HP 8/20q HP StorageWorks 8/20q and SN6000 Fibre Channel Switch CIM Agent Refer - Page 17

QLGC_RemoteServiceAccessPoint : CIM_RemoteServiceAccessPoint, Principal: FC-SW2Switch_Priority=1

Page 17 highlights

The value must be within the range expressed by the FCSwitchCapabilities.MinDomainID and FCSwitchCapabilities.MaxDomainID. DomainIDLocked Property contains the configured DomainIDLocked setting. If TRUE, the switch must use the PreferredDomainID, and domainID conflicts within a fabric are resolved by segmenting the fabric. If FALSE, the switch uses the preferred domainID where possible, and fail over to an available domainID in the event of a domainID conflict. You can edit this property if the value of FCSwitchCapabilities.EditDomainIDLocked property is TRUE. PrincipalPriority Property contains an enumerated principal priority configuration for the switch. Valid values for this property are reported by the PrincipalPrioritiesSupported property of the corresponding FCSwitchCapabilities instance. Possible values are: • 2-Principal: (FC-SW2)Switch_Priority=1 • 3-Subordinate: (FC-SW2)Switch_Priority=255 • 4-Any: (FC-SW2)Switch_Priority=254 Supported WBEM operations • getClass • getInstance • enumerateInstances • enumerateInstanceNames • modifyInstance • setProperty Associations • QLGC_FCSwitchElementSettingData : CIM_ElementSettingData-1-to-1 relationship to QLGC_FCSwitch QLGC_RemoteServiceAccessPoint : CIM_RemoteServiceAccessPoint RemoteServiceAccessPoint is used by the access points sub-profile to expose connectivity information for services and interfaces on the switch. There may be as many as ten instances of RemoteServiceAccessPoint, depending on which services are enabled on the switch. Supported properties and methods CreationClassName Property contains the string QLGC_RemoteServiceAccessPoint. Name Property contains a fixed string based on the type of service. • _ServiceType Name Value_ • snmp SNMP Interface • snmp IPV6 SNMP Interface • telnet Telnet Interface • telnet IPV6 Telnet Interface • ssh SSH Interface • ssh IPV6 SSH Interface • Embedded GUI Web User Interface • Embedded GUI IPV6 Web User Interface • Ethernet Ethernet Port IP Address • Ethernet IPV6 Ethernet Port IP Address SystemCreationClassName HP StorageWorks 8/20q and SN6000 Fibre Channel Switch CIM Agent Reference Guide 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60

HP StorageWorks 8/20q and SN6000 Fibre Channel Switch CIM Agent Reference Guide
17
The value must be within the range expressed by the
FCSwitchCapabilities.MinDomainID
and
FCSwitchCapabilities.MaxDomainID
.
DomainIDLocked
Property contains the configured DomainIDLocked setting. If
TRUE
, the switch
must
use the
PreferredDomainID
, and domainID conflicts within a fabric are resolved by segmenting the
fabric. If
FALSE
, the switch uses the preferred domainID where possible, and fail over to an
available domainID in the event of a domainID conflict. You can edit this property if the value of
FCSwitchCapabilities.EditDomainIDLocked
property is
TRUE
.
PrincipalPriority
Property contains an enumerated principal priority configuration for the switch. Valid values for this
property are reported by the
PrincipalPrioritiesSupported
property of the corresponding
FCSwitchCapabilities
instance.
Possible values are:
2–Principal: (FC-SW2)Switch_Priority=1
3–Subordinate: (FC-SW2)Switch_Priority=255
4–Any: (FC-SW2)Switch_Priority=254
Supported WBEM operations
getClass
getInstance
enumerateInstances
enumerateInstanceNames
modifyInstance
setProperty
Associations
QLGC_FCSwitchElementSettingData : CIM_ElementSettingData
—1-to-1 relationship to
QLGC_FCSwitch
QLGC_RemoteServiceAccessPoint : CIM_RemoteServiceAccessPoint
RemoteServiceAccessPoint
is used by the access points sub-profile to expose connectivity
information for services and interfaces on the switch. There may be as many as ten instances of
RemoteServiceAccessPoint
, depending on which services are enabled on the switch.
Supported properties and methods
CreationClassName
Property contains the string
QLGC_RemoteServiceAccessPoint
.
Name
Property contains a fixed string based on the type of service.
_ServiceType Name Value_
snmp
SNMP Interface
snmp
IPV6 SNMP Interface
telnet T
elnet Interface
telnet
IPV6 Telnet Interface
ssh
SSH Interface
ssh
IPV6 SSH Interface
Embedded GUI
Web User Interface
Embedded GUI
IPV6 Web User Interface
Ethernet
Ethernet Port IP Address
Ethernet
IPV6 Ethernet Port IP Address
SystemCreationClassName