Garmin GPSMAP 741xs Owner's Manual - Page 72

Capturing Screenshots, User CarD Not founD, Please Insert CarD

Get Garmin GPSMAP 741xs PDF manuals and user guides View all Garmin GPSMAP 741xs manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Appendix either been disconnected or the unit has lost communication with the sonar device for some other reason. Track Already Exists [Track Name]-you entered a saved track name that already exists in memory. Modify the track name or delete the existing track. Track Log Full-the track log is full and track recording has been turned off. To record more track points, you need to clear the track log and turn track recording on. This only appears when the track recording setting is set to "Stop When Full." Track Memory is Full, Can't Create Track-the track log memory is full. No additional track log data can be stored without deleting old data to create memory space. Track Truncated-a complete uploaded track does not fit into memory. The oldest track log points were deleted to make space for the most recent data. Transducer Disconnected, Sonar Turned Off-there is not a transducer attached, there is a bad cable or transducer, or the transducer cable was disconnected. If the transducer cable is removed while the unit is on, reconnect and cycle power. Transfer Complete-the unit has finished uploading or downloading information to the connected device. User Card Not Found, Please Insert Card-attempted to transfer user data without an SD card containing user data being present in the SD card slot. Warning: Auto-guidance route starting and ending position moved due to safe depth settings-the auto-guidance route was calculated but the starting and ending positions were moved because of safe depth settings. Water Speed Sensor Is Not Working-the speed sensor is not detected. Check the connections. Water Temperature Alarm-sonar has reported a temperature above, below, inside, or outside the specified values. Waypoint Already Exists-you entered a waypoint name that already exists in memory. Modify the waypoint name or delete the existing waypoint. Waypoint Memory Full-you have saved the maximum number of waypoints. Delete unwanted waypoints to make space for new entries. Capturing Screenshots You can capture a screenshot of any screen displayed on your unit as a bitmap (.BMP) file and then transfer it to your computer. To capture screenshots: 1. Insert an SD card into the SD card slot on the front of the unit. 2. Select Configure > System > Beeper/Display. 3. Select Screenshot Capture to turn screenshot captures On. 4. When you are on a screen you want to capture, press and hold the HOME button for at least six seconds. 5. Select OK when the Screenshot Taken window is displayed. To copy the screenshots to your computer: 1. Remove the SD card from the chartplotter and insert it into an SD card reader that is attached to a computer. 2. From Windows Explorer, open the Garmin\scrn folder on the SD card. 66 GPSMAP 400/500 Series Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Appendix
66
GPSMAP 400/500 Series Owner’s Manual
either been disconnected or the unit has lost communication with the sonar
device for some other reason.
Track AlreaDY Exists [Track Name]
—you entered a saved track name that
already exists in memory. Modify the track name or delete the existing track.
Track Log full
—the track log is full and track recording has been turned
off. To record more track points, you need to clear the track log and turn track
recording on. This only appears when the track recording setting is set to “Stop
When Full.”
Track MemorY is full, Can’t Create Track
—the track log memory is full.
No additional track log data can be stored without deleting old data to create
memory space.
Track TruncateD
—a complete uploaded track does not fit into memory. The
oldest track log points were deleted to make space for the most recent data.
TransDucer disconnecteD, Sonar TurneD OFF
—there is not a transducer
attached, there is a bad cable or transducer, or the transducer cable was
disconnected. If the transducer cable is removed while the unit is on, reconnect
and cycle power.
TransFer Complete
—the unit has finished uploading or downloading
information to the connected device.
User CarD Not founD, Please Insert CarD
—attempted to transfer user data
without an SD card containing user data being present in the SD card slot.
Warning: Auto-guiDance route starting anD enDing position moveD Due to
saFe Depth settings
—the auto-guidance route was calculated but the starting
and ending positions were moved because of safe depth settings.
Water SpeeD Sensor Is Not Working
—the speed sensor is not detected.
Check the connections.
Water Temperature Alarm
—sonar has reported a temperature above, below,
inside, or outside the specified values.
WaYpoint AlreaDY Exists
—you entered a waypoint name that already exists
in memory. Modify the waypoint name or delete the existing waypoint.
WaYpoint MemorY full
—you have saved the maximum number of
waypoints. Delete unwanted waypoints to make space for new entries.
Capturing Screenshots
You can capture a screenshot of any screen displayed on your unit as a bitmap
(.BMP) file and then transfer it to your computer.
To capture screenshots:
1.
Insert an SD card into the SD card slot on the front of the unit.
2. Select
Configure
>
SYstem
>
beeper/displaY
.
3. Select
Screenshot Capture
to turn screenshot captures
On
.
4.
When you are on a screen you want to capture, press and hold the
HOME
button for at least six seconds.
5. Select
OK
when the Screenshot Taken window is displayed.
To copy the screenshots to your computer:
1.
Remove the SD card from the chartplotter and insert it into an SD card
reader that is attached to a computer.
2.
From Windows Explorer, open the Garmin\scrn folder on the SD card.