods of encapsulating the
PPP packet. Contact your ISP to make sure which encapsulation is being supported.
8.
For most users, the remaining settings will not need to be changed. See your ISP for further information.
9.
Click the
Apply
button when you have entered all the information. The browser window may briefly go
blank. After a few seconds the new connection you just configured will become the active connection for the
Modem.
10. To make your temporarily saved connection permanent, click the
Save All
button in the
System
Commands
window on the
Tools
tab.
Bridge
Make sure you have selected Bridge from the
Type:
pull-down menu so that you are now configuring setting in
the menu titled “Bridged Connection Setup”. Follow the instructions below to set up the connection.
Figure 3-6. Setup – New Connection (Bridge) window
To configure the WAN connection for Bridge, perform the steps listed below. Some of the settings do not need
to be changed when you first set up the device but can be changed later if you choose.
“Bridge” means a pure bridged connection with no IP address assigned to the Modem. This connection method
makes the Modem act as a bridge, and just passes packets across the DSL port.
1.
Type in a
Name
in the space provided if you wish or leave the default name.
2.
Make sure
Bridge
appears listed as the
Type:
of connection protocol used.
3.
Do not change the
VPI
or
VCI
values unless you are required to do so. If these settings are incorrect, the
ADSL connection will not function. Many users will be able to use the default settings. If you are told to
change these, type in the values given to you by your service provider.
22