HP 8/20q HP StorageWorks Simple SAN Connection Manager User Guide (5697-0633, - Page 111

Viewing VCEM and c-Class Enclosure Properties, Supported configurations, Viewing VCEM information

Get HP 8/20q PDF manuals and user guides View all HP 8/20q manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

9 Viewing VCEM and c-Class Enclosure Properties This chapter provides procedures for viewing VCEM version 6.1 and c-Class Enclosure properties using Simple SAN Connection Manager. Supported configurations • VCEM 6.1 and Virtual Connect Manager configured to the recommended HP guidelines (all servers and SAN fabrics configured correctly and the VCM managed by VCEM) NOTE: HP recommends that VCEM 6.1 is installed on a different server from the SSCM management station. • For SAN fabrics, SSCM supports both factory default and VC WWN addresses. With VC defined WWN addresses, additional host to blade/bay associations are available. Viewing VCEM information Simple SAN Connection Manager provides easy access to information about VCEM within your SAN. Use the VCEM Configuration dialog box to establish associations between each blade and their respective HP BladeSystem c-Class Enclosure. To log in and view VCEM configuration: 1. Start the Simple SAN Connection Manager. See "Starting Simple SAN Connection Manager" on page 30. 2. Open the VCEM Configuration dialog box (Figure 85). 3. Check in the Enable VCEM Discovery check box. 4. Enter the username and password, and then enter the IP address of the VCEM host server. 5. Click OK. Figure 85 SSCM VCEM Configuration HP StorageWorks Simple SAN Connection Manager User Guide 111

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
HP StorageWorks Simple SAN Connection Manager User Guide
111
9
Viewing VCEM and c-Class Enclosure Properties
This chapter provides procedures for viewing VCEM version 6.1 and c-Class Enclosure properties using
Simple SAN Connection Manager.
Supported configurations
•
VCEM 6.1 and Virtual Connect Manager configured to the recommended HP guidelines (all servers
and SAN fabrics configured correctly and the VCM managed by VCEM)
NOTE:
HP recommends that VCEM 6.1 is installed on a different server from the SSCM
management station.
•
For SAN fabrics, SSCM supports both
factory default
and
VC
WWN addresses. With VC defined
WWN addresses, additional host to blade/bay associations are available.
Viewing VCEM information
Simple SAN Connection Manager provides easy access to information about VCEM within your SAN. Use
the VCEM Configuration dialog box to establish associations between each blade and their respective HP
BladeSystem c-Class Enclosure.
To log in and view VCEM configuration:
1.
Start the Simple SAN Connection Manager. See
“Starting Simple SAN Connection Manager”
on
page 30.
2.
Open the VCEM Configuration dialog box (
Figure 85
).
3.
Check in the
Enable VCEM Discovery
check box.
4.
Enter the username and password, and then enter the IP address of the VCEM host server.
5.
Click
OK
.
Figure 85
SSCM VCEM Configuration