Gigabyte GA-E7AUM-DS2H Manual - Page 82

Making a SATA RAID/AHCI Driver Diskette

Get Gigabyte GA-E7AUM-DS2H PDF manuals and user guides View all Gigabyte GA-E7AUM-DS2H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

5-1-2 Making a SATA RAID/AHCI Driver Diskette (Required for AHCI and RAID Mode) To successfully install operating system onto SATA hard drive(s) that is/are configured to RAID/AHCI mode, you need to install the SATA controller driver during the OS installation. Without the driver, the hard drive may not be recognized during the Windows setup process. First of all, copy the driver for the SATA controller from the motherboard driver disk to a floppy disk. For installing Windows Vista, you first have to copy the SATA controller driver from the motherboard driver disk to your USB flash drive and then extract it (see instructions on the next page). See the instructions below about how to copy the driver in MS-DOS mode . (Note) Prepare a startup disk that has CD-ROM support and a blank formatted floppy disk. Step 1: Insert the prepared startup disk and motherboard driver disk in your system. Boot from the startup disk. Once at the A:\> prompt, change to your optical drive (example: D:\>). At the D:\> prompt, type the following two commands. Press after each command (Figure 1): cd bootdrv menu Step 2: When the controller menu (Figure 2) appears, remove the startup disk and insert the blank formatted disk. Select the controller driver by pressing the corresponding letter from the menu. For example, in the menu in Figure 2, • In RAID mode, select C) NVIDIA MCP7A Series RAID Driver(XP) for Windows XP 32-bit operating system or E) NVIDIA MCP7A Series RAID Driver(XP64Bit) for Windows XP 64-bit. • In AHCI mode, select B) NVIDIA MCP7A Series AHCI Driver(XP) for Windows XP 32-bit operating system or D) NVIDIA MCP7A Series AHCI Driver(XP64Bit) for Windows XP 64-bit. Your system will then automatically zip and transfer this driver file to the floppy disk. Press to exit when finished. Figure 1 Figure 2 (Note) For users without a startup disk: Use an alternative system and insert the motherboard driver disk. From your optical drive folder, double click the MENU.exe file in the BootDrv folder (Figure 3). A command prompt window will open similar to that in Figure 2. GA-E7AUM-DS2H Motherboard Figure 3 - 82 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
GA-E7AUM-DS2H Motherboard
- 82 -
5-1-2
Making a SATA RAID/AHCI Driver Diskette
(Required for AHCI and RAID Mode)
To successfully install operating system onto SATA hard drive(s) that is/are configured to RAID/AHCI
mode, you need to install the SATA controller driver during the OS installation. Without the driver, the
hard drive may not be recognized during the Windows setup process. First of all, copy the driver for
the SATA controller from the motherboard driver disk to a floppy disk. For installing Windows Vista, you
first have to copy the SATA controller driver from the motherboard driver disk to your USB flash drive
and then extract it (see instructions on the next page). See the instructions below about how to copy the
driver in MS-DOS mode
(Note)
. Prepare a startup disk that has CD-ROM support and a blank formatted
floppy disk.
Step 1: Insert the prepared startup disk and motherboard driver disk in your system. Boot from the
startup disk. Once at the A:\> prompt, change to your optical drive (example: D:\>). At the D:\> prompt,
type the following two commands. Press <Enter> after each command (Figure 1):
cd bootdrv
menu
Step 2: When the controller menu (Figure 2) appears, remove the startup disk and insert the blank
formatted disk. Select the controller driver by pressing the corresponding letter from the menu. For
example, in the menu in Figure 2,
•
In RAID mode, select
C) NVIDIA MCP7A Series RAID Driver(XP)
for Windows XP 32-bit operating
system
or
E) NVIDIA MCP7A Series RAID Driver(XP64Bit)
for Windows XP 64-bit.
•
In AHCI mode, select
B) NVIDIA MCP7A Series AHCI Driver(XP)
for Windows XP 32-bit operating
system
or
D) NVIDIA MCP7A Series AHCI Driver(XP64Bit)
for Windows XP 64-bit.
Your system will then automatically zip and transfer this driver file to the floppy disk. Press <0> to exit
when finished.
Figure 1
Figure 2
Figure 3
(Note)
For users without a startup disk:
Use an alternative system and insert the motherboard driver disk. From your optical drive
folder, double click the
MENU.exe
file in the
BootDrv
folder (Figure 3). A command prompt
window will open similar to that in Figure 2.