Dell PowerVault 210S Dell PowerVault 200S and 210S Storage Systems Rack I - Page 20
Dell PowerVault 200S and 210S Storage Systems Rack Installation Guide, hinge, release, lever
 |
View all Dell PowerVault 210S manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 20 highlights
hinge release lever Repeat steps 1 and 2 to remove the back door from the rack. Store the doors in an area where they will not fall over while you install the kit. To install the rail assemblies in the rack, perform the following steps: 1. Ensure that there is enough room in the rack to install the storage system. The storage system takes 5.25 inches (3Us) of vertical space. 2. If the two adjustable rail-mounting flanges are not already attached to the support rails, attach one flange to each of the support rails using two 10-32 x 1/2-inch pan-head screws, as shown in Figure 1-6. Do not tighten the screws at this time. 1-6 Dell PowerVault 200S and 210S Storage Systems Rack Installation Guide
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15 -
16 -
17 -
18 -
19 -
20 -
21 -
22 -
23 -
24 -
25 -
26
 |
 |
1-6
Dell PowerVault 200S and 210S Storage Systems Rack Installation Guide
±²³´µ¶·¸¹!º··»¶Ï°²Ã³·Àȶ·ÉŹʷ»¼½¾·Á¼Ë²Ã¶À·ÌµÄ
Repeat steps 1 and 2 to remove the back door from the rack.
Store the doors in an area where they will not fall over while you install the kit.
+³¾»µ¶¶¼³Ä·»Í²·Çµ¼¶·!¾¾²Æ˶¼²¾·¼³·»Í²·Çµ¹È
$¹%±´±&·¸´Ê¸ËÅ̸¾ÃÀ¸º»Á¿¾Æƺ»È¸ÇÅÃÀ¸¿Â¾»¸Å»À¸Á¿ÅþÈÀ¸ÁËÁ¿ÀÇ"¸º»Á¿¾ÆƸ¿ÂÀ¸
ʺÃÁ¿¸Á¿ÅþÈÀ¸ÁËÁ¿ÀǸº»¸¿ÂÀ¸ÆÅÉÀÁ¿¸ÄÅÁº¿ºÅ»¸¿Å¸ÂÀÆĸÄÃÀÍÀ»¿¸¿ÂÀ¸Ã¾½1¸ÊÃÅǸ¿ºÄ)
ĺ»È¸¾»¼¸º»#Ìú»È¸ÁÅÇÀÅ»À¸ÉÂÀ»¸¿ÂÀ¸Á¿ÅþÈÀ¸ÁËÁ¿ÀǸºÁ¸ÄÌÆÆÀ¼¸ÅÌ¿¸Åʸ¿ÂÀ¸
þ½1¸Å»¸¿ÂÀ¸Ã¾ºÆ¸¾ÁÁÀÇÎƺÀÁÏ
To install the rail assemblies in the rack, perform the following steps:
1.
Ensure that there is enough room in the rack to install the storage system.
The storage system takes 5.25 inches (3Us) of vertical space.
2.
If the two adjustable rail-mounting flanges are not already attached to the support
rails, attach one flange to each of the support rails using two 10-32 x 1/2-inch
pan-head screws, as shown in Figure 1-6. Do not tighten the screws at this time.
hinge
release
lever