Dewalt DXPW1200-E Instruction Manual - Page 11

Accessories

Get Dewalt DXPW1200-E PDF manuals and user guides View all Dewalt DXPW1200-E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

&OHMJTI 4. Remove the high-pressure nozzle from the Y spray wand. Remove any obstructions with the nozzle cleaning tool (Y) provided and back flush with clean water. 5. Direct water supply into spray wand to back flush loosened particles for 30 seconds. 6. Reassemble the nozzle to the wand. 7. Reconnect spray wand to gun then turn on water supply. 8. Start pressure washer and place spray wand into high pressure setting to test. 5P$MFBOUIF8BUFS*OMFU'JMUFS This filter screen (U) should be checked periodically and cleaned if necessary. 1. Remove the filter screen (U) by grasping the end and removing it from water inlet of pump. 2. Clean filter by flushing it with water on both sides. 3. Reinsert filter into water inlet of pump. Cone side faces out. U NOTE: Do not operate pressure washer without filter properly installed. 4503"(& 1VNQ NOTICE: The manufacturer recommends using a pump protector/ winterizer when storing the unit for more than 30 days and/or when freezing temperatures are expected. FREEZE DAMAGE IS NOT COVERED BY THE WARRANTY. Pump protector/winterizer is usually available at the store where the pressure washer was purchased. If a pump protector/winterizer is not available, RV antifreeze needs to be run through the pump. NOTE: Using a pump protector/winterizer or RV antifreeze is to provide proper lubrication to the internal seals of the pump regardless of temperature or environment. 1SFTTVSF8BTIFS 1. Drain all water from high-pressure hose, coil it and store it in cradle of the pressure washer handle. 2. With nozzle pointed down and the spray gun and wand in a vertical position, squeeze trigger to drain all water from spray gun and wand. Store in gun holder. 3. Store chemical hose so it is protected from damage. 4. Store the machine and accessories in a dry, climate controlled environment. Do not store the machine or accessories in a place where the temperature could drop below 40 °F (4 °C). CAUTION: Risk of personal injury. Avoid placing hands between handle and frame when assembling to prevent pinching. NOTICE: Risk of property damage. Always store and transport unit in an upright position. ACCESSORIES Recommended accessories for use with your tool are available for purchase from your local dealer or authorized service center. If you need assistance in locating any accessory for your tool, please contact the FNA Group at www.dewaltpw.com, 1825 Greenleaf Avenue, Elk Grove Village, Il 60007, or call 1 (877) 362 4271. DANGER: Risk of fluid injection. When using replacement lances or guns with this pressure washer, DO NOT use a lance and/or lance/ gun combination that is shorter in length than what was provided with this pressure washer as measured from the nozzle end of the lance to the gun trigger. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
11
Pump protector/winterizer is usually available at the store where the
pressure washer was purchased. If a pump protector/winterizer is not
available, RV antifreeze needs to be run through the pump.
NOTE:
Using a pump protector/winterizer or RV antifreeze is to
provide proper lubrication to the internal seals of the pump regardless
of temperature or environment.
1. Drain all water from high-pressure hose, coil it and store it in
cradle of the pressure washer handle.
2. With nozzle pointed down and the spray gun and wand in a
vertical position, squeeze trigger to drain all water from spray gun
and wand. Store in gun holder.
3. Store chemical hose so it is protected from damage.
4. Store the machine and accessories in a dry, climate controlled
environment. Do not store the machine or accessories in a place
where the temperature could drop below 40 °F (4 °C).
CAUTION:
Risk of personal injury. Avoid placing hands between
handle and frame when assembling to prevent pinching.
NOTICE:
Risk of property damage. Always store and transport unit
in an upright position.
ACCESSORIES
Recommended accessories for use with your tool are available for
purchase from your local dealer or authorized service center. If you
need assistance in locating any accessory for your tool, please contact
the FNA Group at www.dewaltpw.com, 1825 Greenleaf Avenue, Elk
Grove Village, Il 60007, or call 1 (877) 362 4271.
DANGER:
Risk of fluid injection. When using replacement lances
or guns with this pressure washer, DO NOT use a lance and/or lance/
gun combination that is shorter in length than what was provided with
this pressure washer as measured from the nozzle end of the lance to
the gun trigger.
4. Remove the high-pressure nozzle from the
Y
spray wand. Remove any obstructions with
the nozzle cleaning tool (Y) provided and
back flush with clean water.
5. Direct water supply into spray wand to
back flush loosened particles for 30
seconds.
6. Reassemble the nozzle to the wand.
7. Reconnect spray wand to gun then turn on water supply.
8. Start pressure washer and place spray wand into high pressure
setting to test.
This filter screen (U) should be checked periodically and cleaned if
necessary.
1. Remove the filter screen (U) by grasping the
U
end and removing it from water inlet of pump.
2. Clean filter by flushing it with water on both
sides.
3. Reinsert filter into water inlet of pump. Cone
side faces out.
NOTE:
Do not operate pressure washer without
filter properly installed.
NOTICE:
The manufacturer recommends using a pump protector/
winterizer when storing the unit for more than 30 days and/or when
freezing temperatures are expected.
FREEZE DAMAGE IS NOT
COVERED BY THE WARRANTY.