Gigabyte GA-K8VM800M User Manual - Page 80

Delete Disk Array, Select Boot Array

Get Gigabyte GA-K8VM800M PDF manuals and user guides View all Gigabyte GA-K8VM800M manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

English Delete Disk Array A RAID can be deleted after it has been created. To delete a RAID, use the following steps: 1. Select Delete Array in the main menu and press . The channel column will be activated. 2. Select the member of an array that is to be deleted and press . A warning message will show up, press Y to delete or press N to cancel. VIA Technologies,Inc. VIA VT8237 Serial ATA BIOS Setting Utility V1.20 X Create Array X Delete Array X Create/Delete Spare X Select Boot Array X Serial Number View The selected array will be destoried. Are you sure? Continue? Press Y/N Delete a RAID array contain the hard disks attached to VIA IDE controller F1 : View Array/disk Status K, L : Move to next item Enter : Confirm the selection ESC : Exit Channel [*]Serial_Ch0 Master [*]Serial_Ch1 Master Driver Name ST380013AS ST9120023AS Array Name Mode SATA SATA Size(GB) 74.53 111.79 Status Stripe0 Stripe1 Deleting a disk array will destroy all the data on the disk array except RAID 1 arrays. When a RAID is deleted, the data on these two hard disk drives will be reserved and become two normal disk drives. Select Boot Array User can select a disk array as boot device if user wants to boot operating system from an array. Boot disk array cannot be selected if the operating system does not boot from the disk array. Highlight the Select Boot Array item; press and the channel column will be activated. Then highlight the target disk array and press . If user selects a disk array that has a boot mark and press , its boot setting will be canceled. VIA Technologies,Inc. VIA VT8237 Serial ATA BIOS Setting Utility V1.20 X Create Array X Delete Array X Create/Delete Spare X Select Boot Array X Serial Number View Set/Clear bootable array F1 K, L Enter ESC : View Array/disk Status : Move to next item : Confirm the selection : Exit Channel [*]Serial_Ch0 Master [*]Serial_Ch1 Master Driver Name ST380013AS ST9120023AS Array Name Mode SATA SATA Size(GB) 74.53 111.79 Status Stripe0 Stripe1 GA-K8VM800M Motherboard - 80 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
- 80 -
GA-K8VM800M Motherboard
English
Delete Disk Array
A RAID can be deleted after it has been created.
To delete a RAID, use the following steps:
1. Select
Delete Array
in the main menu and press <Enter>.
The channel column will be activated.
2. Select the member of an array that is to be deleted and press <Enter>.
A warning message will show
up, press
Y
to delete or press
N
to cancel.
VIA Technologies,Inc. VIA VT8237 Serial ATA BIOS Setting Utility V1.20
Delete a RAID array contain the hard disks
attached to VIA IDE controller
F1
: View Array/disk Status
,
: Move to next item
Enter
: Confirm the selection
ESC
: Exit
Create Array
Delete Array
Create/Delete Spare
Select Boot Array
Serial Number View
The selected array will be destoried.
Are you sure? Continue? Press Y/N
Channel
Driver Name
Array Name
Mode
Size(GB)
Status
[*]Serial_Ch0 Master
ST380013AS
SATA
74.53
Stripe0
[*]Serial_Ch1 Master
ST9120023AS
SATA
111.79
Stripe1
Deleting a disk array will destroy all the data on the disk array except RAID 1 arrays. When a RAID is
deleted, the data on these two hard disk drives will be reserved and become two normal disk drives.
Select Boot Array
User can select a disk array
as boot device if
user wants to
boot
operating
system
from
an
array.
Boot
disk
array
cannot
be selected if the operating system does not boot from the disk array. Highlight
the
Select Boot Array
item; press <Enter> and the channel column will be activated. Then highlight the
target disk array and press <Enter>. If user selects a disk array that has a boot mark and press <Enter>,
its boot setting will be canceled.
VIA Technologies,Inc. VIA VT8237 Serial ATA BIOS Setting Utility V1.20
Set/Clear bootable array
F1
: View Array/disk Status
,
: Move to next item
Enter
: Confirm the selection
ESC
: Exit
Create Array
Delete Array
Create/Delete Spare
Select Boot Array
Serial Number View
Channel
Driver Name
Array Name
Mode
Size(GB)
Status
[*]Serial_Ch0 Master
ST380013AS
SATA
74.53
Stripe0
[*]Serial_Ch1 Master
ST9120023AS
SATA
111.79
Stripe1