Electrolux EI27EW45PS Complete Owner's Guide (English) - Page 39

UPPER OVEN, broil, START enter.

Get Electrolux EI27EW45PS PDF manuals and user guides View all Electrolux EI27EW45PS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Before You Call 39 Oven control panel chimes and • displays an F code error. Soil not completely removed after • fresh clean. • • • Appliance is not level. • • • Fan noise occurring after the oven is • turned off. Oven control has detected a fault or error condition. Press STOP to clear the error code. Try bake or broil function. If the F code error repeats, turn off power to appliance, wait 5 minutes and then repower appliance. Set clock with correct time of day. Try bake or broil function again. If fault recurs, press STOP to clear. Fresh clean was interrupted. Review "Fresh Clean" on page 31. Excessive spills on oven bottom. Clean before starting fresh clean. Failure to clean soil from the oven frame, the door liner outside the oven door gasket, and the small area at the front center of the oven bottom. These areas are not in the fresh cleaning area, but they get hot enough to burn on residue. Clean these areas before starting the fresh clean cycle. Burned-on residue can be cleaned with a stiff nylon brush and water or a nylon scrubber. Be careful not to damage the oven gasket. If your oven is cooking poorly, perform the following check: Press UPPER OVEN, press broil, then press START enter. Place your hand near the handle on the oven door. Between the door and the control panel you should feel a rush of air on your hand. If so, your unit is functioning properly and you have had a power failure in your home. If no air rush happens, call a service technician to replace your cooling fan. Poor installation. Place oven rack in center of oven. Place a level on the oven rack. Adjust leveling leg at base of appliance until the oven rack is level. Kitchen cabinet alignment may make oven appear not level. Be sure cabinets are square and have sufficient room for appliance clearance. Cabinets not square or are built in too tightly. Contact builder or installer to make appliance accessible. Some models are equipped with a cooling fan that runs during the cooking process to cool internal electronic components. It is normal for this fan to continue to run for an extended period of time, even when the oven is off.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Before You Call
39
Oven control panel chimes and
displays an F code error.
•
Oven control has detected a fault or error condition. Press
STOP
to clear the error code.
Try bake or broil function. If the F code error repeats, turn off power to appliance, wait 5
minutes and then repower appliance. Set clock with correct time of day. Try bake or broil
function again. If fault recurs, press
STOP
to clear.
Soil not completely removed after
fresh clean.
•
Fresh clean was interrupted. Review
“Fresh Clean”
on
page 31
.
•
Excessive spills on oven bottom. Clean before starting fresh clean.
•
Failure to clean soil from the oven frame, the door liner outside the oven door gasket,
and the small area at the front center of the oven bottom. These areas are not in the
fresh cleaning area, but they get hot enough to burn on residue. Clean these areas
before starting the fresh clean cycle. Burned-on residue can be cleaned with a stiff nylon
brush and water or a nylon scrubber. Be careful not to damage the oven gasket.
•
If your oven is cooking poorly, perform the following check: Press
UPPER OVEN
, press
broil,
then press
START enter.
Place your hand near the handle on the oven door.
Between the door and the control panel you should feel a rush of air on your hand. If so,
your unit is functioning properly and you have had a power failure in your home. If no air
rush happens, call a service technician to replace your cooling fan.
Appliance is not level.
•
Poor installation. Place oven rack in center of oven. Place a level on the oven rack.
Adjust leveling leg at base of appliance until the oven rack is level.
•
Kitchen cabinet alignment may make oven appear not level. Be sure cabinets are
square and have sufficient room for appliance clearance.
•
Cabinets not square or are built in too tightly. Contact builder or installer to make
appliance accessible.
Fan noise occurring after the oven is
turned off.
•
Some models are equipped with a cooling fan that runs during the cooking process to
cool internal electronic components. It is normal for this fan to continue to run for an
extended period of time, even when the oven is off.