Home » Dewalt Manuals » Tools » Dewalt DXCM201 » Manual Viewer

Dewalt DXCM201 Instruction Manual

Dewalt DXCM201 Manual

View all Dewalt DXCM201 manuals

Add to My Manuals
Save this manual to your list of manuals

Dewalt DXCM201 manual content summary:

Dewalt DXCM201 | Instruction Manual - Page 1
19) Part No. E112138 DXCM201 Copyright © 2019 DEWALT If you have questions or comments, contact us. Pour toute question ou tout commentaire, nous contacter. Si tiene dudas o comentarios, contáctenos. 1-888-895-4549 • www.DEWALT.com INSTRUCTION MANUAL GUIDE D'UTILISATION MANUAL DE INSTRUCCIONES
Dewalt DXCM201 | Instruction Manual - Page 2
head Weight: 27.0 lbs (12.2 kg.) Oil Capacity: 16 fl. oz. (473 mL) Specifications A I K J C B D F/L E G H MODEL WEIGHT HEIGHT WIDTH LENGTH AIR TANK CAPACITY DXCM201 137 lbs. (62.1 kg) 32" 22" 33" WITHOUT FRONT HANDLE 20 GALLONS (75.7 L) APPROX. CUT OUT PRESSURE AIR DELIVERY TANK FILL TIME INPUT
Dewalt DXCM201 | Instruction Manual - Page 3
Fig. 1 Hot Surfaces Fig. 2 OFF AUTO English COMPRESSOR CYLINDER & HEAD PUMP CRANKCASE OUTLET TUBE Fig. 3 CLOSE OPEN J = Oil drain plug K = Oil level sight glass I = Oil fill plug I FULL ADD K J 3
Dewalt DXCM201 | Instruction Manual - Page 4
ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DeWALT TOOL, CALL US TOLL FREE AT: 1-888-895-4549 Important Safety Instructions WARNING: Do not operate this unit until you read this instruction manual for safety, operation and maintenance instructions. WARNING: CONTAINS LEAD. May be harmful if eaten
Dewalt DXCM201 | Instruction Manual - Page 5
filters and in-line safety equipment for human consumption. • Work in an area with good cross ventilation. Read and follow the safety instructions provided on the label or safety data sheets for the materials you are spraying. Always use certified safety equipment: NIOSH/OSHA respiratory protection
Dewalt DXCM201 | Instruction Manual - Page 6
posing risk of injury to consumers. Your compressor air tank must be removed from service by the end of the year shown on your tank warning label. The following to withstand specific operating pressures. Never make adjustments or part substitutions to alter the factory set operating pressures. •
Dewalt DXCM201 | Instruction Manual - Page 7
certified safety equipment: ANSI Z87.1 eye protection (CAN/CSA Z94.3) with side shields when using the compressor. • Never point any nozzle or sprayer toward any part of the body or at other people or animals. • Always turn the compressor off and bleed pressure from the air hose and air tank before
Dewalt DXCM201 | Instruction Manual - Page 8
burns. • Never touch any exposed metal parts on compressor during or immediately after operation. Compressor from electrocution. Refer to Grounding Instructions paragraph in the Installation section. product should be performed by authorized service center personnel in accordance with national
Dewalt DXCM201 | Instruction Manual - Page 9
with damaged or missing parts or attempting to repair compressor with protective shrouds removed can expose you to moving parts and can result in serious injury. • Any repairs required on this product should be performed by a DeWALT factory service center or a DeWALT authorized service center. 9
Dewalt DXCM201 | Instruction Manual - Page 10
to hearing loss. • Always wear certified safety equipment: ANSI S12.6 (S3.19) hearing protection. SAVE THESE INSTRUCTIONS FOR FUTURE USE Know Your Air Compressor READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself
Dewalt DXCM201 | Instruction Manual - Page 11
English AIR INTAKE FILTER A The filter (A) is designed to clean air entering the pump. To ensure the pump continually receives a clean, cool, and dry air supply the filter must always be clean and the filter intake must be free from obstructions. AIR TANK DRAIN VALVE The drain valve (H) is
Dewalt DXCM201 | Instruction Manual - Page 12
carton should contain: • air compressor • handle • operator's manual • instruction sheet Check the compressor's specification label to ensure that you form in the pump and produce sludge in the oil, causing running parts to wear out prematurely. Excessive moisture is especially likely to occur if
Dewalt DXCM201 | Instruction Manual - Page 13
that a situation exists which if not avoided will result in death or serious injury. Check with a qualified electrician or serviceman when the grounding instructions are not completely understood, or when in doubt as to whether the product is properly grounded. Do not modify the plug provided; if it
Dewalt DXCM201 | Instruction Manual - Page 14
manual for safety, operation and maintenance instructions. Break-in Procedure NOTICE: Risk of property damage. Serious damage may result if the following break-in instructions are not closely followed. This procedure is required before the air compressor is put into service and when the check
Dewalt DXCM201 | Instruction Manual - Page 15
If the unit does not operate properly, SHUT DOWN IMMEDIATELY, and contact Product Service. 7. Check all air line fittings and connections/piping for air leaks by : When using regulator and other accessories refer to the manufacturers instructions. WARNING: Risk of bursting. If any unusual noise or
Dewalt DXCM201 | Instruction Manual - Page 16
you may be exposed to voltage sources, compressed air, or moving parts. Personal injuries can occur. Before performing any maintenance or repair, X Check for air leaks X* Clean compressor exterior X Remove tank from service X++ * To check for air leaks apply a solution of soapy water
Dewalt DXCM201 | Instruction Manual - Page 17
Checking Air Filter WARNING: Hot surfaces. Risk of burn. Tubes, pump head, and surrounding parts are very hot, do not touch (see the Hot Surfaces identified in Fig. 1). Allow compressor to cool prior to servicing. A dirty air filter will not allow the ST compressor to operate at full capacity
Dewalt DXCM201 | Instruction Manual - Page 18
English WARNING: Risk of bursting. Water will condense in the air tank. If not drained, water will corrode and weaken the air tank causing a risk of air tank rupture. NOTICE: Risk of property damage. Drain water from air tank may contain oil and rust which can cause stains. 6. After the water has
Dewalt DXCM201 | Instruction Manual - Page 19
. Hot surfaces. Risk of burn. Pump head, and surrounding parts are very hot, do not touch (see the Hot Surfaces identified in Fig. 1). Allow compressor to cool prior to servicing. 1. Set the Auto/Off lever to "OFF (O)", unplug the unit, and relieve all air pressure from the air tank. 2. Remove
Dewalt DXCM201 | Instruction Manual - Page 20
. Torque to 20-25 ft.-lbs (27.1-33.9 Nm) 9. Reinstall the outer belt guard. All moving parts must be guarded. Air Compressor Pump Intake and Exhaust Valves Once a year have a Trained Service Technician check the air compressor pump intake and exhaust valves. Inspect Air Lines and Fittings for Leaks
Dewalt DXCM201 | Instruction Manual - Page 21
Number Date and Place of Purchase Repairs To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by a DeWALT factory service center, a DeWALT authorized service center or other qualified service personnel. Always use identical replacement parts. 21
Dewalt DXCM201 | Instruction Manual - Page 22
repair information, call 1-(888)-895-4549 or visit dewalt.com. This warranty does not apply to accessories of ownership, with the exceptions noted below. Parts used in repair of whole goods or accessories of the Company set forth in the owner's manual, will render this warranty null and void. The
Dewalt DXCM201 | Instruction Manual - Page 23
, see engine manual for specific engine manufacturer's warranty coverage. Parts purchased separately: The warranty for parts purchased separately such components must be delivered, or shipped, to the nearest Authorized Service Center. All associated freight costs and travel charges must be
Dewalt DXCM201 | Instruction Manual - Page 24
English FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-888-895-4549 for a free replacement. HOT SURFACE. RISK OF BURNS. DO NOT TOUCH. SUPERFICIE CALIENTE. RIESGO DE QUEMADURAS. NO TOCAR. SUURFACE TRÈS CHAUDE. RISQUES DE BRÛLURES. NE PAS TOUCHER.
Dewalt DXCM201 | Instruction Manual - Page 25
English Troubleshooting Guide This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The operator or maintenance personnel can perform some corrective actions, and others may require the assistance of a qualified DeWALT technician or your
Dewalt DXCM201 | Instruction Manual - Page 26
4 5 6 7 8 9 10 11 12 13 Troubleshooting Codes POSSIBLE CAUSE POSSIBLE SOLUTION Fittings are not tight. explode. Leaking seals. Contact a DeWALT factory service center or a DeWALT authorized service center. Defective safety valve. Operate safety valve manually by pulling on ring. If valve
Dewalt DXCM201 | Instruction Manual - Page 27
center. Cylinder or piston damaged or worn. Contact a DeWALT factory service center or a DeWALT authorized service center. Compressor cylinder finish worn. Contact a DeWALT factory service center or a DeWALT authorized service center. Water in pump oil. Drain oil and refill pump with full
Dewalt DXCM201 | Instruction Manual - Page 28
. Inspect and replace transfer tubes or check valve, as required. Furnish adequate power. Replace check valve. Contact a DeWALT factory service center or a DeWALT authorized service center. Reduce to proper level. See Compressor Pump Oil under Maintenance. Relocate compressor to an area with cool