Gigabyte GA-Z77-D3H User Manual - Page 24

SATA2 2/3/4/5 SATA 3Gb/s Connectors, Controlled by Intel Z77/H77 Chipset - intel z77 chipset

Get Gigabyte GA-Z77-D3H PDF manuals and user guides View all Gigabyte GA-Z77-D3H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

6) SATA3 0/1 (SATA 6Gb/s Connectors, Controlled by Intel Z77/H77 Chipset) The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. (Please use the included SATA 6Gb/s cable). The SATA3 0/1 connectors support RAID 0 and RAID 1. RAID 5 and RAID 10 can be im- plemented on the two connectors with the "SATA2 2/3/4/5" and mSATA connectors . (Note) Refer to Chapter 5, "Configuring SATA Hard Drive(s)," for instructions on configuring a RAID array. G.QBOFM Pin No. Definition 1 GND SATA3 2 TXP 7 11 3 TXN 7 10 4 GND 5 RXN 6 RXP 7 GND DEBUG PORT Please coDnEnBeUctGthe L-shaped end of the SATA cabPleOtRoTyour SATA hard drive. 7) SATA2 2/3/4/5 (SATA 3Gb/s Connectors, Controlled by Intel Z77/H77 Chipset) The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. (Please use the included SATA 3Gb/s cable). The Intel Z77/H77 Chipset supports RAID 0, RAID 1, RAID 5, and RAID 10. Refer to Chapter 5, "Configuring SATA Hard Drive(s)," for instructions on configuring a RAID array. SATA2 7 1 1 7 2 3 4 5 7 1 1 7 Pin No. 1 2 3 4 5 6 7 Definition GND TXP TXN GND RXN RXP GND (Note) DEBUG PORT DEBUG PORT Please connect the L-shaped end of the SATA cable to your SATA hard drive. • A RAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard drives are to be used, the total number of hard drives must be an even number. • A RAID 5 configuration requires at least three hard drives. (The total number of hard drives does not have to be an even number.) • A RAID 10 configuration requires four hard drives. When a RAID set is built across the SATA 6Gb/s and SATA 3Gb/s channels, the system perfor- mance of the RAID set may vary depending on the devices being connected. Hardware Installation - 24 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
- 24 -
Hardware Installation
7)
SATA2 2/3/4/5 (SATA 3Gb/s Connectors, Controlled by Intel Z77/H77 Chipset)
The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard.
Each SATA connector supports a single SATA device.
(Please use the included SATA 3Gb/s cable)
. The
Intel Z77/H77 Chipset supports RAID 0, RAID 1, RAID 5, and RAID 10. Refer to Chapter 5, "Con
fi
guring
SATA Hard Drive(s)," for instructions on con
fi
guring a RAID array.
6)
SATA3 0/1 (SATA 6Gb/s Connectors, Controlled by Intel Z77/H77 Chipset)
The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA
1.5Gb/s standard. Each SATA connector supports a single SATA device. (Please use the included SATA
6Gb/s cable).
The SATA3 0/1 connectors support RAID 0 and RAID 1. RAID 5 and RAID 10 can be im-
plemented on the two connectors with the "SATA2 2/3/4/5" and mSATA connectors
(Note)
. Refer to Chapter
5, "Con
fi
guring SATA Hard Drive(s)," for instructions on con
fi
guring a RAID array.
A RAID 0 or RAID 1 con
fi
guration requires at least two hard drives. If more than two hard
•
drives are to be used, the total number of hard drives must be an even number.
A RAID 5 con
fi
guration requires at least three hard drives. (The total number of hard drives
•
does not have to be an even number.)
A RAID 10 con
fi
guration requires four hard drives.
•
(Note)
When a RAID set is built across the SATA 6Gb/s and SATA 3Gb/s channels, the system perfor-
mance of the RAID set may vary depending on the devices being connected.
1
1
SATA3
7
7
Pin No.
De
fi
nition
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
Pin No.
De
fi
nition
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
Please connect the L-shaped end of the
SATA cable to your SATA hard drive.
1
0
SATA2
7
7
1
1
7
1
7
1
2
3
4
5
Please connect the L-shaped end of the
SATA cable to your SATA hard drive.