Gigabyte GA-78LMT-USB3 Manual - Page 17

SATA2 0/1/2/3/4/5 SATA 3Gb/s Connectors, Controlled by AMD SB710 South Bridge, IDE IDE Connector - raid

Get Gigabyte GA-78LMT-USB3 PDF manuals and user guides View all Gigabyte GA-78LMT-USB3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

6) IDE (IDE Connector) The IDE connector supports up to two IDE devices such as hard drives and optical drives. Before attaching the IDE cable, locate the foolproof groove on the connector. If you wish to connect two IDE devices, remember to set the jumpers and the cabling according to the role of the IDE devices (for example, master or slave). (For information about configuring master/slave settings for the IDE devices, read the instructions from the device manufacturers.) 1 2 39 40 DEBUG PORT DEBUG PORT 7) SATA2 0/1/2/3/4/5 (SATA 3Gb/s Connectors, Controlled by ADMEBDUGSB710DSEBoUuGth Bridge) The SATA connectors conform to SATA 3Gb/s standard and are compaPtiOblReTwith SATPAOR1T.5Gb/s standard. Each SATA connector supports a single SATA device. The AMD SB710 coDnEBtrUoGller suppDoErtBsURGAID 0, RAID 1, RAID 10, and JBOD. Refer to Chapter 4, "Configuring SATA Hard Drive(PsO),R"Tfor instrucPtOioRnTs on configuring a RAID array. 1 SATA2 5 4 SATA2 2 0 3 1 7 Pin No. 1 2 3 4 5 6 7 Definition GND TXP TXN GND RXN RXP GND 1 7 1 7 •• A RAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard drives are to be used, the total number of hard drives must be an even number. •• A RAID 10 configuration requires four hard drives. - 17 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
- 17 -
Pin No.
Definition
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
7
7
1
1
7)
SATA2 0/1/2/3/4/5 (SATA 3Gb/s Connectors, Controlled by AMD SB710 South Bridge)
The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard.
Each SATA connector supports a single SATA device. The AMD SB710 controller supports RAID 0, RAID 1,
RAID 10, and JBOD. Refer to Chapter 4, "Configuring SATA Hard Drive(s)," for instructions on configuring
a RAID array.
6)
IDE (IDE Connector)
The IDE connector supports up to two IDE devices such as hard drives and optical drives. Before attaching
the IDE cable, locate the foolproof groove on the connector. If you wish to connect two IDE devices, remember
to set the jumpers and the cabling according to the role of the IDE devices (for example, master or slave).
(For information about configuring master/slave settings for the IDE devices, read the instructions from the
device manufacturers.)
SATA2
5
4
SATA2
2
3
0
1
7
1
•
A RAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard drives
are to be used, the total number of hard drives must be an even number.
•
A RAID 10 configuration requires four hard drives.
1
39
2
40