Epson 2080 Service Manual - Page 48

LQ-2080 7.1 EEPROM Address Map NOTE: The data of two or more bytes are assigned in such way as lower byte to lower address, higher byte to higher address. Table 7-1. EEPROM Address Map (1/7) Address Data Data Format Q-pit Factory data setting 00H, 01H (reserved) 0000H 0000H Area 1 02H, 03H Character table selection 0: PC437 19:ISO 8859-7 1: PC850 20:MAZOWIA 2: PC860 21:Code MJK 3: PC863 22:Bulgaria 4: PC865 23:Estonia 5: PC861 24:PC774 6: BRASCII 25:ISO 8859-2 7: Abicomp 26:PC866 LAT 8: ISO Latin 1 27:PC866 UKR 9: Roman 8 28:Hebrew 7 10:PC437 Greek 29:Hebrew 8 11:PC852 30:PC862 12:PC853 31:PCAPTEC 13:PC855 32:PC708 14:PC857 33:PC720 15:PC864 34:PCAR864 16:PC866 35:PC858 17:PC869 36:ISO 8859-15 18:ISO Latin 1T 37:Italic U.S.A. 41:Italic Denmark 38:Italic France 42:Italic Sweden 39:Italic Germany I 43:Italic Italy 40:Italic U.K. 44:Italic Spain 0000H 0000H (PC437) Revision A Table 7-2. EEPROM Address Map (2/7) Address Data Data Format Q-pit Factory data setting 04H, 05H Page length for rear 1 to 22x360 (by 1/360 inch) 0000H 0000H tractor 0000H: 11 inch (default) (11 inch) (11 inch) 06H, 07H Page length for front 1 to 22x360 (by 1/360 inch) 0000H 0000H tractor 0000H: 11 inch (default) (11 inch) (11 inch) 08H, 09H Page length for CSF 1 to 22x360 (by 1/360 inch) 0000H 0000H bin 1 0000H: 22 inch (default) (22 inch) (22 inch) 0AH, 0BH Page length for CSF 1 to 22x360 (by 1/360 inch) 0000H 0000H bin 2 0000H: 22 inch (default) (22 inch) (22 inch) 0CH, 0DH TOF adjustment -60 to 360 (4.2 mm to 8.5 0000H 0000H value for rear tractor mm + 1 inch, by 1/360 inch) (8.5 mm) (8.5 mm) 0EH, 0FH TOF adjustment -60 to 360 (4.2 mm to 8.5 0000H 0000H value for front tractor mm + 1 inch, by 1/360 inch) (8.5 mm) (8.5 mm) 10H, 11H TOF adjustment -60 to 360 (4.2 mm to 8.5 0000H 0000H value for CSF bin 1 mm + 1 inch, by 1/360 inch) (8.5 mm) (8.5 mm) 12H, 13H TOF adjustment -60 to 360 (4.2 mm to 8.5 0000H 0000H value for CSF bin 2 mm + 1 inch, by 1/360 inch) (8.5 mm) (8.5 mm) 14H, 15H TOF adjustment -60 to 360 (4.2 mm to 8.5 value for rear manual mm + 1 inch, by 1/360 inch) insertion 0000H 0000H (8.5 mm) (8.5 mm) 16H, 17H TOF adjustment value for front manual insertion -60 to 360 (4.2 mm to 8.5 0000H 0000H mm + 1 inch, by 1/360 inch) (8.5 mm) (8.5 mm) 18H, 19H Bottom margin for rear tractor 1 to 22x360 (by 1/360 inch), 0000H 0000H 0000H: 11inch (default) (11 inch) (11 inch) 1AH, 1BH Bottom margin for front tractor 1CH Font selection 1 to 22x360 (by 1/360 inch), 0000H: 11inch (default) 0: Roman 1: Draft 2: Sans serif 3: Courier 4: Prestige 5: Script 6: Others (default) 0000H 0000H (11 inch) (11 inch) 00H 00H (Roman) (Roman) Appendix EEPROM Address Map 48