Electrolux EIED55HIW Installation Instructions (All Languages) - Page 15

Water connection Steam Model only - washer and dryer

Get Electrolux EIED55HIW - 8.0 cu. Ft. Electric Dryer PDF manuals and user guides
UPC - 012505378614
View all Electrolux EIED55HIW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Installation Instructions 15 Water connection (Steam Model only) WATER SUPPLY REQUIREMENTS Cold water faucet MUST be installed within 42 inches (107 cm) of your dryer's water inlet. The faucet MUST be 3/4 inch (1.9 cm) with threading for laundry hose connection. Water pressure MUST be between 30 and 120 psi. Your water department can advise you of your water pressure. 1. Turn off COLD water supply to washer, 2. Remove COLD inlet hose from COLD water supply and inspect for rubber washer. Replace washer if it is torn or worn out. RUBBER WASHER MUST BE PRESENT AND UNDAMAGED COLD INLET HOSE TO WASHER 3. Momentarily turn on COLD supply and run some water into a bucket or container to clear any contaminants in the line. 4. Remove hose kit from dryer drum and inspect hose couplings for proper placement of rubber washers. RUBBER WASHERS MUST BE PRESENT

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
15
Water connection (Steam Model only)
Installation Instructions
Turn off COLD water supply to washer,
1.
Remove COLD inlet hose from COLD water
2.
supply and inspect for rubber washer. Replace
washer if it is torn or worn out.
Momentarily turn on COLD supply and run
3.
some water into a bucket or container to clear
any contaminants in the line.
Remove hose kit from dryer drum and inspect
4.
hose couplings for proper placement of rubber
washers.
RUBBER WASHER
MUST BE PRESENT
AND UNDAMAGED
COLD INLET HOSE
TO WASHER
RUBBER WASHERS
MUST BE PRESENT
WATER SUPPLY REQUIREMENTS
Cold water faucet MUST be installed within 42
inches (107 cm) of your dryer’s water inlet. The
faucet MUST be 3/4 inch (1.9 cm) with thread-
ing for laundry hose connection. Water pressure
MUST be between 30 and 120 psi. Your water
department can advise you of your water pressure.