Dell C1048P Port Extender Networking C1048P Getting Started Guide - Page 5

C1048P Front Panel, rate, 8 data bits, No Parity, 1 Stop Bit, and No Flow Control.

Get Dell C1048P Port Extender PDF manuals and user guides View all Dell C1048P Port Extender manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

• Warranty and Support Information • Software License Agreement You can order additional items, such as optics, cables, and external power supplies. C1048P Front Panel The ports on the front panel of the C1048P PE are shown in the following illustration and described below. Figure 1. C1048P Front Panel: Ports and Reset Button 1. Console port The console port provides serial communication using the RS-232 protocol to connect a console terminal and access the C1048P command-line interface (CLI). To set up a console connection, use the serial cable (RJ-45 to DB-9 female connectors) shipped with the C9010. The console port operates as an asynchronous link from 1200 to 115,200 baud. The default settings are 9600 baud rate, 8 data bits, No Parity, 1 Stop Bit, and No Flow Control. 2. USB port The Type-A, female USB port supports a USB 2.0-compliant flash memory drive. The C1048P can read or write to a flash drive formatted as FAT-32. Use a USB flash drive to copy files and images to the C1048P. 3. Reset button Access the reset button through a pinhole. To perform a hard reset of the C1048P, insert the tip of a paper clip or similar tool into the pinhole. When the PE reboots, it re-establishes communication with an attached C9010, which downloads the latest SW configuration settings. 4. Two 10GbE SFP+ ports Two SFP+ ports provide 10GbE uplinks to communicate with a C9010. To connect to a C9010 switch, at least one C1048P 10GbE SFP+ port is required. On the C1048P, 10GbE SFP+ ports are numbered 1 and 2, and only support uplinks to a parent C9010; they cannot be used as data ports. 5. Forty-eight Gigabit Ethernet ports C1048P Hardware Description 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
•
Warranty and Support Information
•
Software License Agreement
You can order additional items, such as optics, cables, and external power supplies.
C1048P Front Panel
The ports on the front panel of the C1048P PE are shown in the following illustration and described
below.
Figure 1. C1048P Front Panel: Ports and Reset Button
1.
Console port
The console port provides serial communication using the RS-232 protocol to connect a console
terminal and access the C1048P command-line interface (CLI). To set up a console connection, use
the serial cable (RJ-45 to DB-9 female connectors) shipped with the C9010. The console port
operates as an asynchronous link from 1200 to 115,200 baud. The default settings are 9600 baud
rate, 8 data bits, No Parity, 1 Stop Bit, and No Flow Control.
2.
USB port
The Type-A, female USB port supports a USB 2.0-compliant flash memory drive. The C1048P can
read or write to a flash drive formatted as FAT-32. Use a USB flash drive to copy files and images to
the C1048P.
3.
Reset button
Access the reset button through a pinhole. To perform a hard reset of the C1048P, insert the tip of a
paper clip or similar tool into the pinhole. When the PE reboots, it re-establishes communication
with an attached C9010, which downloads the latest SW configuration settings.
4.
Two 10GbE SFP+ ports
Two SFP+ ports provide 10GbE uplinks to communicate with a C9010. To connect to a C9010
switch, at least one C1048P 10GbE SFP+ port is required. On the C1048P, 10GbE SFP+ ports are
numbered 1 and 2, and only support uplinks to a parent C9010; they cannot be used as data ports.
5.
Forty-eight Gigabit Ethernet ports
C1048P Hardware Description
5