Dymo 1761334 Technical Reference - Page 71

Configuration Menu

Get Dymo 1761334 PDF manuals and user guides View all Dymo 1761334 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Chapter 5 Configuration Menu The LabelWriter SE450 printer has a Printer Configuration Menu built into the firmware. Through this menu, flash memory settings such as baud rate and feed distance can be changed. Flash memory settings remain in effect even after power has been removed from the printer. The Printer Configuration Menu is accessible by using any terminal communications (modem) program (such as, Hyperterminal in Windows) and communicating with the printer through an RS-232 serial port. The communications software MUST be configured to operate as follows: 9600 baud, no parity, 8 data bits, and 1 stop bit To access the Printer Configuration menu 1. Load labels in the printer and connect the serial cable. 2. Disconnect power to the printer. 3. Press and hold down the form feed button. 4. While the form feed button is pressed, connect the power cord. 5. Continue to hold the form feed button down for five more seconds. The green light will blink. 6. Release the feed button. 7. Start your communications software. 8. Press until the menu appears. Dymo LabelWriter SE450 Firmware Version 1765303v0G Printer Configuration Menu Type ? for help 9. Press ? for help. You should see the following on your screen: -? B? Display Baud Rate B0 Set 1200 Baud B1 Set 2400 Baud B2 Set 4800 Baud B3 Set 9600 Baud 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Configuration Menu
The LabelWriter SE450 printer has a Printer Configuration Menu built into the firmware.
Through this menu, flash memory settings such as baud rate and feed distance can be
changed. Flash memory settings remain in effect even after power has been removed from
the printer.
The Printer Configuration Menu is accessible by using any terminal communications
(modem) program (such as, Hyperterminal in Windows) and communicating with the printer
through an RS-232 serial port. The communications software MUST be configured to
operate as follows:
9600 baud, no parity, 8 data bits, and 1 stop bit
To access the Printer Configuration menu
1.
Load labels in the printer and connect the serial cable.
2.
Disconnect power to the printer.
3.
Press and hold down the form feed button.
4.
While the form feed button is pressed, connect the power cord.
5.
Continue to hold the form feed button down for five more seconds. The green light will
blink.
6.
Release the feed button.
7.
Start your communications software.
8.
Press <Enter> until the menu appears.
Dymo LabelWriter SE450
Firmware Version 1765303v0G
Printer Configuration Menu
Type ? for help
9.
Press ? for help.
You should see the following on your screen:
-?
B? Display Baud Rate
B0 Set 1200 Baud
B1 Set 2400 Baud
B2 Set 4800 Baud
B3 Set 9600 Baud
65
Chapter 5