Frigidaire FAFS4272LW Wiring Diagram (All Languages) - Page 2

Delay Start, center bu - model

Get Frigidaire FAFS4272LW PDF manuals and user guides
UPC - 012505382208
View all Frigidaire FAFS4272LW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

2. Turn the program knob (1) click clockwise from the start position. The hot water solenoid will activate and hot water should enter through the detergent compartment. 3. Turn the program knob (2) clicks from the start position. The bleach water solenoid will activate and cold water should enter through the bleach compartment. 4. Turn the program knob (3) clicks from the start position. The bleach and the wash water solenoids will activate and cold water should enter through the softener compartment. 5. Turn the program knob (4) clicks from the start position. The prewash solenoid will activate and cold water should enter through the prewash compartment. 6. Turn the program knob (5) clicks from the start position. The door lock solenoid will deactivate and the loading door can be opened. When the door is opened, the drum light should turn on, if so equipped. 7. Turn the program knob (6) clicks from the start position. The door lock will activate and the washer will fill then tumble. Once tumbling has started, the Boost Heater will turn on. 8. Turn the program knob (7) clicks from the start position. This is a free position on models without a recirculation pump. The recirculation pump and drum light will activate if so equipped. 9. Turn the program knob (8) clicks from the start position. The drain pump will activate draining out any water in the tub. To enable high spin, press the Delay Start key. 10. Turn the program knob (9) clicks from the start position. The control will signal the last 5 error codes with E00 being no error. 11. Turn the program knob (10) clicks from the start position. Latest software version will be shown. 12. If applicable, turn the program knob (11) clicks from the start position. This is a free position. Exiting Diagnostic Mode To return the washer to normal operation: a) Unplug the power cord, wait 5-8 seconds, then reconnect the power cord OR b) Turn the program knob clockwise back to the Start Position. Press the "cancel" and center button under the display until the LEDs stop flashing. FACTORY RESET 1¼"x2" display models, wake machine, push the spin speed and soil selection keys simultaneously and hold until you hear a beep. This is no more than 10 seconds. 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
2
2.
Turn the program knob (1) click clockwise from the start position. The hot water solenoid will activate and hot water should
enter through the detergent compartment.
3.
Turn the program knob (2) clicks from the start position. The bleach water solenoid will activate and cold water should enter
through the bleach compartment.
4.
Turn the program knob (3) clicks from the start position. The bleach and the wash water solenoids will activate and cold
water should enter through the softener compartment.
5.
Turn the program knob (4) clicks from the start position. The prewash solenoid will activate and cold water should enter
through the prewash compartment.
6.
Turn the program knob (5) clicks from the start position. The door lock solenoid will deactivate and the loading door can be
opened. When the door is opened, the drum light should turn o
n, if so equipped.
7.
Turn the program knob (6) clicks from the start position. The door lock will activate and the washer will fill then tumble.
Once tumbling has started, the Boost Heater will turn on.
8.
Turn the program knob (7) clicks from the start position. This is a free position on models without a recirculation pump.
The
recirculation pump and drum light will activate if so equipped.
9.
Turn the program knob (8) clicks from the start position.
The drain pump will activate draining out any water in the tub.
To
enable high spin, press the
Delay Start
key.
10. Turn the program knob (9) clicks from the start position. The control will signal the last 5 error codes with E00 bei
ng no
error.
11. Turn the program knob (10) clicks from the start position. Latest software version will be shown.
12. If applicable, turn the program knob (11) clicks from the start position. This is a free position.
Exiting Diagnostic Mode
To return the washer to normal operation:
a)
Unplug the power cord, wait 5-8 seconds, then reconnect the power cord
OR
b)
Turn the program knob clockwise back to the
S
t
art Position. Press the “
cancel
”
and
center bu
tton under the display
until the LEDs stop flashing.
F
ACT
OR
Y
RESET
1¼”x2” display models, wake machine, push the spin speed and soil selection keys simultaneously and hold until you hear a
beep.
This is no more than 10 seconds.