HealthRider H400 Treadmill English Manual - Page 8

Pulse Bar with the four Pulse Bar Screws.

Get HealthRider H400 Treadmill PDF manuals and user guides View all HealthRider H400 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

5. See the inset drawing. Make sure that there are two Unuts (112) in the upper end of each Upright (96). Note: Extra U-nuts may be included. Identify the right and left Handrails (108) (there is an identification sticker on each Handrail). Hold the right Handrail near the right Upright (96), and insert the Wire Harness (118) into the large hole in the right Handrail and out of the upper end as shown. Next, hold the right Handrail (108) against the right Upright (96). Tighten a 5/16" x 3 1/2" Bolt (121), with a 5/16" Washer (130), three to four turns into the right Upright and the lower end of the right Handrail. Then, tighten two 5/16" x 1" Bolts (113) into the upper end of the right Handrail and the right Upright. Be careful not to drop the Bolts into the Handrail. If necessary, raise or lower the Handrail to thread the 5/16" x 1" Bolts into the Upright. Firmly tighten all three Bolts. Attach the left Handrail (108) to the left Upright (96) as described above. Note: There is not a wire harness in the left Upright. 6. See the inset drawing. Turn the Console (101) upsidedown on a soft surface. Remove the packing bands and the Console Back (104). If there are two Pulse Bar Screws (76) in each end of the Console Frame (80), remove them. Hold the ends of the Pulse Bar (77) against the Console Frame and attach the Pulse Bar with the four Pulse Bar Screws. Firmly tighten the Pulse Bar Screws. Be careful not to damage any wires. Locate the pulse wire extending from the Pulse Bar (77). Insert the pulse wire under the Console Frame (80) and plug the pulse wire into the indicated connector. The pulse wire should slide easily into the connector and snap into place; if it does not, turn the pulse wire and then plug it in. Attach the indicated ground wires to the Console Frame (80) with a 1/2" Ground Screw (52). 5 119 113 Left 112 118 113 108 96 130 108 121 Right 96 130 121 6 76 52 77 101 Ground Wires Connector 80 Pulse Wire 104 101 7. Attach the Console Back (104) to the console assembly 7 with five 3/4" Screws (33). Be careful not to damage any wires. Console Assembly 33 33 104 33 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
8
7.
Attach the Console Back (104) to the console assembly
with five 3/4” Screws (33).
Be careful not to damage
any wires.
104
33
Console Assembly
33
33
7
5.
See the inset drawing. Make sure that there are two U-
nuts (112) in the upper end of each Upright (96). Note:
Extra U-nuts may be included.
Identify the right and left Handrails (108) (there is an
identification sticker on each Handrail). Hold the right
Handrail near the right Upright (96), and insert the Wire
Harness (118) into the large hole in the right Handrail
and out of the upper end as shown.
Next, hold the right Handrail (108) against the right
Upright (96). Tighten a 5/16” x 3 1/2” Bolt (121), with a
5/16” Washer (130), three to four turns into the right
Upright and the lower end of the right Handrail. Then,
tighten two 5/16” x 1” Bolts (113) into the upper end of
the right Handrail and the right Upright.
Be careful not
to drop the Bolts into the Handrail.
If necessary, raise
or lower the Handrail to thread the 5/16” x 1” Bolts into
the Upright.
Firmly tighten all three Bolts.
Attach the left Handrail (108) to the left Upright (96) as
described above. Note: There is not a wire harness in the
left Upright.
6.
See the inset drawing. Turn the Console (101) upside-
down on a soft surface. Remove the packing bands and
the Console Back (104).
If there are two Pulse Bar Screws (76) in each end of the
Console Frame (80), remove them. Hold the ends of the
Pulse Bar (77) against the Console Frame and attach the
Pulse Bar with the four Pulse Bar Screws.
Firmly tighten
the Pulse Bar Screws. Be careful not to damage any
wires.
Locate the pulse wire extending from the Pulse Bar (77).
Insert the pulse wire under the Console Frame (80) and
plug the pulse wire into the indicated connector.
The
pulse wire should slide easily into the connector and
snap into place;
if it does not, turn the pulse wire and
then plug it in.
Attach the indicated ground wires to the Console Frame
(80) with a 1/2” Ground Screw (52).
5
96
118
96
108
108
113
113
121
Right
Left
121
119
112
130
130
76
52
77
101
80
6
104
101
Pulse
Wire
Connector
Ground
Wires