Dell Dimension 4700 Owner's Manual - Page 67

If you replaced a card that was already installed in the computer and you removed the top

Get Dell Dimension 4700 PDF manuals and user guides View all Dell Dimension 4700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

5 If you are installing the card into the x16 card connector, position the card so the securing slot is aligned with the securing tab, and gently pull the securing tab. 6 Place the card in the connector and press down firmly. Ensure that the card is fully seated and that the bracket is within the card slot. not fully seated card fully seated card bracket within slot bracket caught outside of slot 7 If you replaced a card that was already installed in the computer and you removed the top of the retention mechanism, you may reinstall the top. 8 Secure the card bracket with the screw you removed in step 2. NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment. 9 Connect any cables that should be attached to the card. See the documentation for the card for information about the card's cable connections. NOTICE: To connect a network cable, first plug the cable into the network device and then plug it into the computer. 10 Close the computer cover, reconnect the computer and devices to electrical outlets, and then turn them on. Removing and Installing Parts 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Removing and Installing Parts
67
5
If you are installing the card into the x16 card connector, position the card so the securing slot
is aligned with the securing tab, and gently pull the securing tab.
6
Place the card in the connector and press down firmly. Ensure that the card is fully seated and
that the bracket is within the card slot.
7
If you replaced a card that was already installed in the computer and you removed the top of
the retention mechanism, you may reinstall the top.
8
Secure the card bracket with the screw you removed in step 2.
NOTICE:
Do not route card cables over or behind the cards. Cables routed over the cards can prevent
the computer cover from closing properly or cause damage to the equipment.
9
Connect any cables that should be attached to the card.
See the documentation for the card for information about the card’s cable connections.
NOTICE:
To connect a network cable, first plug the cable into the network device and then plug it into
the computer.
10
Close the computer cover, reconnect the computer and devices to electrical outlets, and then
turn them on.
fully seated card
not fully seated card
bracket caught
outside of slot
bracket
within slot