Epson WorkForce Enterprise WF-C17590 Administrators Guide - Page 8

Using Web Config Network Configuration Software, About Web Config, Accessing Web Config, Parent topic

Get Epson WorkForce Enterprise WF-C17590 PDF manuals and user guides View all Epson WorkForce Enterprise WF-C17590 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Using Web Config Network Configuration Software Follow the instructions in these sections to configure your product's administrator network settings using the Web Config software. Note: Before you can configure system administration settings, you must connect the product to a network. See the product's User's Guide for instructions. About Web Config Accessing Web Config Restricting Features Available for Users Using Your Product on a Secure Network About Web Config Web Config is a browser-based application you can use to configure a product's settings. Basic and advanced setting pages are available. Note: Before you can configure system administration settings, you must connect the product to a network. See the product's User's Guide for instructions. You can lock the settings you select by setting up an administrator password for your product. See the product's User's Guide for instructions. Parent topic: Using Web Config Network Configuration Software Accessing Web Config You can access Web Config from your browser using HTTP or HTTPS. By default, you access Web Config for the first time using HTTP. If you continue to use HTTP, Web Config will not display all available menus. 1. Print a network status sheet for your product and identify the product IP address. See the product's User's Guide for instructions. 2. Start your web browser and make sure JavaScript is enabled. 3. Type the product IP address into the browser as follows, depending on the protocol you are using: • IPv4: http://product IP address 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
8
Using Web Config Network Configuration Software
Follow the instructions in these sections to configure your product's administrator network settings using
the Web Config software.
Note:
Before you can configure system administration settings, you must connect the product to a
network. See the product's
User's Guide
for instructions.
About Web Config
Accessing Web Config
Restricting Features Available for Users
Using Your Product on a Secure Network
About Web Config
Web Config is a browser-based application you can use to configure a product's settings. Basic and
advanced setting pages are available.
Note:
Before you can configure system administration settings, you must connect the product to a
network. See the product's
User's Guide
for instructions.
You can lock the settings you select by setting up an administrator password for your product. See the
product's
User's Guide
for instructions.
Parent topic:
Using Web Config Network Configuration Software
Accessing Web Config
You can access Web Config from your browser using HTTP or HTTPS.
By default, you access Web Config for the first time using HTTP. If you continue to use HTTP, Web
Config will not display all available menus.
1.
Print a network status sheet for your product and identify the product IP address. See the product's
User's Guide
for instructions.
2.
Start your web browser and make sure JavaScript is enabled.
3.
Type the product IP address into the browser as follows, depending on the protocol you are using:
• IPv4: http://
product IP address