Epson BrightLink EB-735Fi Installation Guide - Page 80

Installing the touch unit above a whiteboard

Get Epson BrightLink EB-735Fi PDF manuals and user guides View all Epson BrightLink EB-735Fi manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Installing the touch unit above a whiteboard Follow the steps below to use the optional touch unit bracket to install the touch unit above the frame of a whiteboard. Some menus may differ slightly from the illustrations, but the installation instructions are the same. Install the touch unit bracket on a flat, smooth, unwarped surface. If there is unevenness on the screen surface of more than 0.2 inch (5 mm) in any direction, your fingers may not be detected and finger touch operations may not be performed correctly. A Install infrared deflectors along any obstacles If there is an obstacle that cannot be removed, such as a whiteboard tray or thick frame, remove the tape from the back of the supplied infrared deflectors and stick them to the screen so that the laser is not reflected by the obstacle. Make sure to use as many deflectors as necessary to match the full width of the obstacle. ❏ Do not remove an infrared deflector once it has been stuck in place. ❏ Do not stick tape on or place anything on the infrared deflectors. The deflectors will not function properly if anything is placed on them. 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
80
Installing the touch unit above a whiteboard
Follow the steps below to use the optional touch unit bracket to install the touch unit above the frame of a
whiteboard. Some menus may differ slightly from the illustrations, but the installation instructions are the
same.
A
Install infrared deflectors along any obstacles
If there is an obstacle that cannot be removed, such as a whiteboard tray or thick frame, remove the
tape from the back of the supplied infrared deflectors and stick them to the screen so that the laser is
not reflected by the obstacle.
Make sure to use as many deflectors as necessary to match the full width of the obstacle.
Install the touch unit bracket on a flat, smooth, unwarped surface. If there is
unevenness on the screen surface of more than 0.2 inch (5 mm) in any direction, your
fingers may not be detected and finger touch operations may not be performed
correctly.
❏
Do not remove an infrared deflector once it has been stuck in place.
❏
Do not stick tape on or place anything on the infrared deflectors. The deflectors
will not function properly if anything is placed on them.