Epson 5700i User Manual - Page 93

nSelectln/IEEE1284active, low to terminate 1284 mode, setting the bus direction from

Get Epson 5700i - EPL B/W Laser Printer PDF manuals and user guides
UPC - 010343818620
View all Epson 5700i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

Negotiation phase: This signal is set high in order to authorize 1284 compatibility. In nibble mode, after the host sets HostBusy (nAutoFd) high, this signal is set low in order to indicate that the transmission data is ready. Reverse data transfer phase: This signal is set low in order to indicate to a nibble mode host that the transmission data is ready. Afterwards, this signal serves as nibble data bit 0 and then 4. Reverse idle phase: Indicates whether or not the data is valid. ECP mode: This signal is set low to request communications with the host. Valid in both forward and reverse directions. nSelectln/IEEE1284active Compatibility mode: Always low Negotiation phase: This signal is set high at the same time that A HostBusy is low in order to request 1284 mode. Reverse data transfer phase: This signal is set high to indicate that the bus direction is from the printer to the host. This signal is set low to terminate 1284 mode, setting the bus direction from the host to the printer. Reverse idle phase: Same as reverse data transfer phase ECP mode: Always high. This signal is set low to terminate ECP mode and return to compatibility mode. GND Twisted pair return signal CG Connected to the printer chassis. This signal and GND are connected. Technical Specifications A-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
A
Technical Specifications
A-11
Negotiation phase: This signal is set high in order to authorize
1284 compatibility. In nibble mode, after the host sets HostBusy
(nAutoFd) high, this signal is set low in order to indicate that the
transmission data is ready.
Reverse data transfer phase: This signal is set low in order to
indicate to a nibble mode host that the transmission data is ready.
Afterwards, this signal serves as nibble data bit 0 and then 4.
Reverse idle phase: Indicates whether or not the data is valid.
ECP mode: This signal is set low to request communications with
the host. Valid in both forward and reverse directions.
nSelectln/IEEE1284active
Compatibility mode: Always low
Negotiation phase: This signal is set high at the same time that
HostBusy is low in order to request 1284 mode.
Reverse data transfer phase: This signal is set high to indicate that
the bus direction is from the printer to the host. This signal is set
low to terminate 1284 mode, setting the bus direction from the
host to the printer.
Reverse idle phase: Same as reverse data transfer phase
ECP mode: Always high. This signal is set low to terminate ECP
mode and return to compatibility mode.
GND
Twisted pair return signal
CG
Connected to the printer chassis. This signal and GND are
connected.