Dewalt DXPW1200-E Instruction Manual - Page 6

Operation, Save These Instructions, For Future Use, Installation

Get Dewalt DXPW1200-E PDF manuals and user guides View all Dewalt DXPW1200-E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

&OHMJTI SAVE THESE INSTRUCTIONS FOR FUTURE USE INSTALLATION 1SFTTVSF8BTIFS"TTFNCMZ 'JH 1. Place handle (G) onto frame (F) and secure with saddle bolts and knobs (R). CAUTION: Risk of personal injury. Avoid placing hands between handle and frame when G assembling to prevent pinching. 2. Attach high-pressure hose (H) to spray gun (C). Make sure it is secure. R F 3. Connect wand (E) to spray gun (C). Make sure connection is secure. C H E C 4. Place the nozzle holder (B) onto the panel assembly (A) and push each nozzle holder into place. 5. Remove the five colored quick- B connect nozzles from the plastic bag and insert them into A correct grommet on the nozzle holder. Nozzles are color coded to match colored nozzles on panel assembly. NOTE: The high-pressure pump was filled with oil at the factory. Always check oil level before using (refer to Maintenance for more information). WARNING: Risk of bursting. Use a tire pressure gauge to check the tires pressure before each use and while inflating tires; see the tire sidewall for the correct tire pressure. NOTE: Air tanks, compressors and similar equipment used to inflate tires can fill small tires similar to these very rapidly. Adjust pressure regulator on air supply to no more than the rating of the tire pressure. Add air in small increments and frequently use the tire gauge to prevent over inflation. OPERATION 1SFTTVSF"EKVTUNFOUT 'JH The pressure setting is preset at the factory to achieve optimum pressure and cleaning. To lower the pressure, follow these instructions. 1. Back away from the surface to be cleaned. The further away you are, the less the pressure will be on the surface to be cleaned. 2. Change to the 40˚ nozzle (white). This nozzle delivers a less powerful stream of water and a wider spray pattern. Refer to Spray Wand Nozzles. 3. Water pressure can be varied by turning the pressure adjusting knob (L) clockwise to increase pressure and counterclockwise to decrease pressure. NOTICE: DO NOT attempt to increase pump pressure. A higher pressure setting than the factory set pressure may damage pump. 4QSBZ8BOE/P[[MFT 'JH The nozzles for the spray wand are stored in the nozzle holder (B) on the panel assembly (A). Colors on the panel identify nozzle location and spray pattern. Refer to the following chart to choose the correct nozzle for the job to be performed. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
6
NOTE:
The high-pressure pump was filled with oil at the factory.
Always check oil level before using (refer to
Maintenance
for more
information).
WARNING:
Risk of bursting.
Use a tire pressure gauge to check the
tires pressure before each use and while inflating tires; see the tire sidewall
for the correct tire pressure.
NOTE:
Air tanks, compressors and similar equipment used to inflate
tires can fill small tires similar to these very rapidly. Adjust pressure
regulator on air supply to no more than the rating of the tire pressure.
Add air in small increments and frequently use the tire gauge to
prevent over inflation.
OPERATION
The pressure setting is preset at the factory to achieve optimum
pressure and cleaning. To lower the pressure, follow these instructions.
1. Back away from the surface to be cleaned. The further away you
are, the less the pressure will be on the surface to be cleaned.
2. Change to the 40˚ nozzle (white). This nozzle delivers a less
powerful stream of water and a wider spray pattern. Refer to
Spray Wand Nozzles
.
3. Water pressure can be varied by turning the pressure adjusting
knob (L) clockwise to increase pressure and counterclockwise to
decrease pressure.
NOTICE:
DO NOT attempt to increase pump pressure. A higher
pressure setting than the factory set pressure may damage pump.
The nozzles for the spray wand are stored in the nozzle holder (B) on the
panel assembly (A). Colors on the panel identify nozzle location and spray
pattern. Refer to the following chart to choose the correct nozzle for
the job to be performed.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE
INSTALLATION
1. Place handle (G) onto frame (F) and secure
R
F
G
with saddle bolts and knobs (R).
CAUTION:
Risk of personal injury. Avoid
placing hands between handle and frame when
assembling to prevent pinching.
2. Attach high-pressure hose (H) to spray gun
(C). Make sure it is secure.
3. Connect wand (E) to spray gun (C). Make sure
connection is secure.
E
H
C
C
4. Place the nozzle holder (B) onto the panel assembly (A) and push
each nozzle holder into place.
5. Remove
the
five
B
A
colored
quick-
connect nozzles from
the plastic bag and
insert
them
into
correct grommet on
the nozzle holder.
Nozzles are color coded to match colored nozzles
on panel assembly.