Fisher and Paykel RS36A72J1 Installation Manual - Page 18

Connect To Water And Electrical Supply

Get Fisher and Paykel RS36A72J1 PDF manuals and user guides View all Fisher and Paykel RS36A72J1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

!0 CONNECT TO WATER AND ELECTRICAL SUPPLY IMPORTANT! ●● The water connection to your Ice & Water refrigerator must be installed by a qualified plumber or a Fisher & Paykel Authorized Service Agent. ●● The water connection instructions below are intended only for the professional installer. ●● DO NOT use water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. ●● WARNING - connect to potable water supply only. ●● DO NOT install on line pressure above 120 psi (827 kPa) or below 22 psi (150 kPa). ●● DO NOT use on hot water supply (100°F [38°C max.]). ●● AVOID contamination of pipes during installation. ●● New water fittings (hose-sets) are to be used on the appliance. Old water fittings (hose-sets) should not be reused. ●● The standard appliance does not include water fittings. Fisher & Paykel water fittings are available (part number: 841301). These parts need to be purchased separately by the customer and comply with local regulations. 3 At the front of the product, dislodge the PLV. Grasp the PLV from the clips by pulling it towards you (refer to A). A Front view The assembly of Fisher & Paykel water fittings are outlined below, other water fittings purchased separately also follow the installation steps below: 1 Ensure the refrigerator is NOT plugged into a power supply. Locate isolating faucet for water connection - cold water supply only. Tee and faucet fitting not supplied. Ensure there is enough tubing for the water connection and to pull the appliance out for service, if required. 2 Uncoil the ¼" (6 mm) water tubing and thread one end through the opening in the rear cover until it exits the front. 4 Firmly insert water tubing into the PLV. The tube should push in at least 5/8" (16 mm) before reaching the stop. Once inserted, pull gently on tubing to ensure it is locked in (refer to B). Secure the connection by attaching the locking key in between the PLV and water tubing (refer to C). Mount the PLV back into the clip. B Rear view C 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
16
!0
CONNECT TO WATER AND ELECTRICAL SUPPLY
IMPORTANT!
●
±
The water connection to your Ice & Water refrigerator must be installed by a qualified
plumber or a Fisher & Paykel Authorized Service Agent.
●
±
The water connection instructions below are intended only for the professional installer.
●
±
DO NOT use water that is microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system.
●
±
WARNING – connect to potable water supply only.
●
±
DO NOT install on line pressure above 120 psi (827 kPa) or below 22 psi (150 kPa).
●
±
DO NOT use on hot water supply (100°F [38°C max.]).
●
±
AVOID contamination of pipes during installation.
●
±
New water fittings (hose-sets) are to be used on the appliance. Old water fittings
(hose-sets) should not be reused.
●
±
The standard appliance does not include water fittings. Fisher & Paykel water fittings
are available (part number: 841301). These parts need to be purchased separately by
the customer and comply with local regulations.
The assembly of Fisher & Paykel water fittings are outlined below, other water fittings
purchased separately also follow the installation steps below:
1
Ensure the refrigerator is NOT plugged into a power supply. Locate isolating faucet
for water connection – cold water supply only. Tee and faucet fitting not supplied.
Ensure there is enough tubing for the water connection and to pull the appliance
out for service, if required.
2
Uncoil the °” (6 mm) water tubing and thread one end through the opening in the rear
cover until it exits the front.
4
Firmly insert water tubing into the PLV. The tube should push in at least ¹” (16 mm)
before reaching the stop. Once inserted, pull gently on tubing to ensure it is locked
in (refer to
B
).
Secure the connection by attaching the locking key in between the PLV and water
tubing (refer to
C
). Mount the PLV back into the clip.
Rear view
3
At the front of the product, dislodge the PLV. Grasp the PLV from the clips by pulling
it towards you (refer to
A
).
Front view
A
C
B