HP 8/20q HP StorageWorks 8/20q and SN6000 Fibre Channel Switch CIM Agent Refer - Page 27

HW_MP_ACCESS: Failed to access eeprom on MP., FW_POST_FAIL: Power On Self Test failure.

Get HP 8/20q PDF manuals and user guides View all HP 8/20q manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Name Property contains the switch WWN. ElementName Property contains the switch symbolic name. The property may be edited if FCSwitchCapabilities.ElementNameEditSupported is TRUE. NameFormat Property contains the string WWN. OtherIdentifyingInfo Property contains an array with a single string element representing the domainID of the switch. The domainID is formatted as a decimal value. OperationalStatus Property contains an array of enumerated values that represent both the configured state and the operational status of the switch. The zero position in the array contains the one of the following exclusive values: • 02-OK: All the switch ports have been enabled (ONLINE) and the switch passed boot diagnostic test. • 03-Degraded: The switch is working but a fault has been detected. • 06-Error: The switch is not working properly. • 10-Stopped: All the switch ports have been disabled (OFFLINE or DOWN). • 11-InService: All the switch ports have been placed into diagnostic mode. Property may also contain a combination of the following values: • 05-PredictiveFailure: A system failure is likely. • 32768-FW_POST_FAIL: Power On Self Test failure. • 32769-HW_MP_ACCESS: Failed to access eeprom on MP. IdentifyingDescriptions Property contains an array with a single string value of DomainID. This corresponds with the OtherIdentifyingInfo property that contains the domainID of the switch. Dedicated Property contains the enumerated value 5=Switch; identifying this instance of CIM_ComputerSystem as a switch. EnabledState Property contains the current port enabled state. This value matches the configured switch enabled state (EnabledDefault) unless the switch state has been temporarily changed. Possible values are: • 2-Enabled: Switch ports are online. • 3-Disabled: Switch ports are offline • 7-Test: Switch ports are in diagnostics mode. RequestedState Property contains the pending switch state. Switch state changes are atomic; there no pending switch state. Possible values are: • 05-NoChange, No pending state change. • 12-NA Switch may not be enabled/disabled (remote switch). EnabledDefault Property contains the configured switch state. Possible values are: • 2-Enabled: Switch ports are online. • 3-Disabled: Switch ports are offline. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch CIM Agent Reference Guide 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
HP StorageWorks 8/20q and SN6000 Fibre Channel Switch CIM Agent Reference Guide
27
Name
Property contains the switch WWN.
ElementName
Property contains the switch symbolic name. The property may be edited if
FCSwitchCapabilities.ElementNameEditSupported
is
TRUE
.
NameFormat
Property contains the string
WWN
.
OtherIdentifyingInfo
Property contains an array with a single string element representing the domainID of the switch. The
domainID is formatted as a decimal value.
OperationalStatus
Property contains an array of enumerated values that represent both the configured state and the
operational status of the switch. The zero position in the array contains the one of the following
exclusive values:
•
02
–
OK: All the switch ports have been enabled (ONLINE) and the switch
passed boot diagnostic test.
•
03
–
Degraded: The switch is working but a fault has been detected.
•
06
–
Error: The switch is not working properly.
•
10
–
Stopped: All the switch ports have been disabled (OFFLINE or
DOWN).
•
11
–
InService: All the switch ports have been placed into diagnostic
mode.
Property may also contain a combination of the following values:
•
05
–
PredictiveFailure: A system failure is likely.
•
32768
–
FW_POST_FAIL: Power On Self Test failure.
•
32769
–
HW_MP_ACCESS: Failed to access eeprom on MP.
IdentifyingDescriptions
Property contains an array with a single string value of
DomainID
. This corresponds with the
OtherIdentifyingInfo property that contains the domainID of the switch.
Dedicated
Property contains the enumerated value
5=Switch
; identifying this instance of
CIM_ComputerSystem as a switch.
EnabledState
Property contains the current port enabled state. This value matches the configured switch enabled
state (
EnabledDefault
) unless the switch state has been temporarily changed.
Possible values are:
•
2
–
Enabled: Switch ports are online.
•
3
–
Disabled: Switch ports are offline
•
7
–
Test: Switch ports are in diagnostics mode.
RequestedState
Property contains the pending switch state. Switch state changes are atomic; there no pending
switch state.
Possible values are:
•
05
–
NoChange, No pending state change.
•
12
–
NA Switch may not be enabled/disabled (remote switch).
EnabledDefault
Property contains the configured switch state. Possible values are:
•
2
–
Enabled: Switch ports are online.
•
3
–
Disabled: Switch ports are offline.