HealthRider H400 Treadmill English Manual - Page 26

Unplug The Power Cord

Get HealthRider H400 Treadmill PDF manuals and user guides View all HealthRider H400 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

With the help of another person, carefully raise the Uprights (96) as shown. Carefully pivot the Hood (64) 96 off. 64 Locate the Reed Switch (47) and the Magnet (35) on the left side of the Pulley (36). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the 3 mm 16 36 Reed Switch is about 3 mm (1/8 in.). If necessary, 47 35 loosen the Screw (16), move the Reed Switch slightly, and then retighten the Screw. Next, reattach the Hood, making sure that the Screws are in the same holes from which they were removed (see step A). Top View Then, run on the treadmill for a few minutes to check for a correct speed reading. PROBLEM: The walking belt slows when walked on SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 1mm2 (14-gauge) cord that is no longer than 1.5 m (5 ft.). b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may be permanently damaged. Remove the key and UNPLUG THE POWER CORD. Using the included hex key, turn both rear roller bolts counterclockwise 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 7 to 10 cm (3 to 4 in.) off the walking platform. Be careful to keep the walking belt centred. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened. b 7-10 cm Rear Roller Bolts c. If the walking belt still slows when walked on, see the front cover of this manual. PROBLEM: The walking belt is off-centre or slips when walked on SOLUTION: a. If the walking belt is off-centre, first remove the key and UNPLUG THE POWER CORD. If the walking belt has a shifted to the left, use the hex key to turn the left rear roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centred. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
26
With the help of another person, carefully raise the
Uprights (96) as shown. Carefully pivot the Hood (64)
off.
Locate the Reed Switch (47) and the Magnet (35) on
the left side of the Pulley (36). Turn the Pulley until
the Magnet is aligned with the Reed Switch.
Make
sure that the gap between the Magnet and the
Reed Switch is about 3 mm (1/8 in.).
If necessary,
loosen the Screw (16), move the Reed Switch slightly,
and then retighten the Screw. Next, reattach the
Hood, making sure that the Screws are in the same
holes from which they were removed (see step A).
Then, run on the treadmill for a few minutes to check
for a correct speed reading.
PROBLEM:
The walking belt slows when walked on
SOLUTION:
a. If an extension cord is needed, use only a 3-conductor, 1mm
2
(14-gauge) cord that is no longer
than 1.5 m (5 ft.).
b. If the walking belt is overtightened, treadmill performance
may decrease and the walking belt may be permanently
damaged. Remove the key and
UNPLUG THE POWER
CORD
. Using the included hex key, turn both rear roller
bolts counterclockwise 1/4 of a turn. When the walking
belt is properly tightened, you should be able to lift each
edge of the walking belt 7 to 10 cm (3 to 4 in.) off the
walking platform. Be careful to keep the walking belt cen-
tred. Then, plug in the power cord, insert the key, and run
the treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
c.
If the walking belt still slows when walked on, see the
front cover of this manual.
PROBLEM:
The walking belt is off-centre or slips when walked on
SOLUTION:
a. If the walking belt is off-centre, first remove the key and
UNPLUG THE POWER CORD
.
If the walking belt has
shifted to the left,
use the hex key to turn the left rear
roller bolt clockwise 1/2 of a turn;
if the walking belt has
shifted to the right,
turn the bolt counterclockwise 1/2 of
a turn. Be careful not to overtighten the walking belt.
Then, plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking belt
is centred.
Rear Roller Bolts
7–10 cm
b
35
Top
View
36
16
47
3 mm
64
96
a