Harman Kardon AVR 325 Owners Manual - Page 39
Transport Control Punch-Through, Reassigning Device Control Selectors, Resetting the Remote Memory
View all Harman Kardon AVR 325 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 39 highlights
PROGRAMMING THE REMOTE the device selected by the AVR 325 or the remote. To program the remote for Channel Control PunchThrough, follow these steps: 1. Press the Input Selector Button ef for the device you wish to have the channel control associated with and the Mute Button 43 at the same time until the red light appears under the Input Selector ef and the Program/SPL Indicator c flashes amber. 2. Press the Volume Down Button 40 . The Program/SPL Indicator c will stop flashing and stay amber. 3. Press and release the Input Selector Button e for the device that will be used to change the channels. The Program/SPL Indicator c will blink green three times and then go out to confirm the data entry. Example: To control the channels using your cable box or satellite receiver while the remote is set to control the VCR, first press the VID 1/VCR Input Selector Button e and the Mute Button 43 at the same time. Next, release them and press the Volume Down Button 40 , followed by the VID 2/ TV Input Selector Button e. NOTE: To remove the Channel Control Punch-Through and return the remote to its original configuration, repeat the steps shown in the example above. However, press the same Input Selector in Steps 1 and 3. Transport Control Punch-Through The AVR 325's remote may be programmed to operate so that the Transport Control Functions ` (Play, Stop, Fast Forward, Rewind, Pause and Record) for a VCR, DVD or CD will operate in conjunction with one of the other devices controlled by the remote. For example, while using and controlling the TV, you may wish to start or stop your VCR or DVD without having to change the device selected by the AVR 325 or the remote. To program the remote for Transport Control PunchThrough, follow these steps: 1. Press the Input Selector ef for the device you wish to have the channel control associated with and the Mute Button 43 at the same time until the red light appears under the Input Selector e and the Program/SPL Indicator c flashes amber. 2. Press the Play Button `. The Program/SPL Indicator c will stop flashing and stay amber. 3. Press and release the Input Selector Button e for the device that will be used to change the channels. The Program/SPL Indicator c will blink green three times and then go out to confirm the data entry. Example: To control the transport of a DVD player while the remote is set to control the TV, first press the VID 2/TV Input Selector Button e and the Mute Button 43 at the same time. Next, release them and press the Play Button `, followed by the DVD Input Selector Button e. NOTES: • To remove the Channel Control Punch-Through and return the remote to its original configuration, repeat the steps in the example above. However, press the same Input Selector in Steps 1 and 3. • Before programming the remote for Volume, Channel or Transport Punch-Through, make certain that any programming needed for the specific TV, CD, DVD, cable or satellite receivers has been completed. Reassigning Device Control Selectors Although each Input Selector e is normally assigned to the category of product shown on the remote, it is possible to reassign one of these buttons to operate a second device of another type. For example, if you have two VCRs but no satellite receiver, you may program the "SAT" button to operate a second VCR. Before following the normal programming steps for either Three-Digit entry or Auto Search code entry, you must first reassign the button with the following steps: 1. Press the Input Selector e you wish to reassign and the Mute Button 43 at the same time until the red light appears under the Input Selector e and the Program/ SPL Indicator c flashes amber. 2. Press the Input Selector e for the device you wish to program into the reassigned button. 3. Enter the three-digit code for the specific model you wish the reassigned button to operate. 4. Press the same Input Selector e pressed in Step 1 once again to store the selection. The red LED under the reassigned Input Selector will flash three times and then go out. Example: To use the CBL/SAT button to operate a second VCR, first press the CBL/SAT Input Selector e and the Mute Button 43 at the same time until the red light glows under the CBL/SAT Button e. Press the VCR Button e, followed by the three-digit code for the specific model you wish to control. Finally, press the CBL/SAT Button e again. Resetting the Remote Memory As you add components to your home theater system, occasionally you may wish to totally reprogram the remote control without the confusion of any commands, macros or "Punch-Through" programming that you may have done. To do this, it is possible to reset the remote to the original factory defaults and command codes by following these steps. However, once the remote is reset, all commands or codes that you have entered will be erased and will need to be reentered: 1. Press any of the Input Selector Buttons e and the "O" Button r at the same time until the Program/SPL Indicator c begins to flash amber. 2. Press the "3" Button r three times. 3. The red LED under the Input Selector e will go out and the Program/SPL Indicator c will stop flashing and turn green. 4. The Program/SPL Indicator c will remain green until the remote is reset. Note that this may take a while, depending on how many commands are in the memory that need to be erased. 5. When the Program/SPL Indicator c goes out, the remote has been reset to the factory settings. PROGRAMMING THE REMOTE 39