HP 3PAR StoreServ 7200 2-node HP 3PAR StoreServ 7000 Storage Service Guide (QR - Page 46

<N&gt, <MMDDhhmmYYYY&gt, Enter

Get HP 3PAR StoreServ 7200 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7200 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

7. Set up the system to wipe and rerun ootb 8. Cancel a wipe 9. Perform a deinstallation 10. Update the system for recently added hardware (admithw) 11. Check system health (checkhealth) 12. Exit > 1 WARNING! Proceeding with the system setup script causes complete and irrecoverable loss of data. Do not perform this procedure on a system that has already undergone the system setup. If you quit this setup script at any point, you must repeat the entire process If the system is ready for the system setup script, the following message appears: It appears your Cluster is in a proper manual startup state to proceed. Cluster has the following nodes: Node 0: Node 1: ... Is this correct? Enter < C > to continue or < Q > to quit ==> c 3. Verify the number of controller nodes in the system, then type c and press Enter. If the system is not ready for the system setup script, an error message appears. After following any instructions and correcting any problems return to step 2 and attempt to run the setup script again. 4. Set up the time zone for the operating site: a. Select a location from the list, type the corresponding number , and press Enter. b. Select a country, enter the corresponding number , and press ENTER. c. Select a time zone region, type the corresponding number , and press Enter d. Verify the time zone settings are correct, type 1 and press Enter. NOTE: The system automatically makes the time zone change permanent. Disregard the instructions on the screen for appending the command to make the time zone change permanent. 5. Press Enter to accept the default time and date, or type the date and time in the format , where MM, DD, hh, mm, and YYYY are the current month, day, hour, minute, and year, respectively, and then press Enter. Current date according to the system: Enter dates in MMDDhhmmYYYY format. For example, 031822572008 would be March 18, 2012 10:57 PM. Enter the correct date and time, or just press enter to accept the date shown above.=> (...) Is this the desired date? (y/n) y 6. To confirm the date setting, type y and press Enter. 7. Name the storage system using up to 31 alphanumeric characters. Type yes and press Enter to confirm the name. 46 Installing Storage Software Manually

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
7. Set up the system to wipe and rerun ootb
8. Cancel a wipe
9. Perform a deinstallation
10. Update the system for recently added hardware (admithw)
11. Check system health (checkhealth)
12. Exit
> 1
WARNING!
Proceeding with the system setup script causes complete and irrecoverable loss
of data. Do not perform this procedure on a system that has already undergone the system
setup. If you quit this setup script at any point, you must repeat the entire process
If the system is ready for the system setup script, the following message appears:
It appears your Cluster is in a proper manual startup state to proceed.
Cluster has the following nodes:
Node 0:
Node 1:
...
Is this correct?
Enter < C > to continue
or
< Q > to quit
==>
c
3.
Verify the number of controller nodes in the system, then type
c
and press
Enter
. If the system
is not ready for the system setup script, an error message appears. After following any
instructions and correcting any problems return to step 2 and attempt to run the setup script
again.
4.
Set up the time zone for the operating site:
a.
Select a location from the list, type the corresponding number
<N>
, and press
Enter
.
b.
Select a country, enter the corresponding number
<N>
, and press
ENTER.
c.
Select a time zone region, type the corresponding number
<N>
, and press
Enter
d.
Verify the time zone settings are correct, type
1
and press
Enter
.
NOTE:
The system automatically makes the time zone change permanent. Disregard
the instructions on the screen for appending the command to make the time zone change
permanent.
5.
Press
Enter
to accept the default time and date, or type the date and time in the format
<MMDDhhmmYYYY>
, where
MM
,
DD
,
hh
,
mm
, and
YYYY
are the current month, day, hour,
minute, and year, respectively, and then press
Enter
.
Current date according to the system: <date_and_time>
Enter dates in MMDDhhmmYYYY format. For example, 031822572008 would be March 18,
2012 10:57 PM.
Enter the correct date and time, or just press enter to accept the date shown
above.=> <
enter>
(...)
Is this the desired date? (y/n)
y
6.
To confirm the date setting, type
y
and press
Enter
.
7.
Name the storage system using up to 31 alphanumeric characters. Type
yes
and press
Enter
to confirm the name.
46
Installing Storage Software Manually