Electrolux EIED55HIW Installation Instructions (All Languages) - Page 19

Reversing Door

Get Electrolux EIED55HIW - 8.0 cu. Ft. Electric Dryer PDF manuals and user guides
UPC - 012505378614
View all Electrolux EIED55HIW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Reversing Door 19 Preparing to reverse door swing 1 Be sure you have adequate swing area before reversing door. 2 You will need a screw driver with a #2 square bit. 3 Protect flat work surface, such as top of dryer or floor near dryer, with a soft cloth or towel. 4 Be sure dryer is unplugged from power source! WARNING ELECTRICAL SHOCK HAZARD Failure to disconnect power source before servicing could result in personal injury or even death. Removing door and hardware Tools needed: Screwdrivers with #2 square & straight bit A) Removing Trim Ring 1 Open door to 90 degree angle. 2 Remove and save trim plug and long, course-thread, panhead screw. B) Removing Door from Hinge 1 Reopen door to 90 degree angle. 2 Remove 4 long, course-thread, counter-sunk hinge screws from door. 3 Close door. 4 Rotate door trim approximately ¾" counterclockwise and pull ring away from door. 3 While supporting the weight of the door with both hands, separate the door from the hinge. 4 Gently place door face down on flat, covered work surface.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
19
Reversing Door
1
Be sure you have adequate swing area before reversing door.
2
You will need a screw driver with a #2 square bit.
3
Protect flat work surface, such as top of dryer or floor near dryer,
with a soft cloth or towel.
4
Be sure dryer is unplugged from power source!
WARNING
ELECTRICAL SHOCK HAZARD
Failure to disconnect power source before servicing
could result in personal injury or even death.
Preparing to reverse door swing
Screwdrivers with
#2 square &
straight bit
Tools needed:
A) Removing Trim Ring
1
Open door to 90 degree angle.
2
Remove and save trim plug and long,
course-thread, panhead screw.
3 Close door.
4
Rotate door trim approximately ¾” counter-
clockwise and pull ring away from door.
4
Gently place door face down on flat, covered
work surface.
3
While supporting the weight of the door
with both hands, separate the door from the
hinge.
B) Removing Door from Hinge
1
Reopen door to 90 degree angle.
2
Remove 4 long, course-thread, counter-sunk
hinge screws from door.
Removing door and hardware