Dell OptiPlex 380 Service Manual - Page 5

Enable with Boot NIC - recovery

Get Dell OptiPlex 380 PDF manuals and user guides View all Dell OptiPlex 380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

CPU XD Support Computrace(R) NOTE: When TPM Security is set to Clear the system setup program clears the user information stored in the TPM. Enables or disables the execute disable mode of the processor. This option is enabled by default. Enables or disables the optional Computrace® service designed for asset management. You can set this option to: l Deactivate (default) l Disable l Activate SATA-0 Password Displays the current status of the password set for the hard drive connected to the SATA-0 connector on the system board. You can also set a new password. This option is not set by default. NOTE: The system setup program displays a password for each of the hard drives connected to your system board. Power Management AC Recovery Determines how the computer responds when AC power is re-applied after a power loss. You can set the AC Recovery to: l Power Off (default) l Power On l Last State Auto On Time Sets time to automatically turn on the computer. Time is kept in the standard 12-hour format (hours:minutes:seconds). Change the startup time by typing the values in the time and AM/PM fields. NOTE: This feature does not work if you turn off your computer using the switch on a power strip or surge protector or if Auto Power On is set to disabled. Low Power Mode Enables or disables low power mode. This option is disabled by default. When low power mode is enabled, the integrated network card is disabled when the computer shutsdown or hibernates. Only add-in network cards will be able to remotely wake the computer. Remote Wakeup Allows the computer to power up when a network interface controller receives a wake up signal. You can set Remote Wakeup to: l Disable (default) l Enable l Enable with Boot NIC Suspend Mode Sets the power management suspend mode to: l S1 l S3 (default) Fan Control Override Controls the speed of the system fan. NOTE: When enabled, the fan runs at full speed. Maintenance Service Tag Asset Tag SERR Messages Displays the Service Tag of your computer. Allows you to create a system asset tag if an asset tag is not already set. This option is not set by default. Controls the SERR Message mechanism. This option is enabled by default. Some graphics cards require the SERR Message mechanism be disabled. Image Server Lookup Method ImageServer IP Specifies how the ImageServer looks up the server address. l Static IP l DNS NOTE: You must set the Integrated NIC to Enable with ImageServer to set the Lookup Method. Specifies the primary static IP address of the ImageServer with which the client software communicates. The default IP address is 255.255.255.255 NOTE: You must set the Integrated NIC to Enable with ImageServer to set the ImageServer IP.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
NOTE: When TPM Security is set to
Clear the system setup program clears the user information stored in the TPM.
CPU XD Support
Enables or disables the execute disable mode of the processor.
This option is enabled by default.
Computrace(R)
Enables or disables the optional Computrace
®
service designed for asset management.
You can set this option to:
l
Deactivate
(default)
l
Disable
l
Activate
SATA-0 Password
Displays the current status of the password set for the hard drive connected to the SATA-0 connector on the system board.
You can also set a new password. This option is not set by default.
NOTE: The system setup program displays a password for each of the hard drives connected to your system board.
Power Management
AC Recovery
Determines how the computer responds when AC power is re-applied after a power loss. You can set the AC Recovery to:
l
Power Off
(default)
l
Power On
l
Last State
Auto On Time
Sets time to automatically turn on the computer.
Time is kept in the standard 12-hour format (hours:minutes:seconds).
Change the startup time by typing the values in the time and AM/PM fields.
NOTE: This feature does not work if you turn off your computer using the switch on a power strip or surge protector or if
Auto Power On is
set to disabled.
Low Power Mode
Enables or disables low power mode.
This option is disabled by default.
When low power mode is enabled, the integrated network card is disabled when the computer shutsdown or hibernates. Only add-in
network cards will be able to remotely wake the computer.
Remote Wakeup
Allows the computer to power up when a network interface controller receives a wake up signal
.
You can set Remote Wakeup to:
l
Disable
(default)
l
Enable
l
Enable with Boot NIC
Suspend Mode
Sets the power management suspend mode to:
l
S1
l
S3
(default)
Fan Control
Override
Controls the speed of the system fan.
NOTE: When enabled, the fan runs at full speed.
Maintenance
Service Tag
Displays the Service Tag of your computer.
Asset Tag
Allows you to create a system asset tag if an asset tag is not already set.
This option is not set by default.
SERR Messages
Controls the SERR Message mechanism.
This option is enabled by default.
Some graphics cards require the SERR Message mechanism be disabled.
Image Server
Lookup Method
Specifies how the ImageServer looks up the server address.
l
Static IP
l
DNS
NOTE: You must set the
Integrated NIC
to
Enable
with
ImageServer
to set the
Lookup Method.
ImageServer IP
Specifies the primary static IP address of the ImageServer with which the client software communicates.
The default IP address is
255.255.255.255
NOTE:
You must set the
Integrated NIC
to
Enable
with
ImageServer
to set the
ImageServer IP.