D-Link DSL-300T User Manual - Page 33

Static IP, Encapsulation, Apply, Save All, System, Commands, Tools, Connection 1, WAN Setup

Get D-Link DSL-300T PDF manuals and user guides View all D-Link DSL-300T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

DSL-300T ADSL Modem User's Guide 4. Leave the default QoS values if you are unsure or the ISP did not provide this information. 5. Do not change the PCR or SCR values unless you are required to do so. If you are told to change these, type in the values given to you by your service provider. 6. The Encapsulation values LLC (SNAP) and VC (MUX) are two different methods of encapsulating the PPP packet. Contact your ISP to make sure which encapsulation is being supported. 7. Click the Apply button when you have entered all the information. The browser window may briefly go blank. After a few seconds the new connection you just configured will become the active connection for the Modem. 8. To make your temporarily saved connection permanent, click the Save All button in the System Commands window on the Tools tab. Static IP Static is used whenever a known static IP is assigned. The accompanying information such as the Subnet mask and the gateway should also be specified in order to be able to connect. Up to three Domain Name Server (DNS) addresses can also be specified. These are the servers would enable you to have access to other web servers. Valid IP addresses range from 0.0.0.0 to 255.255.255.255. Figure 3- 7. Setup Static IP To configure the WAN connection for Static, perform the steps listed below. Some of the settings do not need to be changed the first time the device is set up, but can be changed later if you choose. 1. Click the Connection 1 button under WAN Setup to view the default PPPoA Connection Setup configuration menu. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
DSL-300T ADSL Modem User’s Guide
4.
Leave the default
QoS
values if you are unsure or the ISP did not provide this information.
5.
Do not change the
PCR
or
SCR
values unless you are required to do so. If you are told to change these, type
in the values given to you by your service provider.
6.
The
Encapsulation
values LLC (SNAP) and VC (MUX) are two different methods of encapsulating the
PPP packet. Contact your ISP to make sure which encapsulation is being supported.
7.
Click the
Apply
button when you have entered all the information. The browser window may briefly go
blank. After a few seconds the new connection you just configured will become the active connection for the
Modem.
8.
To make your temporarily saved connection permanent, click the
Save All
button in the
System
Commands
window on the
Tools
tab.
Static IP
Static is used whenever a known static IP is assigned. The accompanying information such as the Subnet mask
and the gateway should also be specified in order to be able to connect. Up to three Domain Name Server (DNS)
addresses can also be specified. These are the servers would enable you to have access to other web servers.
Valid IP addresses range from 0.0.0.0 to 255.255.255.255.
Figure 3- 7. Setup Static IP
To configure the WAN connection for Static, perform the steps listed below. Some of the settings do not need to
be changed the first time the device is set up, but can be changed later if you choose.
1.
Click the
Connection 1
button under
WAN Setup
to view the default
PPPoA Connection Setup
configuration menu.
23