Dell Inspiron 27 7720 All-in-One Owners Manual - Page 45

Installing the stand, Steps, Prerequisites, About this task

Get Dell Inspiron 27 7720 All-in-One PDF manuals and user guides View all Dell Inspiron 27 7720 All-in-One manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Steps 1. Locate the tab on the stand, and push a scribe into the tab to release the stand from the display-assembly base. 2. Lift the stand off the display-assembly base. Installing the stand Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. NOTE: The following procedure is applicable for both Y stand and Isosceles stand. NOTE: For replacement of stand or display hinges, the replacement kit is shipped with both stand and display hinges, and you must replace both of these components together. Refer to the procedure for removing the stand hinges and installing the stand hinges. About this task The following image indicates the location of the stand and provides a visual representation of the installation procedure. Removing and installing Customer Replaceable Units (CRUs) 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Steps
1.
Locate the tab on the stand, and push a scribe into the tab to release the stand from the display-assembly base.
2.
Lift the stand off the display-assembly base.
Installing the stand
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
NOTE:
The following procedure is applicable for both Y stand and Isosceles stand.
NOTE:
For replacement of stand or display hinges, the replacement kit is shipped with both stand and display hinges, and
you must replace both of these components together. Refer to the procedure for
removing the stand hinges
and
installing
the stand hinges
.
About this task
The following image indicates the location of the stand and provides a visual representation of the installation procedure.
Removing and installing Customer Replaceable Units (CRUs)
45