Dell Inspiron 24 5415 All-in-One Service Manual - Page 52

Installing the system board

Get Dell Inspiron 24 5415 All-in-One PDF manuals and user guides View all Dell Inspiron 24 5415 All-in-One manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Steps 1. Disconnect the touchscreen cable from the system board. NOTE: This cable is only available on computers that support touch option. 2. Disconnect the camera cable from the system board. 3. Disconnect the backlight cable from the system board. 4. Disconnect the fan cable from the system board. 5. Disconnect the speaker cable from the system board. 6. Disconnect the microphone-module cable from the system board. 7. Open the latch and disconnect the media-card reader cable from the system board. 8. Open the latch and disconnect the power-button board cable from the system board. 9. Open the latch and disconnect the display cable from the system board. 10. Remove the six screws (M3x5) that secure the system board to the display-assembly base. 11. Remove the solid-state drive screw mount (M3x4) that secures the system board to the display-assembly base. 12. Lift the system board off the display-assembly base. Installing the system board Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the connectors on your system board. 52 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Steps
1.
Disconnect the touchscreen cable from the system board.
NOTE:
This cable is only available on computers that support touch option.
2.
Disconnect the camera cable from the system board.
3.
Disconnect the backlight cable from the system board.
4.
Disconnect the fan cable from the system board.
5.
Disconnect the speaker cable from the system board.
6.
Disconnect the microphone-module cable from the system board.
7.
Open the latch and disconnect the media-card reader cable from the system board.
8.
Open the latch and disconnect the power-button board cable from the system board.
9.
Open the latch and disconnect the display cable from the system board.
10.
Remove the six screws (M3x5) that secure the system board to the display-assembly base.
11.
Remove the solid-state drive screw mount (M3x4) that secures the system board to the display-assembly base.
12.
Lift the system board off the display-assembly base.
Installing the system board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the connectors on your system board.
52
Removing and installing components