Epson Stylus COLOR 3000 Product Information Guide - Page 12
Using the Control Panel, TRANSPORTING THE PRINTER - service manual
View all Epson Stylus COLOR 3000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
EPSON Stylus COLOR 3000 5. You see an installation instruction screen. Follow the instructions on the screen to install the utility on your computer's hard disk drive. 6. Once the utility is installed, log onto the directory you specified for the utility. Then type EPCALIB and press Enter to start the program. Note: You can use a mouse with the utility if you have a DOS mouse driver installed. 7. You see the EPSON Print Head Alignment Utility main screen. Make sure your printer is listed on the screen and select Next. 8. Follow the instructions on the utility screens to align your print heads. Using the Control Panel 1. Load several sheets of paper, at least 8.3 inches (210 mm) wide, into the paper tray, making sure the edge guides are positioned correctly and the paper-release lever is set to the singular sheet position. 2. Turn off your printer. 3. Hold down the Pause button and turn on the printer to turn on print head alignment mode. Be sure to hold down both buttons for three seconds before releasing them. The printer loads a sheet of paper and prints an instruction sheet telling you how to select a language (the default setting is English). 4. If you want to print the instructions in another language, press the Micro Adjust U button until the Ink Out B Yellow and Ink Out B Magenta lights on your control panel indicate the language you want to use. English French German Italian Spanish Portuguese Both lights off Ink Out B Yellow on and Ink Out B Magenta off Ink Out B Yellow flashing and Ink Out B Magenta off Ink Out B Yellow off and Ink Out B Magenta on Both lights on Ink Out B Yellow flashing and Ink Out B Magenta on 5. Press the Pause button. The printer prints instructions on aligning the print heads using the control panel. 6. Follow the instructions on the sheet. When the print heads are aligned, turn off the printer to exit print head alignment mode. 7. After five seconds, turn on the printer to resume printing. Transporting the Printer Caution: If you don't follow the procedures in this section, ink will leak when you transport the printer. However, if you are moving your printer a short distance, for example, from one table to another, you don't need to remove the ink cartridges. Be sure to keep the printer level when you move it. If you want to ship your printer, you need to prepare it for transportation and repack it in the original box. Follow these steps: 1. Turn on the printer. 2. Remove all four of the ink cartridges and store them in separate plastic bags. 3. Close the ink compartment door. 4. Turn off the printer and make sure the print heads are in the home (far right) position. If they are not, turn the printer back on, wait until they stop moving and are in the home position, then turn off the printer. 5. Wait until the printer stops making noise and all the lights stop flashing, then unplug the power cord from the electrical outlet and disconnect the interface cable from the printer. 6. Remove the paper from all the feeders. 7. Remove the edge guides and banner paper cover. 8. Remove the paper tray and paper tray cover. 9. Repack the printer and attachments in the original box using the protective materials that came with it. See the Notice Sheet that was packed with the printer. Be sure to keep the printer level in an upright position as you transport it. If you reinstall the cartridges that were removed in step 2, the ink sensor will not correctly indicate the amount of ink in the cartridges. You may run out of ink before the Ink Out lights comes on. If you want the ink sensor to work properly, you need to install new ink cartridges. See page 9 for instructions. Related Documentation TM-STYCLR3000 EPSON Stylus COLOR 3000 Service Manual PL-STYCLR3000 EPSON Stylus COLOR 3000 Parts Price List 4007168 EPSON Stylus COLOR 3000 User's Guide 4007164 EPSON Stylus COLOR 3000 Quick Setup booklet 12 - EPSON Stylus COLOR 3000 5/97