Electrolux EIED55HIW Installation Instructions (All Languages) - Page 17

General installation - review

Get Electrolux EIED55HIW - 8.0 cu. Ft. Electric Dryer PDF manuals and user guides
UPC - 012505378614
View all Electrolux EIED55HIW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Installation Instructions 17 General installation 1. Connect the exhaust duct to the outside exhaust system (see pages 5 through 7). Use of a 4" (102 mm) clamp (item A) is recommended to connect the dryer to the exhaust vent system. Use metal foil tape to seal all other joints. 2. Carefully slide the dryer to its final position. Adjust one or more of the legs until the dryer is resting solidly on all four legs. Place a level on top of the dryer. The dryer MUST be level and A resting solidly on all four legs. Rock alternating corners to check for stability. Remove and discard door tape. IMPORTANT Be sure the power is off at a circuit breaker/fuse box before plugging the power cord into an outlet. 3. Plug the power cord into a grounded outlet. 4. Turn on the power at the circuit breaker/fuse box. 5. Read the Use & Care Guide provided with the dryer. It contains valuable and helpful information that will save you time and money. 6. See the next page about performing a brief, helpful "Installation Cycle" for your new dryer. 7. If you have any questions during initial operation, please review the "Avoid Service Checklist" in your Use & Care Guide before calling for service. 8. Place these instructions in a location near the dryer for future reference. NOTE A wiring diagram and technical data sheet are located inside the dryer console. Grounding type wall receptacle Do not, under any circumstances, cut, remove, or bypass the grounding prong. Power cord with 3-prong grounded plug

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
17
General installation
NOTE
A wiring diagram and technical data sheet are
located inside the dryer console.
Grounding type
Grounding type
wa
wa
ll receptacl
ll receptacl
e
Po
Po
wer cord with
wer cord with
3-prong
3-prong
gr
gr
ounded plug
ounded plug
Do not,
Do not,
under
under
an
an
y cir
y cir
cumstances,
cumstances,
cut,
cut,
remo
remo
ve
ve
,
or b
or b
ypass th
ypass th
e
gr
gr
ounding pr
ounding pr
ong.
ong.
IMPORTANT
Be sure the power is off at a circuit breaker/fuse
box before plugging the power cord into an outlet.
Connect the exhaust duct to the outside exhaust
1.
system (see pages 5 through 7). Use of a 4” (102
mm) clamp (item A)
is recommended to connect
the dryer to the exhaust vent system. Use metal
foil tape to seal all other joints.
Carefully slide the dryer to its final position.
2.
Adjust one or more of the legs until the dryer is
resting solidly on all four legs. Place a level on
top of the dryer. The dryer MUST be level and
resting solidly on all four legs. Rock alternating
corners to check for stability. Remove and
discard door tape.
Plug the power cord into a grounded outlet.
3.
Turn on the power at the circuit breaker/fuse
4.
box.
Read the
5.
Use & Care Guide
provided with
the dryer. It contains valuable and helpful
information that will save you time and money.
See the next page about performing a brief,
6.
helpful “Installation Cycle” for your new dryer.
If you have any questions during initial
7.
operation, please review the “Avoid Service
Checklist” in your
Use & Care Guide
before
calling for service.
Place these instructions in a location near the
8.
dryer for future reference.
Installation Instructions
A