HP 1606 Fabric OS FCIP Administrators Guide v6.4.0 (53-1001766-01, November 20 - Page 42

Setting the GbE port operating mode (FX8-24 blade only)

Get HP 1606 PDF manuals and user guides View all HP 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

2 Configuration steps Setting the GbE port operating mode (FX8-24 blade only) The GbE ports on an FX8-24 blade can operate in one of three ways: • GbE ports 0 through 9 may be enabled as GbE ports, with the XGE ports disabled (the 10GbE license is not required). • 10GbE ports XGE0 and XGE1 may be enabled, with GbE ports 0 through 9 disabled The 10GbE license is required and must be assigned to the slot in which the FX8-24 blade resides. • GbE ports 0 through 9 and 10GbE port XGE0 may be enabled, with XGE1 disabled. The 10GbE license is required and must be assigned to the slot in which the FX8-24 blade resides. You must configure the desired GbE port mode of operation for the FX8-24 blade using the bladeCfgGeMode - -set command. The command options are as follows. 1g|10g|dual Where: 1g enables the GbE ports 0 through 9 (XGE0 and XGE1 are disabled). 10g enables ports XGE0 and XGE1 (ge0-ge9 ports are disabled). dual Enables the GbE ports 0 through 9 and XGE0 (XGE1 is disabled). Specifies the slot number for the FX8-24 blade The following example enables GbE ports 0 through 9 on an FX8-24 blade in slot 8. Ports XGE0 and XGE1 are disabled. switch:admin> bladecfggemode --set 1g -slot 8 You can use the bladecfggemode --show command to display the GbE port mode for the FX8-24 blade in slot 8, as shown in the following example. switch:admin> bladecfggemode --show -slot 8 bladeCfgGeMode: Blade in slot 8is configured in 1GigE Mode 1GigE mode: ge0-9 ports are enabled (xge0 and xge1 are disabled) switch:admin> 28 Fabric OS FCIP Administrator's Guide 53-1001766-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
28
Fabric OS FCIP Administrator’s Guide
53-1001766-01
Configuration steps
2
Setting the GbE port operating mode (FX8-24 blade only)
The GbE ports on an FX8-24 blade can operate in one of three ways:
•
GbE ports 0 through 9 may be enabled as GbE ports, with the XGE ports disabled (the 10GbE
license is not required).
•
10GbE ports XGE0 and XGE1 may be enabled, with GbE ports 0 through 9 disabled The 10GbE
license is required
and must be assigned to the slot in which the FX8-24 blade resides.
•
GbE ports 0 through 9 and 10GbE port XGE0 may be enabled, with XGE1 disabled. The 10GbE
license is required
and must be assigned to the slot in which the FX8-24 blade resides
.
You must configure the desired GbE port mode of operation for the FX8-24 blade using the
bladeCfgGeMode - -set
command. The command options are as follows.
1g
|
10g
|
dual
Where:
1g
enables the GbE ports 0 through 9 (XGE0 and XGE1 are disabled).
10g
enables ports XGE0 and XGE1 (ge0-ge9 ports are disabled).
dual
Enables the GbE ports 0 through 9 and XGE0 (XGE1 is disabled).
<slot_number>
Specifies the slot number for the FX8-24 blade
The following example enables GbE ports 0 through 9 on an FX8-24 blade in slot 8. Ports XGE0 and
XGE1 are disabled.
switch:admin> bladecfggemode --set 1g –slot 8
You can use the
bladecfggemode --show
command to display the GbE port mode for the FX8-24
blade in slot 8, as shown in the following example.
switch:admin> bladecfggemode --show –slot 8
bladeCfgGeMode: Blade in slot 8is configured in 1GigE Mode
1GigE mode: ge0-9 ports are enabled (xge0 and xge1 are disabled)
switch:admin>