EMC DS-5100B Hardware Reference

EMC DS-5100B - Connectrix Switch - 8Gb Fibre Channel Manual

Get EMC DS-5100B - Connectrix Switch - 8Gb Fibre Channel PDF manuals and user guides View all EMC DS-5100B manuals
Add to My Manuals
Save this manual to your list of manuals

EMC DS-5100B manual content summary:

  • EMC DS-5100B | Hardware Reference - Page 1
    53-1000854-02 July 18, 2008 Brocade 5100 Hardware Reference Manual
  • EMC DS-5100B | Hardware Reference - Page 2
    the licensing terms applicable to the open source software, and obtain a copy of the programming source code, please visit http://www.brocade.com/support/oscd. Brocade Communications Systems, Incorporated Corporate Headquarters Brocade Communications Systems, Inc. 1745 Technology Drive San Jose
  • EMC DS-5100B | Hardware Reference - Page 3
    Brocade 5100 overview 1 Port side of the Brocade 5100 2 Non-port side of the Brocade 5100 4 Field replaceable units (FRUs 4 Ports on Demand license 5 ISL trunking groups 5 Chapter 2 Brocade Brocade 5100 9 Cabinet installation for a Brocade 5100 10 Brocade 5100 Hardware Reference Manual
  • EMC DS-5100B | Hardware Reference - Page 4
    Facility requirements 28 Power supply specifications 28 Environmental requirements 29 General specifications 29 Data transmission ranges 30 Memory specifications 31 Fibre Channel port specifications 31 Serial port specifications 32 iv Brocade 5100 Hardware Reference Manual 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 5
    Index Regulatory compliance 32 FCC warning (US only 33 MIC statement (Republic of Korea 33 VCCI statement Japan 33 Power cords (Japan Denan 33 BSMI statement (Taiwan 34 CE statement 34 Canadian requirements 34 Laser compliance 35 RTC battery 35 Electrical safety 35 Regulatory
  • EMC DS-5100B | Hardware Reference - Page 6
    vi Brocade 5100 Hardware Reference Manual 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 7
    and hardware configurations are tested and supported by Brocade Communications Systems, Inc. for Fabric OS v6.1.0, documenting all possible configurations and scenarios is beyond the scope of this document. This document is specific to the Brocade 5100 and Fabric OS v6.1.0. To obtain information
  • EMC DS-5100B | Hardware Reference - Page 8
    this guide are presented in mixed lettercase: for example, switchShow. In actual examples, command lettercase is often all lowercase. Otherwise, this manual specifically notes Elements are exclusive. Example: --show -mode egress | ingress viii Brocade 5100 Hardware Reference Manual 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 9
    notices and statements are used in this manual. They are listed below in order of statement indicates potential damage to hardware or data. CAUTION A Caution statement alerts you definitions specific to Brocade and Fibre Channel, see the Brocade Glossary. For definitions of SAN-specific terms
  • EMC DS-5100B | Hardware Reference - Page 10
    are also bundled with the Fabric OS firmware. Other industry resources • White papers, online demos, and data sheets are available through the Brocade Web site at http://www.brocade.com/products/software.jhtml. • Best practice guides, white papers, data sheets, and other documentation is available
  • EMC DS-5100B | Hardware Reference - Page 11
    Brocade 200E-On the non-port side of the chassis • Brocade 300, 4100, 4900, 5100, 5300, 7500, and Brocade Encryption Switch-On the switch switch • Brocade 7600-On the bottom of the chassis • Brocade 48000-Inside the chassis next to the power supply bays • Brocade Brocade [email protected]
  • EMC DS-5100B | Hardware Reference - Page 12
    xii Brocade 5100 Hardware Reference Manual 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 13
    storage for firmware updates, output of the supportSave command and storage for configuration uploads and downloads • Single motherboard design with 667 MHz PowerPC 440EPx Reduced Instruction Set Computer (RISC) CPU and integrated peripherals which provide high performance. Brocade 5100 Hardware
  • EMC DS-5100B | Hardware Reference - Page 14
    and broadcast data traffic type, are support. • Brocade Small Form-Factor Pluggable (SFP) or SFP+ optical transceivers support any combination of Short Wavelength (SWL), Long Wavelength (LWL) or Extended Long Wavelength (ELWL) optical media among the switch ports. • Brocade Fabric Operating System
  • EMC DS-5100B | Hardware Reference - Page 15
    (top) and power (bottom) LEDs 2 System RS232 console port (RJ-45) 3 System Ethernet port (RJ-45) 4 Ethernet port LEDs (green/amber) 5 USB port 6 Fibre Channel port status LED 7 Fibre Channel ports 8 Switch ID pull-out tab FIGURE 1 Port-side view of the Brocade 5100 Port Numbering
  • EMC DS-5100B | Hardware Reference - Page 16
    side of the Brocade 5100 ATTENTION Brocade ISL Trunking is licensed software that allows you to create trunking groups of ISLs between adjacent switches. For more information about Brocade ISL Trunking, refer to the Brocade Fabric OS Administrator's Guide. Non-port side of the Brocade 5100 The non
  • EMC DS-5100B | Hardware Reference - Page 17
    and re-enable the switch to activate all ports simultaneously. For detailed information on enabling additional ports using the POD license, refer to the Fabric OS Administrator's Guide. ISL trunking groups The Brocade 5100 supports Interswitch Link (ISL) Trunking as a licensed feature. When this
  • EMC DS-5100B | Hardware Reference - Page 18
    1 ISL trunking groups 6 Brocade 5100 Hardware Reference Manual 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 19
    ft. Power Cord • Rubber feet, required for setting up the switch as a standalone unit • Brocade Family Doc CD • Brocade 5100 QuickStart Guide • switches. The optional mid-mount rack kit for switches can be ordered from your switch retailer. Brocade 5100 Hardware Reference Manual 7 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 20
    specified by the electrical rating on the switch nameplate. • The power supply standards provided in Table 5, "Power Supply Specifications" on page 28 are met. Environmental full tensile load and 1.2 inches with no tensile load. 8 Brocade 5100 Hardware Reference Manual 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 21
    bend radius. • If you are using Brocade ISL Trunking, consider grouping cables by trunking groups. The cables used in trunking groups must meet specific requirements, as described in the Fabric OS Administrator's Guide. • For easier maintenance, label the fiber optic cables and record the devices to
  • EMC DS-5100B | Hardware Reference - Page 22
    can also use the Brocade 5100 Quick Start Guide. If you do not want to use EZSwitchSetup, follow the instructions in the rest of this section. Providing power to the switch Perform the following steps to provide power to the Brocade 5100. 1. Connect the power cords to both power supplies, and then
  • EMC DS-5100B | Hardware Reference - Page 23
    Brocade 5100 configuration 2 3. After POST is complete, verify that the switch power and status LEDs on the left of the port side of the switch are green. Creating a serial connection You will perform all basic configuration tasks in this guide using a serial connection. Complete the following
  • EMC DS-5100B | Hardware Reference - Page 24
    zone on a switch updates the local time zone setup and is reflected in local time calculations. • By default, all switches are in the GMT time zone (0,0). If all switches in a fabric are in one time zone, it is possible for you to keep the time zone setup at the default setting. 12 Brocade 5100
  • EMC DS-5100B | Hardware Reference - Page 25
    in the payload and will update only the active server address. If the active NTP server configured is IPv6, then distributing the same in the fabric will not be possible to switches earlier than v5.3.0 because IPv6 is supported for Fabric OS version 5.3.0 and later. The default value LOCL will be
  • EMC DS-5100B | Hardware Reference - Page 26
    into the switch using the default password, which is password. 2. Enter the tsClockServer command: switch:admin> default, this value is LOCL, which uses the local clock of the principal or primary switch as the clock server. switch:admin> tsclockserver 14 Brocade 5100 Hardware Reference Manual
  • EMC DS-5100B | Hardware Reference - Page 27
    "10.32.170.1;10.32.170.2;ntp.localdomain.net" Updating Clock Server configuration...done. Updated with the NTP servers Changes to the clock server value on the principal or primary FCS switch are propagated to all switches in the fabric Brocade 5100 Hardware Reference Manual 15 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 28
    2 Brocade 5100 configuration 16 Brocade 5100 Hardware Reference Manual 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 29
    as soon as the first power supply is connected and powered on. The switch runs POST by default each time it is powered on; it can take up to several minutes to boot and complete POST. To power the Brocade 5100 off, power off both power supplies by setting each AC power switch to "O". All devices are
  • EMC DS-5100B | Hardware Reference - Page 30
    ) 2 Ethernet port Status LEDs (green/amber) 3 FC port status (port 9) Figure 5 shows the non-port side LEDs on the Brocade 5100. 1 2 FIGURE 5 Brocade 5100 non-port side LEDs 1 Power supply status LED 2 Power supply status LED 18 Brocade 5100 Hardware Reference Manual 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 31
    switch. TABLE 1 Brocade 5100 LED Patterns During Normal Operation LED Name LED Color Status of Hardware Recommended Action Power Supply No light Status (right) Primary power cord is disconnected or is not actively powered, or power Technical Support. Steady green System is on and power
  • EMC DS-5100B | Hardware Reference - Page 32
    Technical Support if required. Steady amber (for more than five seconds) Port is receiving light or signal carrier No action required. at 4 Gbps; but is not yet online. POST and boot specifications When the switch is turned on or rebooted, the switch performs POST. Total boot time with POST can
  • EMC DS-5100B | Hardware Reference - Page 33
    to other switches, the switch participates in a fabric configuration. 4. Obtains a domain ID and assigning port addresses. 5. Constructs unicast routing tables. 6. Enables normal port operation. Interpreting POST results POST is a system check that is performed each time the switch is powered on
  • EMC DS-5100B | Hardware Reference - Page 34
    Brocade 5100 only supports Brocade-branded SFPs. If you use an unqualified SFP, the switchShow command output shows the port in a Mod_Inv state. Fabric tests In addition to POST, the Fabric OS includes diagnostic tests to help you troubleshoot the hardware and firmware. This includes tests of
  • EMC DS-5100B | Hardware Reference - Page 35
    specific diagnostic tests, refer to the Fabric OS Troubleshooting and Diagnostics Guide. Field Replaceable Units (FRUs) The power instructions are provided with all replacement units ordered. Power supply/fan assembly FRU replacement The Brocade 5100 fans are fixed inside the integrated power
  • EMC DS-5100B | Hardware Reference - Page 36
    the error log. For more information about POST, see "POST and boot specifications" on page 20. For information about upgrading the version of Fabric OS installed on your switch, refer to the Fabric OS Administrator's Guide. You can manage the Brocade 5100 using any of the management options listed
  • EMC DS-5100B | Hardware Reference - Page 37
    Managing the Brocade 5100 3 NOTE To achieve in-band support for IP over Fibre Channel, the software must be run on both the HBA and the switch, and it must be supported by both the HBA and HBA driver. Brocade 5100 Hardware Reference Manual 25 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 38
    3 Managing the Brocade 5100 26 Brocade 5100 Hardware Reference Manual 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 39
    • 40 port LEDs, 1 switch power LED, 1 switch status LED, 2 Ethernet LEDs, and 2 power supply LEDs • One USB port for system log file downloads or firmware upgrades • Two universal AC input and redundant power supplies with AC switches and built-in fans Brocade 5100 Hardware Reference Manual 27 53
  • EMC DS-5100B | Hardware Reference - Page 40
    , pushing air towards the port side of the switch. Table 5 lists the power supply specifications for the Brocade 5100. TABLE 5 Power Supply Specifications Specification Value Inlet Maximum output of one power supply C13 125 Watts 28 Brocade 5100 Hardware Reference Manual 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 41
    lists the general specifications for the Brocade 5100. TABLE 7 General Specifications Specification Description Configurable port types System architecture System processor ANSI Fibre Channel protocol E_Port, F_Port, FL_Port, M_Port, and EX_Port Nonblocking shared-memory switch Power PC 440EPX
  • EMC DS-5100B | Hardware Reference - Page 42
    A Data transmission ranges TABLE 7 General Specifications Specification Description Aggregate switch I/O bandwidth Port-to-port latency 640 Gbps if all 40 ports are running at 8 Gbps, full duplex 700 nanoseconds Table 8 lists the EMC (electromagnetic compatibility) for the Brocade 5100. TABLE
  • EMC DS-5100B | Hardware Reference - Page 43
    Memory specifications A TABLE 9 Port Speed 2 Gbps 4 Gbps 8 Gbps Laser Data Transmission Ranges Cable Brocade Extended Fabrics license; 50 to 100 km with a Brocade Extended Fabrics license 40 km (24.8 miles) NA NA NA NA NA NA NA NA NA NA 10 km NA Memory specifications The Brocade
  • EMC DS-5100B | Hardware Reference - Page 44
    before connecting the switch to a fabric or IP network. The serial port's parameters are fixed at 9600 baud, 8 data bits, and no parity, with flow control set to None. This connector is for initial IP address configuration and for recovery of the switch to its factory default settings if Flash
  • EMC DS-5100B | Hardware Reference - Page 45
    and if not installed and used in accordance with the instruction manual, might cause harmful interference to radio communications. Operation of When such trouble occurs, the user might be required to take corrective actions. Power cords (Japan Denan) Brocade 5100 Hardware Reference Manual 33
  • EMC DS-5100B | Hardware Reference - Page 46
    BSMI Statement is applicable to Brocade 5100 power supplies. CE statement ATTENTION Spec) • EN61000-3-3 Canadian requirements This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations, ICES-003 Class A. 34 Brocade 5100 Hardware Reference Manual
  • EMC DS-5100B | Hardware Reference - Page 47
    real-time clock begins to lose time. Electrical safety ATTENTION This switch might have more than one power cord. To reduce the risk of electric shock, disconnect both power cords before servicing. ATTENTION Connect the power cord only to a grounded outlet. ATTENTION This product is designed for
  • EMC DS-5100B | Hardware Reference - Page 48
    and GB9254-1998 or latest CNS 14336(94) or latest EMC EN55022 or CISPR22 or AS/NZS CISPR22 51318.22-99 requirements for the Brocade 5100 switch. China RoHS The manual of the product. EPUP EPUP FRU Brocade Brocade CD Br ocade EPUP 36 Brocade 5100 Hardware Reference Manual
  • EMC DS-5100B | Hardware Reference - Page 49
    O O O Switch Fan, Blower X O O O O O assemblies PCBA cards X O O O O O Power Supply kit X O O O O O SFPs (optical X O O O O O cable connectors) Sheet Metal X O is within the aforementioned limits. Brocade 5100 Hardware Reference Manual 37 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 50
    A Environmental regulation compliance 38 Brocade 5100 Hardware Reference Manual 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 51
    supported, 29 Fibre Channel ports specifications, 31 Field replaceable units (FRUs), 4 front panel LEDs, 17 I installing a Brocade 5100 into an EIA cabinet, 10 installing a stand-alone Brocade 5100, 9 installing an SFP, 22 interpreting POST results, 21 IP over Fibre Channel (FC-IP), 29 ISL trunking
  • EMC DS-5100B | Hardware Reference - Page 52
    of switch, 28 port configurable types, 29 Ethernet port, 27 Fibre Channel port, 31 serial port, 27, 32 trunking, 4, 5 port numbering, 3 port status LEDs, 17 Ports On Demand, 5 ports, enabling, 5 ports, numbering, 3 POST error messages, 21 interpreting, 21 POST and boot specifications, 20 power
  • EMC DS-5100B | Hardware Reference - Page 53
    V VCCI statement, 33 W weight, switch, 28 Brocade 5100 Hardware Reference Manual 41 53-1000854-02
  • EMC DS-5100B | Hardware Reference - Page 54
    42 Brocade 5100 Hardware Reference Manual 53-1000854-02
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
53-1000854-02
July 18, 2008
Brocade 5100
Hardware Reference Manual