GE PDW8600NCC Installation Instructions - Page 11

Step 14 Connect Water Supply, Step 15 Connect Drain Line, Drain Line Installation

Get GE PDW8600NCC - on 24 Inch Full Console Dishwasher PDF manuals and user guides View all GE PDW8600NCC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Installation Instructions STEP 14 CONNECT WATER SUPPLY Connect water supply line to the 90° elbow. • Slide compression nut, then ferrule over end of water line. • Insert water line into 90° elbow. • Slide ferrule against elbow and secure with compression nut. IMPORTANT - Check to be sure that door spring does not rub or contact the fill hose or water supply line. Test by opening and closing the door. Reroute the lines if a rubbing noise or interference occurs. Figure EE Compression Nut Ferrule 90° Elbow Hot Water Supply Line 90° Elbow Door Spring STEP 15 CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES AND ORDINANCES. The molded end of the drain hose will fit 5/8" through 1" diameter inlet ports on the air gap, waste tee or disposer. • Determine size of inlet port • Cut drain hose connector on the marked line, if required, to fit the inlet port. Method 1 - Air gap with waste tee or disposer Insert the drain hose to air ga0p5aAs-s1h1ow8n3.CC Cutting Line IMPORTANT: Do not cut corrugated portion of hose 1" 5/8" Figure FF Waste Tee Installation Disposer Installation Figure HH Method 2 - Drain Hose Routing Route the drain hose of the dishwasher to a minimum height of 32" from theFaflsotoernwditrhaitnhehosuseppaltieldeahsatnagter as shoFwanst.en drain hose at least at 32" height with hanger supplied 32" height with hanger supplied • If a longer drain hose is required, add up to 42" of length for a total of 10' to the factory installed hose. Use 5/8" or 7/8" inside diameter hose and a coupler to connect9th2e t3w-o10A hose ends. Secure the connection with hose clamps. Figure GG • Secure the drain hose to the air gap, waste tee or disposer with clamps. Note: TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 10' FOR PROPER DRAIN OPERATION. DRAIN LINE INSTALLATION • Connect drain line to air gap, waste tee or disposer using either previously determined method. 32" 18" Min. Min. 32" 18" Min. Min. Waste Tee Installation Disposer Installation Figure JJ 05A-1183FF 05A-1183GG IMPORTANT - Either one of the above methods must be used or dishwasher will not operate properly. IMPORTANT - When connecting drain line to disposer, check to be sure that drain plug has been removed. DISHWASHER WILL NOT DRAIN IF PLUG IS LEFT IN PLACE. ���� Tip: Avoid unnecessary service call charges. Always be sure disposer drain plug has been removed before attaching dishwasher drain hose to the disposer. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
Installation Instructions
10
STEP 14 CONNECT WATER SUPPLY
Connect water supply line to the 90° elbow.
• Slide compression nut, then ferrule over end of water line.
• Insert water line into 90° elbow.
• Slide ferrule against elbow and secure with compression nut.
IMPORTANT
– Check to be sure that door spring
does not rub or contact the fill hose or water supply line. Test
by opening and closing the door. Reroute the lines if a rubbing
noise or interference occurs.
Figure EE
Figure FF
STEP 15 CONNECT DRAIN LINE
FOLLOW ALL LOCAL CODES AND ORDINANCES.
The molded end of the drain hose will fit 5/8" through 1"
diameter inlet ports on the air gap, waste tee or disposer.
• Determine size of inlet port
• Cut drain hose connector on the marked line, if required, to fit
the inlet port.
• If a longer drain hose is required, add up to 42" of length for
a total of 10' to the factory installed hose. Use 5/8" or 7/8"
inside diameter hose and a coupler to
connect the two
hose ends.
Secure the
connection with
hose clamps.
Figure GG
• Secure the drain hose to the air gap, waste tee or disposer
with clamps.
Note:
TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 10' FOR
PROPER DRAIN OPERATION.
DRAIN LINE INSTALLATION
• Connect drain line to air gap, waste tee or disposer using
either previously determined method.
Waste Tee Installation
Figure HH
Disposer Installation
Waste Tee Installation
Figure JJ
Disposer Installation
Method 2 – Drain Hose Routing
Route the drain hose of the dishwasher to a minimum height of 32" from
the floor with the supplied hanger as shown.
IMPORTANT
– When connecting
drain line to disposer, check to be sure
that drain plug has been removed.
DISHWASHER WILL NOT DRAIN IF
PLUG IS LEFT IN PLACE.
Tip:
Avoid unnecessary service call charges. Always be sure
disposer drain plug has been removed before attaching
dishwasher drain hose to the disposer.
�±²³´±
µ³¶¶±·
¸¹º»
90
°
Elbow
90
°
Elbow
Ferrule
Door Spring
Hot Water
Supply Line
Compression Nut
µ³Â±Ç¼¹½²¶
¼³º¶¹±·
µ³Â±Ç¼¹½²¶
Cutting Line
1"
5/8"
IMPORTANT:
Do not cut corrugated
portion of hose
18"
Min.
32"
Min.
IMPORTANT
– Either one of the above methods
must be used or dishwasher will not operate properly.
Method 1 – Air gap with waste tee or disposer
Insert the drain hose to air gap as shown.
32"
Min.
18"
Min.