Dymo 1761334 Technical Reference - Page 2

Copyright, Trademarks, Description: Direct Thermal Printer, Model: LabelWriter SE450, Certification

Get Dymo 1761334 PDF manuals and user guides View all Dymo 1761334 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

Copyright © 2010 Sanford, L.P. All rights reserved. Revised 7/26/2010. No part of this document or the software may be reproduced or transmitted in any form or by any means or translated into another language without the prior written consent of Sanford, L.P. Trademarks LabelWriter and DYMO are trademarks or registered trademarks of Sanford, L.P. All other trademarks are the property of their respective holders. Description: Direct Thermal Printer Model: LabelWriter SE450 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC (Federal Communications Committee) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correcting the interference by one or more of the following measures: n Reorient the receiving antenna. n Increase the separation between the equipment and the receiver. n Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. n Use shielded cables to connect this device to computers. n Consult the dealer or an experienced radio/TV technician for help. n Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment and void the manufacturer's warranty. Certification This device has been tested and complies with the requirements of: UL 1950 EN60950: Low Voltage Directive Product Safety FCC Part 15 Class B EN55022: Radiated and Conducted Emissions B EN50082-1: Generic Immunity ESD, RF, and Transient Susceptibility i

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Copyright
© 2010 Sanford, L.P. All rights reserved. Revised 7/26/2010.
No part of this document or the software may be reproduced or transmitted in any form or
by any means or translated into another language without the prior written consent of
Sanford, L.P.
Trademarks
LabelWriter and DYMO are trademarks or registered trademarks of Sanford, L.P. All other
trademarks are the property of their respective holders.
Description: Direct Thermal Printer
Model: LabelWriter SE450
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC (Federal Communications Committee) rules. These
limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency
energy, and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try correcting
the interference by one or more of the following measures:
n
Reorient the receiving antenna.
n
Increase the separation between the equipment and the receiver.
n
Connect the equipment to an outlet on a circuit different from that to which the receiver
is connected.
n
Use shielded cables to connect this device to computers.
n
Consult the dealer or an experienced radio/TV technician for help.
n
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment and void the
manufacturer’s warranty.
Certification
This device has been tested and complies with the requirements of:
UL 1950
EN60950: Low Voltage Directive Product Safety
FCC Part 15 Class B
EN55022: Radiated and Conducted Emissions B
EN50082-1: Generic Immunity ESD, RF, and Transient Susceptibility
i